PLACEHOLDER COVER IMAGE FINAL IMAGE TO MATCH BOX ARTWORK
Speak to me Introduction The S4 speakerphone is the first true handsfree voice controlled Bluetooth car speakerphone. There is no need to take your hands off the wheel or your eyes off the road to use the S4. Simply say the trigger phrase BlueAnt Speak To Me™, and the S4 will be ready for your voice commands.
Charge Your S4 Your S4 has been given an initial partial charge to get you started, but for best results we recommend you charge it using the supplied USB cable and adaptor until the battery indicator light turns solid white. Blu eA nt >> You should charge the S4 whenever it announces Battery: Very Low, or when the battery indicator turns solid red. Battery Indicator ON F OF >> A full charge takes about 3-4 hours. >> During charging, the battery indicator light flashes red.
To use the S4 you need to pair it with your phone. Once paired, they will reconnect automatically in future. 1. Slide the power switch on the side of the S4 to the ON position. 2. If this is the first time you have used the S4 it will go straight to pairing mode. You can tell that the S4 is in pairing mode because the S4’s indicator lights will alternately flash blue and red, and the voice prompts will talk you through the pairing process.
announce that it cannot transfer the contacts automatically. See “Uploading your Phonebook Contacts to the S4” on page 13 for details on how to copy the contacts manually. 5. Once the phonebook upload is complete, you are ready to go. Install the S4 in your Car 1. Slide the sun visor clip onto the edge of the car sun visor 2. Attach the magnetic back of the S4 to the fixed sun visor clip.
Your S4 is designed to be a true handsfree device. Simply say the trigger phrase BlueAnt Speak To Me and the S4 will be ready to receive your voice commands. 1 BlueAnt: Speak To Me Handsfree Trigger Indicator BlueAnt 2 ENGLISH Using the Handsfree Trigger Say A Command BlueAnt When the S4 asks you to Say A Command, say one of the voice commands loudly and clearly. Please note: The handsfree trigger only works when the solid green handsfree trigger indicator light on the front of the device is on.
Handsfree Trigger Battery Saving Mode Using the trigger gives you true handsfree operation, but because the S4 is always listening for your voice this feature reduces the device’s battery life. If you want your S4 to run for longer between charges, you can use the “battery saving mode”. In this mode the S4 only listens for 2 minutes after the last action. Once the 2 minutes are up, the green indicator light goes out and the S4 stops listening.
The volume bar is touch sensitive. To adjust the volume, swipe your finger to the left or the right along the top of the S4. You can also adjust the volume by holding down the - and + buttons. ENGLISH Adjusting the Volume Making Phone Calls You can use your voice to make calls.
Taking Calls When the phone rings, you can answer the call with your voice: wait for the prompt to ask you if you want to take the call, and then say Answer or Ignore. You can also answer or ignore a call by tapping the the middle of the volume controls: button in >> Tap once to accept the call. >> Double tap to reject the call. During a call, tap the button to end the call.
When you want to do something, just say BlueAnt Speak To Me, wait for the S4 to ask you to Say A Command, and then say one of the following commands: >> Am I Connected? — The S4 will check if your phone is connected, and attempt to connect if it is not. ENGLISH Full List of Voice Commands >> Call Back — Calls back the last incoming call received on the S4. >> Cancel — Cancels the current operation. >> Check Battery — Tells you the battery level on the S4 and the connected phone.
>> Pair Me — Puts the S4 into pairing mode. Any connected phone will be disconnected. >> Phone Commands — Activates your phone’s voice dialing feature (if available). Depending on your phone model, you may need to record voice tags on the phone to use this feature. >> Redial — Redials the last outgoing call made on the connected phone. This is the last outgoing call made on the phone, regardless of whether the phone was connected to the S4 at the time.
Your S4 uses Text To Speech technology (TTS) to read out the name of the person who is calling you. To do this, the S4 needs to store a copy of your phonebook contacts. ENGLISH Uploading your Phonebook Contacts to the S4 Automatically Transferring your Contacts to the S4 When you pair your phone with the S4 it will attempt to copy the contacts from your phone automatically. Depending on the size of your phonebook, this may take some time.
3. Select the option on your phone to send the contacts via Bluetooth, and select the S4 from the list of available Bluetooth devices. Updating your Contacts on the S4 If you add contacts to your phone, or rename one of your existing contacts, then you will need to update the contacts on your S4 by doing the following. 1. Say BlueAnt Speak To Me, and wait for the S4 to ask you to Say A Command. 2. Say Update Phonebook. 3. The S4 will attempt to copy your phonebook automatically.
ENGLISH your phone) and the audio will automatically transfer to the S4. If the phone rings the audio will pause automatically. >> Tap the button to accept the call >> Double tap the button to ignore the call The audio will resume when the call ends. If you want to exit A2DP streaming mode to do something else, tap the Command.
Multipoint: Using 2 Phones with the S4 The S4 can store pairing information for up to 4 Bluetooth devices. Up to 2 devices can connect to the S4 at the same time: if either phone rings, you can answer it with the S4. Use the “Pair Me” command to put your S4 back into pairing mode to pair another phone. Any currently connected phone will be disconnected during pairing, so you will need to reconnect afterwards.
Multiple Calls (Call Waiting) ENGLISH on which phone is the current primary phone. This is different to Call Back, which calls a number stored in the S4. Call Back will always call the last incoming call received on the S4, regardless of which phone received the call. If you receive an incoming call while you are already on a call, and your phone and network both support call waiting, then you can use the S4 buttons to either end the current call or put it on hold and take the new call.
If you are using multipoint, you can also use the same controls to switch between calls on both phones. Switching the S4 On and Off To switch the S4 on or off, use the hardware power switch located on the side of the device. >> Slide the switch to the ON position to use the S4 in handsfree trigger mode. >> Slide the switch to the position to use the S4 in battery saving mode. In this mode the S4 will only listen for the trigger phrase for 2 minutes after you do something.
Reference: Button Functions >> Standby Mode means connected to a device but not on a call. ENGLISH You must register your product online at register.blueantwireless.com for access to firmware upgrades. >> Idle Mode means the S4 is on but not connected to any devices.
S4 Function Button Activate phone voice dialing (if supported by your phone) Tap the Enter pairing mode Hold the seconds Answer a call Tap the button Ringing End a call Tap the button Active call Reject a call Double tap the BlueAnt When Idle/Standby (only when the handsfree trigger is on) button button for about 6 button Hold active call and switch to incoming or held call Hold + button for 1 second End active call and answer a new incoming call Hold - button for 1 second BlueAnt
Button When Reset the S4 Hold + and - for 6 seconds Idle Troubleshooting ENGLISH S4 Function I Cannot Upload my Phonebook to the S4 In order to copy your phonebook to the S4, your phone must support either the Phonebook Access Profile (PBAP), AT commands, or the Object Push Profile (OPP). If your phone does not support any of these Bluetooth profiles, then you will not be able to copy your contacts to the S4. When you receive a call, the S4 will read out the caller’s number instead.
The S4 Does Not Announce the Caller’s Name The S4 will only announce the name if the caller’s name and number are stored in your phonebook and have been copied to the S4 (your phonebook is automatically copied across when you pair your phone). If you add a number to your phonebook after pairing, then the S4 will not read out the name associated with this number unless you use the Update Phonebook command to update the phonebook details on the S4.
The S4 Does Not Respond to “BlueAnt Speak To Me” The trigger only works when the green handsfree trigger indicator light is on. If the green light is off, tap the ENGLISH Each number stored in your phone counts towards this limit. For example, if you have a business, home, and mobile number stored for one of your contacts, then this counts as 3 separate numbers. button to activate voice control, instead of saying the trigger phrase.
phone’s list of “trusted devices”. My Phone Prompts me for a Code when I Pair the S4 Enter the code 0000 (four zeros). The S4 Switches Itself Off If the battery gets very low, the S4 will switch itself off automatically. You should charge the S4 using the supplied USB cable and adaptor.
>> Speak louder than any background noise. >> Try changing the S4’s sensitivity level. This setting determines how precisely the words that you say need to match the speech patterns that the S4 has been configured to recognize. You can change it by using the Sensitivity Level command.
>> If the battery level drops to very low, then the S4 will play a low battery sound and automatically switch itself off. >> If you take the S4 out of range of your phone, then it will play a sound to indicate that it has lost the connection to your phone. >> The S4 plays a beep when you end a call. >> The S4 plays a beep when you adjust the volume to the maximum or minimum volume level. >> The S4 plays a call waiting sound if you receive an incoming call while you are on a call.
If you are having problems with the S4, you can reset it and start again. Resetting the S4 will clear all the stored pairing settings on the S4, delete any stored contact details and put the device back into pairing mode. ENGLISH Resetting the S4 To reset the S4: 1. Delete any existing pairing information from your phone and turn it off and back on again to refresh the phone memory. 2. Make sure the S4 is switched on but not connected to any phones. 3.
Help and Support If you are having trouble getting the S4 to work, please visit www.blueantwireless.com for online help, support, and troubleshooting tips. You can also follow the links to register your S4 for access to firmware upgrades. Please call us before returning the S4 to a store and we will help you through any difficulty you may have.
By using this product, you are agreeing to BlueAnt’s terms and conditions, available at www.blueantwireless.com and on the supplied warranty information card. Please protect your ears. All BlueAnt headsets are designed to reach volumes of up to 100 decibels. Prolonged use at high volumes may affect your hearing capacity and may result in noise induced hearing loss (NIHL). Please read the enclosed safety card for information about the safe use of BlueAnt products.
BlueAnt w w w. b l u e a n t w i re le s s . co m Australia 1300 669 049 USA 1866 891 3032 New Zealand 0800 443 122 Email Enquiries customercare@blueantwireless.
Important Safety Information Please read this entire document carefully. it Contains important information About the safe use of BlueAnt devices Protect Your Ears All BlueAnt headsets are designed to reach volumes of up to 100 decibels. Prolonged use of a BlueAnt device at high volumes may affect your hearing capacity. Using for extensive time periods may result in noise induced hearing loss (NIHL).
• Get to know your BlueAnt device and its features such as speed dial and redial. These features help you to place your call without taking your attention off the road. • Position your mobile device within easy reach. Be able to access your mobile device without removing your eyes from the road. If you receive an incoming call at an inconvenient time, if possible, let your voice mail answer it for you.
dial and your s your mobile an incoming wer it for you. ssary, ns. Rain, sleet, ember that be g and the road. se of fire, e local ssistance ng no serious o one appears nce or nt. To ensure quality tructions. or console ket, or take he ahrenheit), ot day the n the outside he grees d to humidity, ause your aners to clean stances a an it. arger for long ntinued to BlueAnt does let, adaptor k advice from nd placed in a er. power e it and that the adapter voltage is suited to the local power supply.
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
