Specification Sheet
The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. Revised 7/29/16 S/C Printed in U.S.A.
The manufacturer reserves the right to, and does from time to time, make changes and improvements in designs and dimensions. © 2015 by Bobrick Washroom Equipment, Inc.
Technical Data
L
2''
50mm
2-1/4''
55mm
3-1/8''
80mm
5/16''
8mm
Snap Flange Cover
3-1/4''
85mm
Dia.
1-1/2''
38mm
Mounting Flange
3-1/8''
80mm
Model No. Bar Length L
B-530 x 18 18'' (455mm)
B-530 x 24 24'' (610mm)
1. Mounting Kits — Bobrick has a selection of mounting screws and fasteners available for different types of installations; one Bobrick
mounting kit is required for each flange.
SPECIFICATION:
Towel bar shall be type-304 stainless steel with satin finish. Towel bar shall have 18-gauge (1.2mm) wall thickness and 1" (25mm) outside diameter.
Clearance between the towel bar and wall shall be 1-1/2" (38mm). Concealed mounting flanges shall be 11-gauge (3.2mm) thick stainless steel plate,
2'' x 3-1/8'' (50 x 80mm), and equipped with at least two screw holes for attachment to wall. Flange covers shall be 22-gauge (0.8mm) stainless steel,
3-1/4'' (85mm) diameter, and shall snap over mounting flanges to conceal mounting screws. Ends of towel bar shall pass through flanges and be
welded to form one structural unit.
Towel Bar shall be Model ____________ (insert model number) of Bobrick Washroom Equipment, Inc., Clifton Park, New York;
Jackson, Tennessee; Los Angeles, California; Bobrick Washroom Equipment Company, Scarborough, Ontario; Bobrick Washroom
Equipment Pty. Ltd., Australia; and Bobrick Washroom Equipment Limited, United Kingdom.
2. Grab Bar Fastener — Bobrick has a grab bar fastening system that secures all Bobrick grab bar series; one Bobrick fastener is
required for each flange.
MATERIALS:
Towel Bar — 18-8, type-304, 18-gauge (1.2mm) stainless steel tubing with satin finish. 1" (25mm) outside diameter. Ends are welded to flanges.
Clearance between the towel bar and wall is 1-1/2" (38mm).
Concealed Mounting Flanges — 18-8, type-304, 11-gauge (3.2mm) thick, stainless steel plate. 2'' x 3-1/8'' (50 x 80mm) with holes for attachment
to wall.
Snap Flange Covers — 18-8, type-304, 22-gauge (0.8mm) drawn stainless steel with bright polish finish. 3-1/4'' (85mm) diameter x
5/8'' (16mm) deep. Each cover snaps over mounting flange to conceal mounting screws.
STRENGTH:
Towel bar will support loads in excess of 900 pounds (408-kg) if properly installed.
Caution: Towel bars are no stronger than the anchors or walls to which they are attached and, therefore, must be firmly secured in order to support
the loads for which they are intended.
INSTALLATION:
Provide concealed anchor device or backing as specified or required in accordance with local building codes before wall is finished. Fasten
concealed mounting flanges to anchor device or backing. Snap flange covers over each mounting flange to conceal mounting screws. Concealed
anchor devices and mounting screws are not included with this towel bar and must be specified as an accessory.
Important Notes:
EXTRA-HEAVY-DUTY
TOWEL BARS WITH
CONCEALED MOUNTING
AND SNAP FLANGE
B-530
Mounting Kit No. Description
252-30 Consists of (3) #14'' x 2½'' (M6.3 x 64mm) type-304 stainless steel, Phillips round-head, sheet-metal screws.
2583 Consists of (3) 1/4''–20'' x 3/4'' (M6.3–1 x 89mm) type-304 stainless steel, Phillips round-head, machine screws
with plated-steel toggle nuts.
2586 Consists of (2) 1/4''–20'' x 1/2'' (M6.3–1 x 51mm) type-304 stainless steel, Phillips round-head, machine screws with
metal expansion shields.
WingIt™ Fastener No.. Description
251-4 Consists of (3) 10''–32'' x 5/16'' round-head, Phillips 18/8 stainless steel screws. (1) WingIt grab bar fastener.