Installation Sheet

ManualsBrandsBobrick ManualsAccessoriesBobrick Left Hand Folding Shower Seat with Padded Cushion

ulysses

INSTALLATION INSTRUCTIONS

BOBRICK SHOWER SEAT MODELS B-517 AND 518

Figure 1 Figure 2

Installation to Wall. Secure unit to wall at points indicated by an S, with the two Mounting Flanges located at top and the Baseplate

and Guide Bracket below. The bottom of the Support Tube must be positioned within the Baseplate and Guide Bracket before they are

secured to wall.

* Mounting height of shower seat must comply with local building codes.

1. Install Mounting Flanges to Wall.

A. Locate seat horizontally on wall to comply with local building codes.

B. Use Mounting Flanges as templates to mark holes.

1) Check to make sure seat surface is horizontal and Mounting Flanges are ﬂat against wall.

2) Make sure holes marked for Mounting Flanges align with wall backing.

C. Drill holes for Mounting Flange fasteners and secure Mounting Flanges to wall with appropriate fasteners.

D. Check to see if seat moves freely from horizontal to vertical position.

IMPORTANT NOTES

1) For stud wall construction, install backing (not furnished by Bobrick) (see Figure 2). Backing must be provided before

the ﬁnished shower wall is applied. Secure with #14 x 2-1/2" (6.3 x 65mm) stainless steel mounting screws furnished by

manufacturer.

2) For prefabricated shower stalls, adequate backing must be provided by the shower stall manufacturer (see Figure 2).

Secure with #14 x 2-1/2" (6.3 x 65mm) stainless steel mounting screws furnished by manufacturer. Bobrick offers a mounting

kit for installing shower seats. For additional mounting kits please order 252-30. One mounting kit is required for each ﬂange.

3) For concrete walls, provide ﬁber plugs or expansion shields for use with furnished screws, or provide 1/4" (6mm) toggle

bolts or expansion bolts. Wall anchors not furnished by Bobrick.

2. Install Baseplate with Spring and Guide Bracket to Wall.

A. Support seat in level horizontal position.

B. Locate Guide Bracket on wall with bottom center of Support Tube resting on bottom of Guide Bracket (see Figure 2).

C. Mark holes on wall using Guide Bracket as a template.

D. Drill holes in wall for appropriate fasteners (see Figure 3). Install fasteners.

E. Place Baseplate on wall with curled spring at top aligning holes in Baseplate with fasteners.

F. Place Guide Bracket over Support Tube and fasten to wall.

continued . . .

Left-Hand Seat Shown

Universal/Accessible Design

Recommended

Mounting Height

*17'' to 19''

430 to 485mm

Base Plate

with Spring at Top

Support Bracket

Guide Bracket

Finish Face of Floor

9-3/8''

240mm

22-1/4''

565mm

6-1/16''

155mm

7-1/4''

185mm

1-7/16''

35mm

5-1/2''

140mm

Finish Face of Wall

22-11/16''

575mm

Mounting

Flange (2)

Concealed wall backing

to comply with

local building codes,

not furnished

by Bobrick.

*Consult local building codes

16-3/16''

410mm

6-11/16''

170mm

21-1/4''

540mm

13-1/4''

340mm

16-7/16''

420mm

19-1/2''

495mm

32-7/8''

835mm

14-3/4''

375mm

2-1/4''

55mm

Dia.

Bolt Circle

1-1/8''

30mm

2-1/4''

55mm

Summary of content (2 pages)

PAGE 1
INSTALLATION INSTRUCTIONS BOBRICK shower seat MODELs B-517 and 518 Figure 1 Figure 2 32-7/8'' 835mm 6-11/16'' 19-1/2'' 170mm 495mm 22-11/16'' 575mm 16-7/16'' 420mm Finish Face of Wall 13-1/4'' 5-1/2'' 340mm 140mm 1-7/16'' 35mm 16-3/16'' 21-1/4'' 410mm 540mm 14-3/4'' Mounting Flange (2) 375mm 22-1/4'' 565mm 6-1/16'' Support Bracket 55mm Dia.
PAGE 2
3. Install Safety Plate to Wall Safety Plate is to be mounted on wall near Shower Seat in order to properly advise users of the Seat's weight restrictions. Correct installation of the Safety Plate will ensure that the Shower Seat meets A.N.S.I. Standards. Permanently affix Safety Plate to wall on either side of the Shower Seat at a minimum height of 30" (760mm). If mounted above Seat, the Plate must be high enough so that it is not covered when Seat is on the up position.