EC - Declaration of Conformity We, Innovi Technologies Ltd of 31/F China Online Centre, 333 Lockhart Road, Wan Chai, Hong Kong declare under our sole responsibility that our product BLUETREK mini to which this declaration refers is in conformity with the appropriate standards EN300 328-02 EN301 489-17 EN301 489-01 EN50371 EN60950 Following the provisions of Radio and Telecommunications Terminal Equipment directive 1999/5/EC.
FCC/ Industry Canada Notice This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. In compliance with Industry Canada regulations, technical specifications have been provided in a declaration of conformity. This does not imply that Industry Canada approved the equipment.
English Before using your headset for the first time -You must charge it continuously for about 4 hours, until the red indicator light turns off. Please refer to the “Charging the BLUETREK® MINI” section of this manual. -Pair the headset with a mobile phone. Please refer to the “Pairing the BLUETREK® MINI” section of this manual. Introduction The BLUETREK® MINI headset is a wireless headset based on the Bluetooth® technology. It complies with Bluetooth® 1.
Please connect the charger to the headset and to the main. During the charge, the indicator light is red. The indicator light will turn off when the charge is complete. During subsequent charges, the charging should take approximately 3 hours. When you hear a low-tone beep in your headset at regular intervals, and the indicator light flashes in red, your headset needs to be recharged. Important: · If your headset is fully charged, the red indicator light will not turn on when plugging into the charger.
English Pairing the BLUETREK® MINI Before using the BLUETREK® MINI headset, you must pair it with your Bluetooth® mobile phone. Pairing is the process of linking 2 Bluetooth® devices, so that they can communicate. To initiate pairing: 1 Place the BLUETREK® MINI and your mobile phone within 0.3 meter (1 foot) from each other. 2 Switch on your phone and select its Bluetooth® discover mode (refer to the Bluetooth® mobile phone user manual).
Once the mobile phone detects the headset, a “BLUETREK MINI” message will be displayed. Follow the phone instructions to accept the pairing. The PIN code (or passkey) is 0000, then press “yes” or “ok”. BLUETREK MINI BLUETREK MINI BLUETREK MINI “0000” 5 For some phones, you may need to select “Connect” BLUETREK MINI Connect Assign short name Set as unauthorised Delete Select Cancel If pairing was successful, the indicator light will switch to blue and flashes slowly.
English Fitting lanyard 5 I BLUETREK MINI
Switching BLUETREK® MINI ON When your headset is off, press and hold the TALK button for about 5 seconds until the blue indicator light is on. A beep (2 tones) can be heard in the speaker. Release the TALK button. Switching BLUETREK® MINI OFF When your headset is on, press and hold the TALK button for about 7 seconds until the red indicator light is on. A beep (2 tones) can be heard in the speaker then release the TALK button. Making a call Mobile phone with voice recognition .
English Mobile without voice recognition . Make sure both the headset and the mobile phone are ON and in stand-by mode. . Dial the number on the phone keypad, after approximately 2 seconds the audio connection will be established. This function may not be available on some phones, please refer to the trouble shooting frequent asked questions in our website: www.bluetrek.com. to find out more. Answering a call When the headset rings, press once on the TALK button to take the call.
To mute the microphone during an active call During an active call, press and hold the VOL+ button for approximately 2 seconds. A periodic tone can be heard in the speaker when the microphone is muted. English Muting the microphone To end the mute function When the microphone is muted, press and hold the VOL+ button for approximately 2-3 seconds. The periodic tone will end. Transferring a call from BLUETREK® MINI to the mobile phone During an active call, double click on the TALK button.
English Fitting the Ergobud* 3 different sizes of Ergobud* are included in the pack to suit your ear size. You can adjust the Ergobud position that you feel the most comfortable. S M L To replace the Ergobud*, remove the speaker cover by pulling gently out from the speaker. Place the Ergobud* back onto the speaker by inserting the bottom part first.
When you hear a call waiting alert while you are on a call, press approx. 3 seconds on the TALK button to accept the second call and place the current call on hold. To switch between an active call and a hold call, press approx. 3 seconds on the TALK button. To end the active call and take the hold call, press once on the TALK button. This function may not be available, depending on your phone. However, you can always answer the second call from your phone keypad.
English Additional features with some phones Rejecting a call Press the TALK button for about 2 seconds to reject a call. Redial the last number When there is no incoming or active call, press the TALK button for about 3 seconds until you hear a beep. Troubleshooting guide The first thing you should do when encountering a problem that you cannot solve with this manual, is to switch off your headset and your mobile phone, and switch them on again.
English Guidelines for safe use Read those guidelines before using your headset. - The volume level of the Bluetooth® headset may vary, depending on your mobile phone. Before using your headset for the first time, adjust the headset volume to the lowest, then increase the volume gradually until you reach to an acceptable level. High levels of volume may result in hearing loss, avoid using the headset at high volume continuously.
GB Note on environmental protection: After the implementation of the European Directive 2002/96/EU in the national legal system, the following applies: Electrical and electronic devices may not be disposed of with domestic waste. Consumers are obliged by law to return electrical and electronic devices at the end of their service lives to the public collecting points set up for this purpose or point of sale. Details to this are defined by the national law of the respective country.