VXi B250-XTS User Guide
TABLE OF CONTENTS Welcome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Glossary . . . . . . . . . . . . . . .
WELCOME Congratulations on purchasing your new VXi office wireless product. This guide contains instructions for setting up and using your VXi B250-XTS Bluetooth® headset. B250-XTS Bluetooth Headset Features • Advanced noise canceling improves communication by cutting 95% of background noise. • Flexible microphone boom stays put for optimal sound quality. • Wideband HD Voice and audio for clearer conversations, increased productivity and safety.
SAFETY INFORMATION • A void hearing damage. Set volume at lowest comfortable level. If you experience ringing in your ears or voices sound muffled, stop using the headset. Avoid turning up volume to block noisy surroundings (it’s possible to adapt to volume that is too high). • Check with local and state laws regarding cell phone/headset usage while operating a motor vehicle. • Do not immerse any part of this product in water. • Plastic bags and small parts may cause choking if ingested.
WHAT’S IN THE BOX? 1. B250-XTS Wireless Headset with Leatherette Ear Cushion 2. Foam Ear Cushion 3. Spare Windscreen 4. USB Charging Cable 5. Quick-Start Guide (not shown) 6.
HEADSET OVERVIEW A. Multifunction Button (MFB) B. Indicator Lights C. Volume Up/Mute D. Volume Down E.
CHARGING THE HEADSET Connect the USB charging cord to the headset and the other end to a suitable USB charger. The MFB’s indicator light may turn green for several seconds while the headset determines the level of charge the battery is holding. Do not remove the headset from the charger. If the headset is not fully charged, the indicator will turn RED within a short period (less than 3 minutes). When the indicator turns green—and stays green—the unit is fully charged.
HEADSET CONTROLS Volume Increase: Quickly press and release the Volume Up/Mute button. Repeat until desired volume is attained. Volume Decrease: Quickly press and release the Volume Down button. Repeat until desired volume is attained. Microphone Mute/Unmute: While in standby or on a call, hold down the Volume Up/Mute button for 2 seconds until you hear a beep. A mute reminder will be heard every 10 seconds. Repeat button press to unmute.
PAIRING Pairing with a Phone Keep headset and phone no less than 3 inches and no more than 3 feet apart while pairing. Keep other Bluetooth devices at least 50 feet away, or turn them off. NOTE: The headset can be paired with up to 8 different devices but can only be connected to one at a time. It can only switch back and forth between 2 devices in Multipoint Mode. • T urn headset off.
PAIRING (continued) Multiple Device Pairing The B250-XTS can pair with up to 8 devices; however, only one device may be connected to the headset at a time, unless the headset is in Multipoint Mode (see page 13). To pair the headset with a Bluetooth cell phone or other Bluetooth device, such as a Bluetooth enabled computer, follow the instructions on pages 10 and 11 of this manual.
MULTIPOINT MODE Multipoint Mode allows you to pair and switch between two Bluetooth devices. Enabling Multipoint Mode • T urn the headset on. It will display a blinking red light and you will hear a voice prompt, “Power on.” • While pressing the MFB button, quickly press the Volume Up and Volume Down buttons at the same time, and then release all buttons. • You will hear 4 rising tones. • Once Multipoint Mode is active, shut the headset off.
PROXIMITY PAIRING Proximity Pairing enables the headset to find the closest “discoverable” phone. • Make sure the headset is powered on. • Hold the MFB down and quickly press the Volume Down button. • You should hear the voice prompt “Discovering” in the headset. • The headset lights should now be alternating red and blue. • The headset initiates pairing activity, and the user has to accept the incoming pairing invitation on the phone.
MAKING CALLS Making a Call If you have not paired the headset and phone together yet, you must do so. • Turn on your cell phone. Be sure the Bluetooth option is enabled on your phone (refer to your phone’s user guide for instruction). • Put headset on and properly position the microphone. To turn headset on, press MFB for 2-3 seconds. The headset will automatically attempt to connect with the last device it was paired or connected with.
ADDITIONAL FUNCTIONS NOTE: Your cell phone must support the following functions (consult the phone owner’s manual). Last Number Redial To re-dial the last number that was dialed from the cell phone, press and hold the Volume Down button for approximately 1 second. A beep will be heard and the phone will redial the last number. Reject a Call To reject an incoming call, press and hold the MFB for 2 seconds.
RESET PAIRED DEVICES LIST The headset must be on to perform this function. To reset the headset’s internal paired devices list, hold the headset near your ear. Press and hold the Volume Up and the Volume Down buttons simultaneously for approximately 5-6 seconds until two low tones are heard. This procedure may be necessary if the headset will not pair or connect to a device. NOTE: Pairing information for devices previously paired with the headset will be lost.
FUNCTIONS & INDICATORS TABLES Function Button/Duration of press LED Indicator Audio Indicator Voice Indicator Power On MFB / 2-3 seconds Red light flashes Two rising tones “Power on” Power Off MFB / 4-5 seconds All lights go off Two falling tones “Power off” Enable Pairing Mode MFB / 5-15 seconds Red & blue lights flash alternately NONE “Discovering” Volume Up Volume Up / quick press NONE Single tone NONE Volume Down Volume Down / quick press NONE Single tone NONE Mute (On/Off)
FUNCTIONS & INDICATORS TABLES (continued) Function Button/Duration of press LED Indicator Audio Indicator Voice Indicator Enable Multipoint Mode MFB / Vol Up & Vol Down (quick press) NONE 4 rising tones NONE Disable Multipoint Mode MFB / Vol Up & Vol Down (5-6 seconds) NONE 4 falling tones NONE Connected A2DP NONE Double flashing blue MFB NONE NONE VXi B250-XTS User Guide PAGE 17
VXi Corporation | 271 Locust Street, Dover, NH 03820 USA Toll-Free (USA): 800-742-8588 | Phone: +1 603-742-2888 vxicorp.com © 2016 VXi Corporation. All rights reserved.