WS90t Features: ▪ Multifunction remote control – with Track Fwd/Back/Pause/Play feature. ▪ Range up to 25 meters ▪ No interference or delays – audio latency 18ms (max) ▪ RF Band 2.
What's in the box? Box A. 2 x Floor-Stand Speakers Box B. 2 x Power Cable 1 x Transmitter 1 x 3.5 – 3.5 Audio Cable 1 x USB – USB Mini Cable 1 x Optical – 3.5 Cable 1 x USB Adapter 1 x Remote Control 1 x 3.5-RCA Cable ? Box C.
WS90t Operating Instructions Thank you for choosing Blue Aura The flagship product of the Blue Aura Performance Series, WS90t has been developed using the latest advances in wireless technology, the operating frequency (2.4GHz) is not prone to interference from other wireless devices and the effective signal range is 25 metres. Both loudspeakers are fitted with active amplifiers equipped with high quality audio components aiding delivery of the audio signal.
This symbol indicates a safety warning This symbol indicates an advisory warning Once connected to the mains supply, never attempt to remove drive units or rear amplifier panels. Do not use these loudspeakers if defective and if for any reason they are found to be defective, unplug from the mains supply. Only use the supplied power cables and USB power adapter and replace immediately if damaged. Should you have any problems please contact your Blue Aura Distributor. www.blueaura.co.
Getting Started Unpacking your loudspeakers and attaching the plinth. WS90t is supplied with a plinth which must be attached to ensure loudspeaker stability.
1. E 2. Before unpacking, ensure a clean soft but stable surface is available to place the loudspeaker on its top to allow the plinth to be fitted. Align the screw holes and fit four M6 pozi head screws. A Carefully remove the loudspeaker from the carton and place on its top to allow access to the base of the cabinet. 1 3 Carefully unpack the plinth and place on the base of the cabinet.
D 3. Fit the desired feet, spikes for carpets or rubber feet where flooring is to be protected. If using Spikes – Insert the spikes and loosely fit lock nuts. Once upright, ensure the loudspeaker is stable. Adjust spikes where necessary to ensure loudspeaker is level, and then fully tighten lock nuts. Spike support cups are available to use where Spikes are preferred but flooring is to be protected.
Loudspeaker placement Left and Right loudspeakers can be identified by looking at the amplifier panel on the rear of each cabinet. Place the loudspeakers in your preferred position but within reach of wall sockets. With the wall socket in the OFF position connect the power lead to the loudspeaker using only the supplied power cables. Once connected, the mains switch can be turned to the ON position.
Wireless Connection Methods To use your speakers with a PC or MAC MAC set-up PC set-up 1.Insert the USB connector from the transmitter to a free USB socket on your MAC. 2.Go to System Preferences and under Hardware choose Sound. 3.Click Output in Menu and choose USB headset. 1.Insert the USB connector from the transmitter to a free USB socket on your PC or laptop. 2.Wait until the software has been installed, usually a confirmation beep or message window alert.
To use your speakers with MP3 devices (headphone out) Plug one end of the supplied 3.5mm mini jack lead into the transmitter and the other end into the headphone socket on your device. Plug the USB connector from the transmitter into the mains adapter and plug the mains adapter into a convenient wall socket and turn on. Push the button in the centre of the transmitter to select a free zone. Using the remote control press the “station” button” to find the signal from the new source equipment.
Transmitter Receiver 1 2 1 2 1 2 1 2 R L 11
Remote Control MUTE POWER ON/OFF STATION VOL+ BACK FWD VOLPLAY / PAUSE 12
Rear Panel 3 1 POWER 1 2 3 2 STATION 13 3 ZONE 1 2
Wireless Status Before turning on your WS90t loudspeakers, locate the ZONE setting switch on the rear of each loudspeaker and set to A The system has three channels: Blue (default) Red and Green. The loudspeakers and Transmitter are connected wirelessly when they are both operating on the same channel, Blue, Red or Green.
Multi-Zone More WS90t loudspeakers can be added to the network and up to three Zones can be set allowing independent control of Volume level and Channel selection. The Zone selector switch is on the rear of the loudspeaker. Select A, B or C to set a pair of speakers to a particular Zone. Example 1 Front room 1 pair Zone A Bedroom 1 pair Zone B Music room 1 pair Zone C Each zone can now be independently controlled using the same remote control.
Track Selection This function can only be used when the Transmitter is connected to PC/Mac/Laptop using USB When the transmitter is connected to a PC/Mac/Laptop by USB, the following commands can be sent to the installed media player (Windows and Mac operating systems) using the remote control.
Important Safety Instructions The loudspeaker is covered with a soft faux leather material. Please take care when unpacking the loudspeaker to avoid scratching or indenting the material. This symbol indicates that there are important operating and maintenance instructions in the literature accompanying this unit. This symbol indicates that dangerous voltage constituting a risk of electric shock is present within this unit. This equipment is a Class II or double insulated electrical appliance.
01. Read these instructions. 02. Keep these instructions. 03. Heed all warnings. 04. Follow all instructions. 05. Do not use apparatus near water. 06. Clean only with a dry cloth. 07. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 08. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 09.
C. If the apparatus has been exposed to rain or water, D. If the apparatus does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the apparatus to its normal operation. E. If the apparatus has been dropped or damaged in any way, and. F.
FCC Compliance This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
FCC RF Exposure Requirements (MPE) To satisfy FCC RF exposure requirements, a separation distance of 20 cm or more should be maintained between the antenna of this device and persons during device operation. To ensure compliance, operations at closer than this distance is not recommended. Les antennes installées doivent être situées de facon à ce que la population ne puisse y être exposée à une distance de moin de 20 cm.
Blue Aura Worldwide Guarantee This entitles you to have the unit repaired free of charge, during the first two years after purchase, at any authorised Blue Aura distributor provided that it was originally purchased from an authorised Blue Aura dealer or distributor.
Amplifier High Frequency Unit 1” Soft Dome Low Frequency Unit 4.
