OWNER’S MANUAL ProSmart TEAMBMPRO.
POWERING YOUR ADVENTURES With over 50 years’ experience in power solutions combined with manufacturing and design facilities in Melbourne, Australia, BMPRO are the leading experts in RV power and control management. Inspired by the great outdoors, we have created a range of rugged, smart and reliable products to power your adventures.
SAFETY PRECAUTIONS Please read the Safety Precautions before installing or using ProSmart. Be sure to observe all precautions without fail. Failure to observe these instructions properly may result in personal damage, or personal injury which depending on the circumstances may be serious and cause loss of life. Only install the SmartSense gas cylinder/propane gas sensor as described in this manual. No field assembly is required.
CONTENTS SAFETY PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . 4 ABOUT PROSMART . . . . . . . . . . . . . . . . . . . . . . . 8 PROSMART SYSTEM DIAGRAM . . . . . . . . . . . . . . . . . .9 DESCRIPTION OF PARTS. . . . . . . . . . . . . . . . . . . . . 10 SMARTLINK . . . . . . . . . . . . . . . . . . . . . . . . . 10 MOUNTING THE SMARTLINK . . . . . . . . . . . . . . . . . . . 12 THE PROSMART APP . . . . . . . . . . . . . . . . . . . . . . 13 COMPATIBLE DEVICES . . . . . . . . . . . . . . . . . . .
SMARTTEMP . . . . . . . . . . . . . . . . . . . . . . . . . 27 PAIRING SMARTTEMP SENSORS . . . . . . . . . . . . . . . . . 27 SMARTTEMP PAIRING UNSUCCESSFUL . . . . . . . . . . . . . . 29 UNPAIRING SMARTTEMP SENSORS . . . . . . . . . . . . . . . 29 BATTERY REPLACEMENT . . . . . . . . . . . . . . . . . . . . 30 REPLACING SMARTPRESSURE SENSOR BATTERIES . . . . . . . . . 30 REPLACING SMARTSENSE SENSOR BATTERIES . . . . . . . . . . 31 REPLACING SMARTTEMP SENSOR BATTERIES . . . . . . . . . . . 31 SERVICING .
ABOUT PROSMART ProSmart is a system that allows you to easily monitor water levels, gas levels, tyre pressure, temperatures and battery charge while on your adventures, all from an easy-to-use app on your smartphone. Included in your ProSmart package is SmartLink, a powered node that you can easily install and pair to your phone, which allows you to view both your wired and wireless sensors through a Bluetooth connection.
PROSMART SYSTEM DIAGRAM 9
DESCRIPTION OF PARTS SMARTLINK 1 2 4 3 11 5 10 9 8 7 6 1. DIP SWITCH Used to configure the ports on the SmartLink. Leave in the “ON” position. 2. DISPLAY PORT (UNUSED) 3. CAN BUS PORT (UNUSED) 4. WATER TANK SENSOR CONNECTIONS Used to connect BMPRO water sensors. 5. HELP VIDEO QR CODE Scan the QR code to view information about ProSmart, including FAQs and the manual at teambmpro.com 6. SERIAL NUMBER Contains the passkey pin required when pairing the SmartLink to the ProSmart App. 7.
8. PAIRING LED LED indicator which shows status when pairing or unpairing. STATE LED STATUS Initialisation Flashing white and yellow Pairing Flashing blue The maximum of four devices has been reached Flashing amber-green All devices have been forgotten Flashes red once 9. PAIRING BUTTON Used to pair and unpair devices from SmartLink. If the button is held for 10 seconds, all paired devices will be forgotten by the SmartLink.
MOUNTING THE SMARTLINK The SmartLink is designed to be mounted to the wall directly with screws. A hole for the connectors must be drilled before mounting. To maximise antenna performance and to avoid signal degradation, care should be taken to not place the SmartLink near conductive or metal objects. Once the SmartLink has been mounted to the wall, connect all the connections.
THE PROSMART APP Download the ProSmart App and enjoy the freedom to monitor your sensors around your RV remotely. COMPATIBLE DEVICES The ProSmart App is compatable with iOS 13 or later and Android 8 or later. Search for ProSmart in the Apple App Store or Google Play. Apple App Store QR Code Google Play QR Code USING THE PROSMART APP FOR THE FIRST TIME When opening the ProSmart App for the first time, you will be greeted with the Welcome screen. Press Start to begin using the app.
Your SmartLink will need to be configured to work with the ProSmart App. In the Prepare your SmartLink screen, press Continue. If you are using an Android phone, the ProSmart App requires access to your smartphone’s location services in order to work with your SmartConnect sensors.
The ProSmart App is now ready to pair with SmartLink. Once the Pair your SmartLink screen displays, press the pairing button on the SmartLink. The LED on the SmartLink will begin flashing blue. The SmartLink will now be available for pairing for 60 seconds. If a notification appears requesting pairing, press Pair & Connect. In the pop-up that appears, type your 6-digit passkey pin. This is located on the SmartLink itself. The ProSmart App will now be connected to the SmartLink.
HOME SCREEN Once connected to the SmartLink, the ProSmart App will display the Home screen. The Home screen will display all sensors connected to your SmartLink. Wired sensors connected to the SmartLink will appear with a wired icon. Connected batteries will display the battery voltage and its current state of charge.
Filtering Sensors You can filter the displayed sensors by pressing All Sensors. Here you can choose to display a single type of sensor on the Home screen. SETTINGS Press the Settings button from the Home screen to access the app settings.
Wired Sensors Up to 4 connected water tanks, 1 wired temperature sensor and a battery can be configured in the Wired Sensors screen. Water tanks can be set as Clean or Dirty. Battery chemistry can be set as Lead Acid or LiFePo4 (Lithium). All wired sensors can be toggled to display on the Home screen by ticking or unticking the Show on home screen checkbox. Each sensor can be renamed by pressing the edit icon.
SMARTPRESSURE The SmartPressure Tyre Pressure Monitoring System (TPMS) allows the monitoring of your tyre pressure through ProSmart. The SmartPressure sensor will transmit every 10 minutes when your RV is stationary and every minute when in motion. The SmartPressure sensor will transmit at a faster rate if a leak in the tyre is detected. In this situation: 9 Wait for the sensor to send the information 9 Check if the sensor is installed correctly SmartPressure Sensor 9 Check the sensor’s battery level.
PAIRING SMARTPRESSURE SENSORS To pair SmartPressure sensors: 1. Press the Settings button. 2. In the Settings screen, press SmartConnect sensors. 3. Underneath SmartPressure, from the drop-down, choose the location of the SmartPressure sensor you want to pair. 4. Press Add Sensor.
5. A pop-up will appear with pairing instructions. 6. Press OK. 7. Install the pressure sensor on the same selected tyre. Refer to the section Installing SmartPressure Sensors. 8. Once pairing is successful, the sensor, tyre pressure and tyre temperature will appear on the Home screen. SMARTPRESSURE PAIRING UNSUCCESSFUL If pairing was unsuccessful, a message will appear stating “Sensor Not Paired”. Press OK to attempt pairing again.
PRESSURE SIGNAL NOT DETECTED If a valid pressure signal is not detected, the pressure will show as 0. In this situation: 9 Wait for the sensor to send the information 9 Check if the sensor is installed on the tyre 9 Check the sensor battery level UNPAIRING SMARTPRESSURE SENSORS To unpair SmartPressure sensors: 1. Go to the Your Sensors page. 2. On the SmartPressure sensor you want to unpair, press the bin icon.
SMARTSENSE The SmartSense propane gas sensor allows you to directly monitor the levels of gas in a gas cylinder with ProSmart. INSTALLING SMARTSENSE SENSORS SmartSense sensors can be installed by following the below instructions: 1. On the propane gas tank, ensure the base is clean. Remove any debris, excess paint or rust. 2. The sensor mounts to the base of the tank using SmartSense Propane Gas Sensor magnets.
PAIRING SMARTSENSE SENSORS To pair SmartSense sensors: 1. Press the Settings button. 2. In the Settings screen, press SmartConnect sensors. 3. Underneath SmartSense, from the drop-down, choose the location of the SmartSense sensor you want to pair. 4. Select the bottle size of the gas tank.
5. Press Add Sensor. 6. A pop-up will appear with pairing instructions. 7. Press OK. 8. If this is the firs time this sensor has been synced, press the orange sync button on the SmartSense sensor 6 times. This permanently disables Sleep Mode, which is the factory setting. After the first use, only a single press is required to sync the device. 9. Once pairing is successful, the sensor, level of gas and battery level of the sensor will appear on the Home screen.
SMARTSENSE PAIRING UNSUCCESSFUL If pairing is unsuccessful, a message will appear stating “Sensor Not Paired”. Press OK to attempt pairing again. If the SmartSense sensor continues to fail to pair: 9 Move the propane tank and sensor closer to the SmartLink. 9 Check the sensor battery level. Refer to the BATTERY REPLACEMENT section to check the battery level of the sensor and for instructions on battery replacement.
SMARTTEMP The SmartTemp Bluetooth temperature sensors allow you to monitor temperatures throughout your RV using ProSmart. PAIRING SMARTTEMP SENSORS To pair SmartTemp sensors: 1. Press the Settings button. 2. In the Settings screen, press SmartConnect sensors. SmartTemp Sensor 3. Underneath SmartTemp, from the drop-down, choose the location of the SmartTemp sensor you want to pair.
4. Press Add Sensor. 5. A pop-up will appear with pairing instructions. 6. Press OK. 7. Turn on the SmartTemp sensor by pressing and hold the sensor power button until the light turns green. 8. Once pairing is successful, the sensor, temperature and humidity level will appear on the Home screen.
SMARTTEMP PAIRING UNSUCCESSFUL If pairing is unsuccessful, a message will appear stating “Sensor Not Paired”. Press OK to attempt paring again. Refer to the BATTERY REPLACEMENT section to check the battery level of the sensor and for instructions on battery replacement. UNPAIRING SMARTTEMP SENSORS To unpair SmartTemp sensors: 1. Go to the Your Sensors page. 2. On the SmartTemp sensor you want to unpair, press the bin icon.
BATTERY REPLACEMENT The monitoring system displays battery level information to help you know when you need to change the batteries of your SmartConnect devices. To check if any SmartConnect sensor batteries need to be changed, check the battery icon on the sensor in the home screen. The icon will indicate if the battery is low or not. If the battery is low, it will need to be replaced.
REPLACING SMARTSENSE SENSOR BATTERIES SmartSense sensor batteries can be replaced by following the below instructions: Using a small screwdriver, lift the lid which is held by the snap fit. Carefully lift the board with the electronics. Replace the CR2032 battery. Place the lid back into base and press down fully to reengage all 4 snap fits.
SERVICING Do not attempt to service the SmartLink yourself, OR dismantle, modify or repair the SmartLink yourself; this will void your warranty. If your SmartLink requires servicing, please consult your BMPRO dealer or visit teambmpro.com for assistance. FAQS AND TROUBLESHOOTING Need more help troubleshooting your ProSmart? Refer to our website for more information at teambmpro.com/technical-support How many devices can I pair to the SmartLink? Up to four devices can be paired to the SmartLink at once.
SPECIFICATIONS SmartLink Input Voltage Range 8V to 16V Battery Drain < 20mA Ambient Temperature -20°C to 60°C (-4°F to 140°F) Dimensions (mm) 156 x 76 x 23 Wired temperature Sensor Temperature Measurement Range -20°C to 60°C (-4°F to 140°F) SmartPressure Sensor Pressure Measurement Range 0 PSI to 99 PSI (0 kPa to 680 kPA) SmartTemp Sensor Temperature Measurement Range -20°C to 60°C (-4°F to 140°F) 33
COMPLIANCE This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
WARRANTY TERMS AND CONDITIONS (AUSTRALIA) Registering your BMPRO product is an important step to ensure that you receive all the benefits you are entitled to. Please visit teambmpro.com to complete the online registration form for your new product today. 1. BMPRO goods come with guarantees that cannot be excluded under Australian Consumer Law. You are entitled to a replacement or refund for major failure.
LIMITED WARRANTY TERMS AND CONDITIONS (USA) Registering your BMPRO product is an important step to ensure that you receive all the benefits you are entitled to. Please visit teambmpro.com to complete the online registration form for your new product today. What this Limited Warranty Covers This warranty covers any defect or malfunction in your BMPRO product. Under this warranty you are entitled to have such goods replaced, repaired or refunded.
POWERING YOUR ADVENTURES. TEAM BMPRO .COM BMPRO customerservice@teambmpro.com )FOEFSTPO 3E ,OPYåFME 7*$ "VTUSBMJB | 6OJU & 8JOETPS "WF &MLIBSU */ 64" teambmpro.