VXi BlueParrott B350-XT User Guide ®
TABLE OF CONTENTS Safety Information ..........................................3 Package Contents ..........................................4 Glossary of Terms ............................................5 Headset Overview ..........................................6 Charging the Headsets ....................................7 • Battery Power Indicators • Operation While Using the Charger/Adapter Getting Started ................................................9 • On/Off/Standby • Pairing with a Phone i.
SAFETY INFORMATION IMPORTANT SAFETY NOTE: Prolonged exposure to high volume levels can damage your hearing. To avoid injury, set the volume to the lowest comfortable level. If you experience ringing in your ears, or voices sound muffled, stop using the headset. Avoid turning up the volume to block noisy surroundings. It’s possible for your ears to adapt to volume that is too high, and this could result in permanent hearing damage without any noticeable discomfort.
PACKAGE CONTENTS 1. B350-XT™ Headset with Leatherette Ear Cushion 2. Spare Foam Ear Cushion 2 1 3. Spare Microphone Windscreen 4. USB Charging Cable 5. AC/DC Wall Charger 3 6. Auto (DC) Adapter 7. Quick-Start Guide* 8. Warranty and Compliance Document* *Not pictured. 5 6 4 Images are not shown to scale.
GLOSSARY OF TERMS • On: Headset is on, but there is no connection to the phone (red light will flash). • MFB: Abbreviation for “Multifunction Button.” • Multipoint Mode: Multipoint Mode allows you to connect and switch between two Bluetooth devices. • Paired: Two Bluetooth devices agree to communicate with one another. • Standby Mode: Headset is on, Bluetooth link is active, and the user is not on a call (blue light will flash).
HEADSET OVERVIEW A. Flexible Microphone Boom (White dot indicates "talk" side.) B. Volume Down C. Volume Up/Mute D. Multifunction Button (MFB) E. Indicator Lights F.
CHARGING THE HEADSET Connect USB charger cord into the headset’s USB charging port. If the headset is not fully charged, the indicator will turn red. When the indicator turns blue and stays blue the unit is fully charged. A fully discharged battery will need approximately 3.5 hours to achieve a complete charge.
CHARGING THE HEADSET (continued) Operation While Using the Charger/Adapter The B350-XT headset will operate from battery power or from the AC or DC charger/adapter. NOTE: Do not attach the charger mid-call. This will cause the headset to reset, and the call will be sent back to the phone. When the headset is operating from the battery, all indicator lights and sounds will function as described in this guide.
GETTING STARTED On/Off/Standby Turn Headset On: Hold down the MFB for approximately 2-3 seconds until you hear a voice prompt, “Power on.” The red light will flash once every second. Turn Headset Off (conserves battery power): Hold down the MFB for approximately 4–5 seconds until you hear a voice prompt, “Power off.” A red light will flash 4 times and the headset will turn off.
GETTING STARTED (continued) Manual Pairing Placing Headset into Pairing Mode With the headset powered off, press the MFB until the light rapidly flashes blue and you hear the audio prompt “Power on.” Keep holding the MFB for approximately 10 seconds until you hear “Discovering.” Headset will be visible for pairing to devices for 120 seconds. Pairing to a Cell Phone 1. Make sure that other Bluetooth devices are turned off or out of range. 2. Place headset into pairing mode. 3.
GETTING STARTED (continued) Wearing and Adjusting the B350-XT To get the best performance from our noise-canceling technology, position the microphone near the corner of your mouth. Positioning is important; small adjustments in microphone placement can improve performance. 1. Place the headset on your head. 2. Position the speaker directly on your ear. You can slide the headband in or out of the side support for proper fit. 3.
GETTING STARTED (continued) Making/Taking Calls The headset must be on and connected with your phone. Making a Call 1. Dial the desired number on your phone. You will hear the call in the headset. 2. To end the call, press the MFB once. The call will end and the headset will enter standby mode. Answering a Call 1. When you receive a call, you will hear ring tones in the headset. Press the MFB once to answer the call. 2. To end the call, press the MFB once.
PARROTT BUTTON As provided from the factory, the headset’s Parrott Button provides an easy way to mute the headset. However, you can also configure the button for other functions, such as a speed dial button for a dedicated phone number, or to launch a particular application on your phone. To change the Parrott Button functions, you will need to download an app for your phone (Android or iOS) or to your PC. Go to vxicorp.com/parrott for updates and more information.
ADVANCED FEATURES AND FUNCTIONS Multiple Device Pairing and Multipoint Mode The B350-XT has pairing memory for up to 8 devices. The headset can also use Multipoint Mode, which means that it can be connected to two Bluetooth devices at the same time. You do not have to do anything to enable Multipoint Mode. Using the B350-XT in Multipoint Mode 1. To use the headset in Multipoint Mode, first make sure the headset is paired with both your devices. 2.
ADVANCED FEATURES AND FUNCTIONS (continued) Additional Features and Functions i. Last Number Redial To redial the last number that was dialed from the cell phone, press and hold the Volume Down button for approximately 1 second. A beep will be heard and the phone will redial the last number. ii. Call Waiting/Rejecting a Call If you are on an active call and a second call comes in, you will hear a low tone notification in the headset.
ADVANCED FEATURES AND FUNCTIONS (continued) v. Muting The Parrott Button will act as a mute by default, unless configured for another function. The Volume Up button will also function to control mute. • A quick press of the Parrott Button while on a call will engage the mute. (Unless otherwise configured) Press again to unmute. • To use Volume Up to mute the headset microphone while on a call, press and hold the Volume Up button for 1-2 seconds. To unmute, press and hold the button again for 1-2 seconds.
ADVANCED FEATURES AND FUNCTIONS (continued) Resetting Headset’s Paired Devices List This will reset or clear the headset’s internal paired devices list. The headset must be on to perform this function. 1. Power on the headset. It does not matter if it connects to any devices. 2. Hold the headset near your ear and press and hold the Volume Up and the Volume Down buttons together for approximately 6-10 seconds until two low tones are heard. 3. Power off the headset.
FUNCTIONS & INDICATORS TABLES Standby Mode Functions Function Button/Duration of Press Power On LED Indicator Audio Indicator Voice Indicator MFB (1-2 seconds) 3 fast blue flashes NONE “Power on” Power Off MFB (2-3 seconds) 4 fast red flashes NONE “Power off” Enable Pairing Mode MFB (5-15 seconds) Alternating red and NONE blue flash Volume Up Volume Up (quick press) NONE 1 short tone NONE Volume Down Volume Down (quick press) NONE 1 short tone NONE Phone Voice Control (Start/End)
FUNCTIONS & INDICATORS TABLES (continued) Standby Mode Functions (continued) Function Button/Duration of Press LED Indicator Audio Indicator Voice Indicator Enable LEDs Volume Up/ Volume Down (quick press) LEDs active 1 short tone NONE Reset Paired Devices Volume Up/ Volume Down (5-6 seconds) NONE 2 low tones NONE Enable Multipoint Mode MFB/Volume Up & Volume Down (quick press) NONE 4 rising tones NONE Disable Multipoint Mode MFB/Volume Up & Volume Down (3-4 seconds) NONE 4 falling to
FUNCTIONS & INDICATORS TABLES (continued) Standby Mode Functions (continued) Function Button/Duration of Press LED Indicator Audio Indicator Voice Indicator Establish Service Level Connection MFB (Quick Press) Fast blue flash 1 long tone “Your headset is connected” Start Proximity Pairing MFB & Volume Down (quick press) Alternating red and Long low tone blue flash every 5 seconds for 60 seconds Proximity Pairing Timeout NONE NONE VXi BlueParrott® B350-XT User Guide “Discovering” 2 short to
FUNCTIONS & INDICATORS TABLES (continued) In-Call Functions Function Button/Duration of Press LED Indicator Audio Indicator Voice Indicator Volume Up Volume Up (quick press) NONE 1 short tone NONE Volume Down Volume Down (quick press) NONE 1 short tone NONE Mute (On/Off) Parrott Button, unless otherwise configured (quick press) NONE 1 tone NONE Mute (On/Off) Volume Up (1-2 seconds) NONE 1 tone NONE Mute Reminder NONE NONE 1 tone NONE (every 10 seconds) Answer a Call MFB (quick
FUNCTIONS & INDICATORS TABLES (continued) In-Call Functions (continued) Function Button/Duration of Press Reject a Call* MFB (1-2 seconds) NONE LED Indicator Audio Indicator Voice Indicator 2 falling tones NONE *Sends call to voicemail (if available) Transfer Audio Volume Down (1-2 seconds) NONE (LEDs go out 1 long tone until call ends, or audio transferred back to headset) NONE Incoming Call Hold MFB (2 quick presses) NONE NONE NONE Accept Held Incoming Call MFB (quick press) NONE NONE
FUNCTIONS & INDICATORS TABLES (continued) Notifications Notification Button/Duration of Press LED Indicator Audio Indicator Mute Reminder NONE NONE 1 tone NONE (every 10 seconds) Headset Connects to device NONE Blue light, fast flash NONE “Your headset is connected” Disconnect from Device NONE Red light, slow flash NONE “Your headset is disconnected” Out of Range (Link Loss) NONE Red light, slow flash 1 short tone NONE Low Battery NONE Red light, 2 fast flashes NONE “Battery low”
SPECIFICATIONS Mechanical Specifications Electrical Specifications Headset Weight 2.72 oz. (77 g) Battery Type Li-ion rechargeable (not user-replaceable) Wearing Style Over-the-head Talk Time 24+ hours Microphone Boom Flexible gooseneck boom Standby Time Up to 500 hours Receiver Specifications Charging Time 3.5 hours SPL 123 dB ± 3 dB at 1 mW Bluetooth Specifications Impedance 32 Ω ± 15% @ 1 kHz Bluetooth Version Bluetooth 4.
VXi Corporation | 271 Locust Street, Dover, NH 03820 USA Toll Free: (800) 742-8588 | Phone: (603) 742-2888 vxicorp.