Radio receiver Radio Transmission For Touch Probes For Tool Setting Probes For Bore Gauges For Special Measuring Systems Installation instructions Type RC66 1
Copyright © 2021 – All contents, especially texts, photographs and graphic representations are protected by copyright. All rights reserved by Blum-Novotest GmbH, including reproduction, copying, publication and translation. Translation of the original German document. The language version of the manufacturer (DE) is relevant for the technical content. Subject to technical change without notice. All brands stated in this document are the property of the respective brand owner.
Table of Contents Table of Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 1.1 1.2 Legend – Warnings, marks, symbols. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Abbreviations and technical terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 2.
Introduction 1. Introduction Please read and observe these instructions and the other applicable documents! 1.1 Legend – Warnings, marks, symbols WARNING! This information indicates a dangerous situation that, if not avoided, may result in death or serious injury. ... and shows you how you can avoid it. CAUTION! This information indicates a dangerous situation that, if not avoided, may result in mild to medium injury. ... and shows you how you can avoid it.
Safety 2. Safety 2.1 Intended use The BLUM measuring component RC66 is exclusively developed and intended: • For use within the machine room of a processing centre. • For use within the machine room of a milling machine. • for communication between the wireless measuring device and the interface. • for use with one or more wireless BLUM measuring devices. • for use with a BLUM Interface IF20. • for use with a BLUM Interface IF59. • for use with the BLUM software GeKo Programmiertool.
Safety 2.3 General safety instructions WARNING! Risk of electric shock due to improper work on live systems. Always de-energise live systems before installation or assembly work. Work on live systems may be carried out by trained electricians only. Always observe the relevant safety regulations. WARNING! Danger of accidents due to unpredictable machine contact due to non-functioning safety equipment. Never switch off or bypass the machine’s safety equipment (lock, safety door, etc.).
System overview 3. System overview 3.1 Measuring system IF59-30-A2 IF59-A2 NC EM30 1 x EM31 EM32 NC EM34 I/O SSI Fig. 3-1 Overview of compatible components (examples).
System overview 3.2 Description 6 4 1 5 (1) (2) (3) (4) (5) 3 7 8 9 2 Mode LED Status LED Battery LED Transmit LED Receive LED (6) (7) (8) (9) Fastening hole Connecting cable Seal insert O-ring 40× 2(NBR 70) Fig. 3-2 Device description RC66. 3.3 Display elements Mode LED Standby TC, Z-, ZX- – Probe 1 YE TC, Z-, ZX- – Probe 2 … Probe 6 DIGILOG, RG – Probe 1 … Probe 6 BG – Probe 1 … Probe 16 KOMflex – Probe 1 … Probe 16 Pairing Status LED TC, Z-, ZX- – Measuring device home position.
System overview Battery LED Battery is good. Pairing successful. Battery low. Pairing unsuccessful. YE No battery data. Pairing not yet performed. Receive LED Valid data. Invalid/faulty data. No data. Transmit LED Send data. YE Activate/deactivate. No data.
System overview 3.4 Technical data Protection class IP68 Operating voltage UB (stabilised DC voltage) 12…13V / 100mA via interface Signal transmission Radio Frequency band 2.4…2.5GHz Max. transmission power 0dBm Transmission range 15m – see 3.5 Area of work Min. bending radius cable 60mm (application: flexible) Max. cable length 50m Storage temperature -20 ... +70 °C Operating temperature +5 ... +50 °C 3.4.
System overview 3.5 Area of work 75° 60° 45° 30° 15° 90° 16 14 12 10 8 6 4 75° 75° 60° 60° 45° 45° 30° 30° 15° 15° 2 2 0° 0° 15° 0° 15° 30° 15° 30° 45° 30° 45° 60° 45° 60° 75° 90° 16 14 12 10 8 6 4 90° 60° 75° 75° 90° Fig. 3-4 Wireless communication range.
Mounting 4. Mounting 4.1 Selecting the installation position The installation position has no effect on other machines – see 3.5 Area of work. The measuring device is reached – see 3.5 Area of work. The receiver is optimally protected against coolant and flying chips. Test the desired installation position before installation. Use the drilling template included. 4.2 Mounting variants 4.2.1 Horizontally facing cable 5 4 1 2 3 1 2,5 mm (M3) – 1,3 N·m max. 3 mm (M4) – 3,0 N·m max.
Mounting 4.2.3 Front kit 2 4 1 3 3 mm (M4) – 3,0 N·m max. (1) Cover ring (2) 4× holding screws M4×25 (ISO 7380) (3) Machine wall (4) O-ring 40× 1.5(NBR 70) Fig. 4-3 RC66 – Installation with BLUM Front Kit. 4.3 Electrical connection The electrical connection is described in the installation instructions of the associated interface. 4.4 Device marking When using different BLUM measuring devices, colour marking of the devices can be helpful to prevent mix-ups.
Maintenance 5. Maintenance NOTICE Damage to the measurement components due to contact with corrosive liquids. Never use coolant containing solvents (acetone, alcohols, benzines, etc.). Only use coolant with a pH value in the range of 4.5…9.5. Never use cleaning agents containing acetone. Always exercise caution when using cleaning agents containing solvents (alcohols, benzines, etc.) or a high acidic/ alkaline pH value – avoid long periods of exposure.
Order numbers 6. Order numbers Use original parts and accessories by Blum-Novotest only. Front Kit RC66 143002 Heavy Duty Kit Protection spring 1m incl.
Shipping instructions / storage 7. Shipping instructions / storage NOTICE Damage to the device caused by improper packaging. Preferably send and store the measuring components in their original packaging. Package the measuring components in such a way that they are protected against impacts and contamination. Ensure that the measuring device is not deflected inside the packaging. Please complete this repair order, answering all questions in detail, and attach it to the system.
EC Declaration of Conformity 8.
Radio approval 9. Radio approval The label indicating the radio approval is attached to the device or included as a sticker – in this case, attach the correct sticker to the device. The device is compliant with standard IEEE 802.15.4a. European Union: – see 8. EC Declaration of Conformity Eurasian Economic Union: Japan: “This device has been granted a designation number by Ministry of Internal Affairs and Communications under „Ordinance concerning Technical Regulations Conformity Certification etc.
Service 10. Service Head office Blum‐Novotest GmbH Kaufstraße 14 88287 Gruenkraut, Germany Phone: +49 751 6008‐0 Sales sales@blum‐novotest.com Phone: +49 751 6008‐200 Service service@blum‐novotest.com Phone: +49 751 6008‐202 Homepage www.blum‐novotest.