4)$!,¬7!6% ) '¬POOL PUMP INSTRUCTION MANUAL S MP PU READ THIS MANUAL CAREFULLY ¬¬¬BEFORE USING YOUR PUMP 8258
PUMP PARTS BREAKDOWN REF # 1 2 3 4 5 6 7 8 9 10 11 12A 12B 12C 13 14 15 16 17 18 19 20 2 Order # NEP2254 NEP2255 NEP2256 NEP2257 NEP2258 NEP2259 NEP2260 NEP2261 NEP2262 NEP2263 NEP2264 NEP2265 NEP2266 NEP2267 NEP2268 NEP2269 NEP2270 NEP2271 NEP2272 NEP2273 NEP2274 NEP2275 Mfr # AC 23248 AC 23280 AC 23299 AC 23337 AC 23345 AC 23388 AC 23418 AC 23450 AC 23469 AC 23485 AC 23493 AC23507 AC 23515 AC 23523 AC 23531 AC 23558 AC 23566 AC 23574 AC 23582 AC 23590 AC 23612 AC 23639 Description Lid Knobs Strainer L
IMPORTANT SAFETY INSTRUCTIONS NOTE All wiring should be done by a qualified electrician in accordance to the National Electric Code and all Local Codes and ordinances. When installing and using this electrical equipment, basic safety precautions should ALWAYS be followed. READ AND FOLLOW ALL INSTRUCTIONS WARNING 1. To reduce the risk of injury, do not allow children to use this equipment 2. Connect only to a grounding type receptacle that is protected by a ground fault circuit interrupter (GFCI). 3.
OPERATION AND MAINTENANCE PUMP LOCATION 1. Locate the pump on a level surface as close to the pool as practical. Consult local codes for minimum distances between pool and pump if applicable. 2. The connection plumbing (hose or rigid pipe) should be direct and as free from turns and bends as possible. Take care not to kink flexible hose. Elbows and other fittings greatly increase friction losses. 3. Place pump on a solid foundation / base which provides a rigid and vibration free support. 4.
PUMP INSTALLATION 1. When connecting plumbing fittings to the pumps threaded ports, it is recommended that thread seal tape (Teflon tape) be used. If the suction (intake) connection is not sealed correctly the pump will not prime properly and will pump only small volumes of water or no water at all. 3. Suction and discharge lines should be independently supported at a point near the pump to avoid strains being placed on the pump. 4.
DO NO BLOCK SUCTION 1. Pump suction is dangerous and can trap and drown or disembowel bathers. 2. Blocking suction with body may cause severe and/or fatal injury 3. Do not operate swimming pools, spas or hot tubs if a suction outlet cover is missing, broken or loose 4. Suction outlet must be replaced if cracked, broken or missing. 5. All suction outlets must have correctly installed screw fastened covers in place. WARNING RISK OF ELECTRICAL SHOCK 1.
TROUBLE SHOOTING GUIDE PROBLEM POSSIBLE CAUSE Pump will not Prime Motor Does Not Run Low Flow Suction Air Leak Make sure see thru lid and gasket are clean, lubed and tightened. Tighten all hoses and pipes on the suction side of the pump. Be sure water level in the swimming pool is high enough to flow through skimmer. Be sure skimmer port is not plugged or blocked. No Water in Pump Make sure strainer tank is full of water Closed Valves or Blocked Lines Open all valves in system.
ATTENTION LICENSED ELECTRICIANS STANDARD WIRING FOR 220V — See Motor Label for Details — If you are connecting your Pump to a 220V power source follow these simple directions.
ATTENTION LICENSED ELECTRICIANS STANDARD WIRING FOR 110V — See Motor Label for Details — If you are connecting your pump to a 110V power source follow these simple directions. Remove the rear housing cover to expose the electric connection plate 1 Move the white wire (not your power cord white) —the short white wire inside the motor housing- from the current location to the clip pin located in the center of the connection plate.