CS-65 6.
IMPORTANT READ CAREFULLY BEFORE USE KEEP FOR FUTURE REFERENCE Attn: users. We are highly appreciated for your using CS-65 shredder. Read this operation manual carefully before attempting to assemble or operate the machine. The power unit used for this shredder is type JF200. Please read the attached engine manual for detail information of JF200. I. Warning & Symbols: To adjust the revolution speed of engine. The rabbit direction for speeding up and the tortoise direction for slow down.
I. Safety Warnings: Be extremely cautious to rotating blade in machine. 1. Never allow hand, foot, or any part of body enter hopper. 2. Never place hand, foot or any part of body closed to discharge opening while machine in operation. 3. Do not peer into hopper or discharge opening when the machine is running. 4. Never allow metal objects or something similar into machine. 5. Never allow children to operate machine. 6. Never operate your shredder-chipper under the influence of alcohol, drugs, or medication.
2. Attaching front foot to the basic machine. See picture 2. 1 2 3 4 5 2.1. Remove the nuts from bolts 1, 2, remove the bolts and pipe spacer. 2.2. Forward the parts box to make the long pin 3 clear. 2.3. Pull the discharge hopper out of the parts box and align the holes 1,2. 2.4. Hitch front foot 5 to the side board of the parts box and align the mounting holes with holes 1,2. 2.5. Put the pipe spacer that was removed in step 1 back in place.
nut. 3.5 Reassemble the pipe spacer and the long bolt 7and secure it tightly with gasket and nut. Then screw the nut tight in 6 place. 4. Attaching the chipper tube to the basic machine. 1 2 3 4.1. Put the chipper tube 2 in place on the side of the basic machine. Align the three mounting holes in the flange with three holes around place 1. 4.2. Secure the flange with gaskets and nuts M8. Make sure the chipper tube has no deflection before tighten the nuts. 5. Mounting the discharge grid 5.1.
9.3. Open the cover and pull the dipstick out. See picture 6. Gasoline 10W-30 and 5W-30 are available. Do not fill closer than 10mm to 15mm from the top of the fuel tank. dipstick cover 9.4. Refer to “starting the engine” for the instruction of adding fuel. III. Safety Instructions i. Training Make sure to fully understand the owner’s manual before attempting to operate the machine. ii. Preparation 1. Put the machine securely in a level surface. 2. Keep the operator area clear of other objects. 3.
4. Do not allow hands or any other parts of the body or clothing inside the feeding hopper, discharge chute, or other rotating parts. 5. Do not touch the muffler in operation since the temperature of muffler surface is so high that people will be burned. 6. Keep proper balance and footing at all times. Do not overreach. Never stand at a higher level than the base of the machine when feeding material into it. 7.
chipping tube for chipping by the rotating blade. 2. Some side shoots and branches may have to be trimmed from the main stalk before chipping. 3. Shorts stubs of branches may be pushed through the chipper section with next branch, never use hand. 4. Last branch is pushed inside of the tube by some tools like wood stick. Never try by hand. 5. Never push the small branches by hand, use wood stick instead. 6. When feeding branches, be certain that thicker branches should be pushed more slowly than thin ones.
4. Sharpen the blade. ● If the blade is struck a break by metal or stone or some hard subjects, please sharpen the break lot at first. ● Avoid changing the blade color and anneal when sharpening the blade. ● It may result in a breach on the edge if you overexert. ● Knifepoint angle should be kept in 45-40 degree. ● Two pieces of blade should keep the same weight as each other. They will shake if there is much difference between weight. 5.
SPECIFICATION Main dimension: L x W x H Net weight Fuel tank volume Oil tank volume Max. cutting speed Type of engine Engine manufacturer Engine type Carburetor type Type of carburetor Starter Spark plug Magneto Displacement Max. shaft brake power Max. engine speed Fuel consumption: Fuel consumption at max. engine power Specific fuel consumption at max. engine power Sound pressure level (Annex F of EN 13683) Sound Power level (2000/14/EC) inch lbs Gal Qt /min 30*29*45 154 0.95 0.