HEX31WP-TX User Manual RevA0 HEX31WP-TX User Manual
HEX31WP-TX USER MANUAL Contents Thank you for purchasing this product. Introduction 03 For optimum performance and safety, please read these instructions carefully before connecting, operating or adjusting this product. Please keep this manual for future reference.
HEX31WP-TX USER MANUAL Introduction Our HEX31WP HDMI / USB-C wall plate HDBaseT™ Transmitter is a multi-format 4K input switcher solution delivering HDMI and USB-C inputs up to 70m at 1080p (40m at 4K 60Hz 4:2:0). The HEX31WP-TX features both manual or automated source selection and includes display on / off control via CEC, RS-232 and IR (via compatible HDBaseT™ Receiver / Matrix).
HEX31WP-TX USER MANUAL Front Panel Description 1 2 3 9 10 4 5 6 7 8 1 USB-C Input - Type C USB port to connect to USB-C source device 2 Output ON / OFF Button - Triggers the output on / off sequence (see Output On / Off section on next page) 3 HDBaseT™ link status indicator - Illuminates when the Transmitter is connected to the Receiver / Matrix successfully 4 IR Receiver - Built in IR sensor for IR pass through 5 HDMI Input 1 - Type A HDMI port to connect HDMI source device 6 HDMI Input 2 - Type
HEX31WP-TX USER MANUAL Output On/Off Function The HEX31WP-TX features a variety of ways that the unit can be automated to, or allow for, the powering of the display connected to the HDBaseT™ receiver. Output On/Off Button The Output On/Off button can be programmed to power on, or off, the display connected to the HDBaseT™ Receiver via CEC, IR or RS-232 as required by the user. The default setting on the unit is enabled for CEC (Consumer Electronic Control), but disabled for IR and RS-232.
HEX31WP-TX USER MANUAL Auto Switching The HEX31WP-TX can automatically switch sources based on when an input signal is detected or lost. This feature will automatically switch to any new source that is connected to the HEX31WP-TX, and subsequently will switch back to the previous source when a signal is lost. To enable or disable this feature, press and hold the the Auto Switching button for 3 seconds. The Auto Switching button LED will blink to confirm this command has been received.
HEX31WP-TX USER MANUAL EDID Control EDID (Extended Display Identification Data) is a data structure that is used between a display and a source. This data is used by the source to find out what audio and video resolutions are supported by the display. By pre-determining the video resolution and audio format of the source and display device you can reduce the time needed for EDID hand shaking thus making switching quicker and more reliable.
HEX31WP-TX USER MANUAL RS-232 Configuration The RS-232 port is used for configuration / control of the product, including pass through of RS-232 commands to a compatible Blustream HDBaseT™ Receiver / Matrix device. The default RS-232 communication settings are: Baud rate: 57600 Data bit: 8 Stop bit: 1 Parity bit: none Common Mistakes • Carriage return – Some programs do not require the carriage return where as other will not work unless sent directly after the string.
HEX31WP-TX USER MANUAL RS-232 Commands Continued... EDID xx DF zz EDID xx CP yy EDIDSAVE zz CECAUTO ON/OFF OUT xx CEC INPUT yy OUT xx CEC VOLUP OUT xx CEC VOLDOWN OUT xx CEC MUTE OUT xx CEC PON OUT xx CEC POFF OUT xx CEC yy:yy:yy RS232BAUD z RS232ON y:z:a RS232OFF y:z:a RS232ON DISABLE RS232OFF DISABLE EDID xx DF zz Set Input xx EDID To Default EDID zz xx=[00]: All Input Port, [01...03]: Input Port zz=00: HDMI 1080p@60Hz, Audio 2ch PCM zz=01: HDMI 1080p@60Hz, Audio 5.
DC Power USB-C Cat 6 Infrared HDMI RS-232 Example Schematic HEX31WP-TX HDMI & USB-C SOURCE Display HDBaseT™ RX Compatible Blustream HDBaseT™ Matrix or Receiver product. * Technical performance is subject to the features supported on the connected HDBaseT™ device. Optional PSU when not powered via HDBaseT™ Control Processor HEX31WP-TX USER MANUAL www.blustream.com.au | www.blustream.co.
HEX31WP-TX USER MANUAL Specifications HEX31WP-TX • Video Input Connectors: 2 x HDMI Type A, 19-pin, female; 1 x USB-C Type C, 24-pin, female • Video Output Connectors: 1 x HDBaseT™ RJ45 connector • RS-232 serial port: 1 x 3-Pin Phoenix connector • IR Input port: 1 x 3-Pin Phoenix connector • Product upgrade: 1 x Micro USB, female • Local power input: 1 x 2-Pin Phoenix connector • Casing Dimensions (W x H x D): 136mm x 76mm x 44mm (without faceplate) • Faceplate Dimensions (W x H x D): 146mm x 86mm x 6mm •
HEX31WP-TX USER MANUAL Installer Notes: 12 www.blustream.com.au | www.blustream.co.
HEX31WP-TX USER MANUAL contact support@blustream.co.uk | support@blustream.com.
www.blustream.co.uk www.blustream.com.