TotalBlender™ Designer Series Owner’s Manual and User Guide
Table of Contents SECTION 1 - IMPORTANT SAFEGUARDS � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 5 SECTION 2 - UNPACKING � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 7 2.1 UNPACKING YOUR BLENDER 2.2 RECORDING YOUR SERIAL NUMBER AND DATE OF PURCHASE SECTION 3 - BLENDER OVERVIEW � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 7 3.1 BLENDER MOTOR 3.
SECTION 1 – IMPORTANT SAFEGUARDS IMPORTANT INFORMATION Following these instructions will help prevent injuries and damage to the machine and will ensure that you have the best possible experience with your Blendtec blender. 1.1 AVOID CONTACT WITH MOVING PARTS • ALWAYS keep fingers, hands, hair and clothing away from all moving parts. • ALWAYS keep all utensils away from the drive socket and blender jar blades during operation. Metal utensils may damage blade and jar.
1.8 JAR MUST BE PROPERLY IN PLACE WHILE APPLIANCE IS OPERATING 1.9 CARE SHOULD BE TAKEN WHEN HANDLING THE CUTTING BLADES, WHILE EMPTYING THE JAR, AND DURING CLEANING 1.10 USE CAUTION WHEN BLENDING ON THE SOUP CYCLE When blending on the soup cycle, friction of the blade will heat the contents. The vented lid will allow pressure relief. Be careful not to come in contact with any steam coming from the clear center lid. 1.11 WARNING - DO NOT BLEND HOT LIQUIDS OR OTHER HOT INGREDIENTS 1.
3.2 BLENDER MOTOR BASE FIGURE 1: BLENDER JAR ASSEMBLY • Blender Drive Socket: This is where the jar couples with the motor to turn the blade assembly. • LED Information Center: Indicates the number of times a blend cycle button has been pressed, the time left to blend, and error messages. Clear Vented Cap Insert Lid • Touch Area: Consists of six buttons that contain pre-programmed settings for selective blender control, a pulse button, a power button, a stop button, and a manual speed control slider.
FIGURE 3: TOUCH AREA 5.3 ALL ABOUT BLEND CYCLES (SEE FIGURE 4) 1. WHY BLEND CYCLES? In the world of professional blending, there are many factors which go into making a delicious blended product time after time. In order to blend many different recipes consistently well, Blendtec developed blend cycles to match the blending needs of the product being made. Because different ingredients have different blending characteristics, each item needs to be considered.
FIGURE 4 Ice Cream SPEED SPEED Batters (23 seconds) 14s 3s 4s 27s 3s 15s 2s TIME (in seconds) TIME (in seconds) Whole Juice (50 seconds) SPEED SPEED Ice Crush (35 seconds) 15s 10s 10s 10s TIME (in seconds) 3s TIME (in seconds) 12 20s 16s Soups SPEED SPEED 24s 3s 2s 2s TIME (in seconds) Smoothie (40 seconds) 10s (45 seconds) (90 seconds) 85s 3s 2s TIME (in seconds) 13
SECTION 6 - CARE AND CLEANING 6.1 AFTER USE CLEANING 1. Add 1 cup (240 ml) of hot water and a drop of liquid dishwashing soap to the blender jar. 2. Place the lid tightly onto the jar. Place the blender jar on the blender base and, with your hand placed on top of the lid, press the pulse button for 5 seconds. 3. Rinse with clear water until all soap is rinsed from jar and lid. 4. Clean the blender base by simply wiping the base and touchpad with a damp cloth. 6.2 LONG-TERM SANITATION 1.
INSTRUCTIONS THAT APPEAR IN THIS USER GUIDE ARE NOT MEANT TO COVER EVERY POSSIBLE CONDITION OR SITUATION THAT MAY OCCUR. GOOD JUDGMENT MUST BE USED WHEN OPERATING THIS OR ANY OTHER MACHINERY. 2. If the difficulty cannot be resolved over the phone, your unit may require replacement. If blender is under warranty, Blendtec will repair or replace the unit at no cost. Cosmetic damage and abuse are not included. SECTION 8 - WARRANTY U.S. AND CANADA 3.
Products intended for sale in the United States and Canada are only covered by U.S. and Canadian warranty, repair policies, and procedures. Products used or sold outside the United States and Canada are subject to the applicable international warranty and service procedures. Using a machine outside the country it was designed for will void the warranty.
1206 South 1680 West Orem, Utah 84058 U�S�A� 1-801-222-0888 blendtec�com ©2011 K-TEC, INC�, All Rights Reserved� Blendtec is a registered trademark of K-TEC, INC� OWN-RE-074 Manual, Owner’s, Total Blender Designer Series Rev 01