En De BLUETOOTH HEADSET User Manual V2.0 + EDR Version Model NO.
-2-
En Contents 1. Introduction...................................................................................................5 Bluetooth headset technology .............................................................................................5 2. Charging and Basic Operation ..............................................................6 Headset BT-ET07 Structure Sketch ...............................................................................6 Chargers and Batteries...........................
-4-
1. Introduction Bluetooth Headset BT-ET07 can be used with any phones that support Bluetooth wireless technology. This allows you the freedom to make and receive calls while on any time and any where. Read this user manual carefully before using the headset. Read also the user manual for your phone, which provides important safety and maintenance information. Keep the headset away from children. For the user manual, all rights reserved to manufacturer.
2.
Before you can start to use the headset, you must charge the battery, and pair the headset with a compatible phone. Note: Parts of the headset are magnetic. Metallic materials may be attracted to the headset. Do not place credit cards or other magnetic storage media near the headset, because information stored on them may be erased. Chargers and Batteries Check the model number of any charger before using it with this device.
Connect the charger to a wall outlet or the car charger (options) to the accessory power outlet of your car. The red indicator light turns on during charging.(If you do not use the headset for long periods, causing the battery out of power completely,the red LED will not light, it’s normal).The red LED will turn off automatically or appear to flash after being fully charged. The charging time is for about 2-3 hours based on different models.
However, the talking and standbz times maz varz when used with different mobile phones, products that use a Bluetooth connection, usage settings, usage styles, and environments. When the battery is running out of power, the headset beeps, and the red indicator light flashes every 2 seconds .Then please charge the battery asap. Note: If charging the headset when it is on, the headset will automatically turn off when start charging. The headset can be turned on for using while in charging status.
Pairing the Headset with a Compatible Device 1. Turning on your phone and the headset. 2. Activate the Bluetooth function on the phone. (See the user guide of your phone for instructions). 3. Press and hold the Multifunktion key for 2 sec. until the blue and red indicator lights flashes in turn. When you release the key, the headset is ready to be paired. Note: If the headset paired already, you should cut the current connection, then it can pair again. 4. Set the phone to search for Bluetooth devices.
Disconnecting the Headset To disconnect the paired headset from your phone (for example, to connect the phone or headset to another Bluetooth device), turn off the headset, or disconnect the headset from the Bluetooth menu of your phone. You do not need to delete the paired headset from the phone in order to disconnect it.
3. Basic Use Wearing the Headset The headset is ready to wear on the right ear ( Pic. 1). If you want to use it on the left ear, please softly lift up the earhook ( Pic 2 ) and rotate it ( Pic. 3), and push it back to the suitable place , then wear to your ear( Pic. 4). Adjusting the Headset Ear hook The ear hook can be adjusted to suit the different ear size and make you feel comfortable.
Adjusting the Headset Volume Press the VL+key to increase or the VL-key to decrease the volume. Note: There are 15 volume levels available for adjusting to high or low, moreover high volume and low volume can be identified by different tone. Whenever it reaches the maxi / mini volume, you will hear two beeps. Call Handling To Make a Call To make a call, dial the number with your phone, and press the answer key on your phone.
To Mute or Cancel Mute of Microphone To mute the microphone during a call, press the headset MFB and VL+key simultaneously until it beeps. Repeating this operation can cancel the mute function. Transferring a Call To transfer the call from the headset to a compatible phone, press the headset MFB and VL- key for 3 seconds simultaneously until it beeps. Or use the related function in your phone.
Troubleshooting If you can’t connect the headset to your phone, do as following: • Ensure the headset is charged, turned on and paired and connect to your phone. • Ensure the Bluetooth function is active on your phone. Check the headset iswithin 10 meters (30 feet) from your phone and there are no obstructions between the headset and the phone, such as walls or other electronic devices. If you don’t use headset for long time, or maintain the battery well, thus will make the battery invalid.
4. Battery Information This headset is powered by rechargeable battery. The new battery can achieve the best function only after two or three times fully charged and discharged cycles. But it eventually will be invalid after being charged and discharged for hundreds of times.You only can charge the battery with our designated headset charger. Unplug the charger from the electrical plug and the device when you don’t use it.
5. Terms Interpretation Pairing: Verify between the two devices (Bluetooth headset and mobile phone) Connect: The two devices build up connection for communication after been approved by each other.
6. Appendix Appendix 1: Headset Standard Accessories Model No.
Appendix 2: Specification Model No. Solution Main Chip Bluetooth Version Frequency Input Power RF Output Power Data Transfer Rate Headset Passkey Operation Range Supply Current Battery Voltage Operating Temperature Dimension Weight Charging Time Talking Time Standby Time BT-ET07 CSR BlueCore4-Audio ROM V2.0 + EDR 2.4GHz~2.4835GHz ISM Band 45mW 0dBm 2Mbps ~ 3Mbps 0000 Up to 10 Meters(30 feet) 5mA~20mA 3.6V rechargeable Li-polymer battery DC 5.0V~6.
Appendix 3: Indicator LED status LED Blue Red Status Flashing continued 4 times and red LED flashing 2 times (The red LED is not flashing for some headsets, it’s normal) Flashing 1 time for every 2 seconds (or for every 5 seconds for some headsets) Flashing 1 time for every 10 seconds (or for every 5 seconds for some headsets) Flashing continued 2 times for every 8 seconds Flashing continued 4 times rapidly Keeping on Lighting Flashing (not in charging status) Flashing in turn rapidly Red & Blue All in
Appendix 4: Operation Statement. Part 1 Operation Methods Status Turning on Long press the MFB key for 2 seconds The blue LED flashes 4 times and red LED flashes 2 times.
Appendix 4: Operation Statement.
- 23 -
De BLUETOOTH HEADSET Anleitung V2.0 + EDR Version Model NO.
De Inhaltsverzeichnis 1. Einführung .................................................................................................. 27 Bluetooth Headset Technik ..................................................................................................27 2. Laden und Grundfunktionen ................................................................ 28 Headset BT-ET07 - Teileskizze ......................................................................................28 Ladegeräte und Akkus ........
- 26 -
1. Einführung Das Bluetooth Headset BT-ET07 kann mit jedem Handy verwendet werden, das über eine Bluetooth-Funktion verfügt. Damit sind Sie in der Lage, jederzeit und überall Telefonate zu führen und entgegenzunehmen. Lesen Sie diese Anleitung gründlich durch, bevor Sie das Headset benutzen. Lesen Sie auch die Anleitung Ihres Handys, in der Sie wichtige Sicherheitshinweise und Anleitungen finden. Das Headset gehört nicht in Kinderhände! Alle Rechte dieser Bedienungsanleitung liegen beim Hersteller.
2. Laden und Grundfunktionen Headset BT-ET07 - Teileskizze Das Headset besteht aus folgenden Teilen: 1. 2. 3. 4. 5. Multifunktionsknopf LED-Anzeige Mikrofon Lautstärke-leiser-Knopf (VL-) Lautstärke-lauter-Knopf (VL+) - 28 - 6. 7. 8. 9. 10.
Bevor Sie Ihr Headset verwenden können, müssen Sie den Akku laden und das Headset mit einem kompatiblen Handy verbinden. Achtung: Teile des Headsets sind magnetisch. Metallische Gegenstände könnten angezogen werden.
Laden des Headsets Das Headset hat einen eingebauten, nicht zu entfernenden, Akku. Versuchen Sie auf keinen Fall, den Akku gewaltsam zu entfernen – dabei könnten Sie das Headset beschädigen! Verbinden Sie das Ladegerät mit dem Headset, wie auf der Abbildung zu sehen. Verbinden des Headsets mit einem kompatiblen Gerät 1. Schalten Sie Ihr Handy und das Headset ein. 2. Aktivieren Sie die Bluetooth-Funktion in Ihrem Handy. (Die Anleitung dazu finden Sie im Handbuch Ihres Handys.) 3.
4. Lassen Sie Ihr Handy nach Bluetooth-Geräten suchen. (Die Anleitung dazu finden Sie im Handbuch Ihres Handys.) 5. Wählen Sie aus der Liste der gefundenen Geräte das BT-ET07 aus. 6. Geben Sie den Schlüssel 0000 ein, um das Headset mit Ihrem Handy zu verbinden. Bei einigen Geräten müssen Sie die Verbindung manuell herstellen. Schauen Sie in das Handbuch Ihres Handys, um Details darüber zu erfahren. Die Grundverbindung zwischen Headset und Handy müssen Sie nur einmal herstellen.
www.blu-max.