Pager and Charger Guide Part Number 321032B4 Premises Pager System® CommPass® Pagers GuestPass™ Pagers MediPass™ Pagers ShopperPass™ Pagers 34 34 7 18 34 34 1
Introduction Introduction: Congratulations on your purchase of the JTECH Paging System. Please take a few minutes to review this manual prior to installing and operating your system. Please inspect the System upon receipt. If the contents appear to be damaged, notify the shipper immediately to file a claim and notify JTECH Customer Care. If any component is missing, please contact JTECH Customer Care.
L W Charger Dimensions/Weight: H LxWxH 7.3x 6.9x 13.1” (184x176x333mm) Weight (Empty) 6.6lbs (3.0Kg) Weight (With 20 Pagers) 11.0lbs (5.0Kg) Multiple Chargers: H L A single Charger can hold up to 20 Pagers. Combine two or three Chargers using the optional Jumpers and 7.3A Power Adapter. Mounting Chargers: Chargers can be wall or counter top mounted using the supplied Mounting Plate. Wood screws are include for table or shelf mounting.
Connecting Power: 1. Insert the Power Adapter plug into the jack at the bottom of the Charger. Power Adapter Plug Charger Jack 2. Connect the Power Adapter to the Power Cord. Connecting Power to the Charger Charging Rack Adapter Power Cord 3. Plug the Power Cord into a 120VAC outlet. 4. The green LED on the Charger will light (ON). 120VAC Outlet 5. 4 Once the Charger is ON, the Pagers can be inserted.
Charging Pagers: Pagers are turned OFF for shipment from JTECH. When first received, Pagers are to be charged for a minimum of 3 hours prior to use. This first charge will also turn ON the Pagers. To charge: Insert Pagers into the empty Charger locations. 2. Once in the powered (ON) Charger, each Pager’s LED will light: 3. The LED color indicates charging condition. Flashing yellow light = Battery charge very low. Charge needed. Do not use the Pager.
Paging Using a Desktop Transmitter: 1. Remove the Pager you wish to page from the Charger. 14 5 15 6 3 3 3 3. The Pager LED in the front of the Pager will continue to flash every 3-4 seconds to confirm the Pager is ON and ready to accept a page. 3 Paging Using a Desktop Transmitter 3 2. The Pager will flash and vibrate to confirm it is ready for use. 16 7 4. Enter the number of the Pager you wish to page on the Transmitter or Remote Keypad. 5. Press # to send the page.
1. Remove the Pager you wish to page from the Charger. 14 5 5 15 6 3 3 2. The Pager will flash and vibrate to confirm it is ready for use. 16 7 3 3 3 3. The Pager charge LED will continue to flash, confirming it is ready to receive a page. 4. Pick up the telephone and listen for the dial tone. 5. Dial the telephone number that has been assigned to the Transmitter. 6. Listen for a beep from the telephone that confirms the Transmitter is ready. 7. Within 8-10 seconds, use the telephone keypad: a.
Replace Inserts: 1. Insert the KEY into the slots on the end of the Pager, until the Clear Plastic Cover unlocks. 5 Replacing Pager Inserts 34 34 5 2. Remove the Clear Plastic Cover and Insert. 34 34 3. Replace the Insert and “snap” the Clear Plastic Cover back into place.
Blank Inserts: Blank Promotional Sheets can be ordered from JTECH as needed. Sheets contain eight Inserts per sheet and perforated for removal. Sheets are white in color and can be printed on using a standard printer. Custom Inserts can also be professionally printed (call your JTECH sales representative for more details). Blank Inserts 11” (279.4 8 1/2” (215.9m 3.90” (99.1mm) 0.12” (3.05m) 0.30” (7.6mm) 0.70” (17.8mm) 1.05” (26.7mm) Cut Out 15.0”RTyp. 1.25”R Typ. (31.7mm R) CL 1.
Replacing the Battery: Batteries that no longer charge properly or have a reduced operating time can be replaced by the user. Replacement battery packs can be ordered from JTECH. To replace: 5 34 6 1. Insert the Key into the slots on the end of the Pager until the Clear Plastic Cover unlocks. 5 Replacing the Battery 34 6 2. Remove the Clear Plastic Cover and Insert. 6 6 3.
6 Unplug the battery from the Pager. 5. Dispose of the Nickel Metal Hydride battery pack at any retail department or home improvement stores that recycles rechargeable batteries. 6. Plug the new battery pack into the Pager. 7. Move any excess wire to the into the compartment’s left side while inserting the battery into the Pager. Battery wires must be on the left side of the Pager and not under the battery to assemble the pager properly. 8. 9. Replacing the Battery 4.
SYSTEM WARRANTY JTECH Communications, Inc. warrants its equipment to be free from defects in materials and workmanship for a period of one year. Its obligation under this warranty is limited to repairing or replacing, at its own sole option, any such defective products. Products must be returned with transportation charges prepaid. All warranty returns must also include a JTECH-issuesd RMA number, clearly displayed on the interior and exterior of the package(s).