Owner's Manual

ManualsBrandsBLAZER INTERNATIONAL ManualsCell PhonesWIRELESS MANAGEMENT SYSTEM FOR SMARTPHONES

CWL623 • BLAZER LINK™ • OWNER

’

S MANUAL

BLAZER-INTERNATIONAL.COM

1-800-835-0129

Patent Pending

Page 1 of 10

FCC ID: TJJCWL623HCO

IC: 6047A-CWL623HCO

Model Name:CWL623HCO

Overview

This is a professional wire management system that is linked to your smartphone. The Blazer Link™

is designed for operating accessories (including lights, horns, warning beacons, etc.) typically used on

work or off-road vehicles (trucks, jeeps, ATV/UTV, boats, heavy equipment, farm equipment, etc.).

The unit works on 12V DC and provides output to four terminals which are protected by a 40A fuse.

Please note that before you can operate this system, you need to download and install the Blazer

Link™ App on your smartphone from the App store.

Main Unit

Please read these instructions carefully before installing this product. It is recommended to

consult a professional installer to prevent damage to vehicle and/or system.

Do not connect to 24V DC or higher voltage system, as this product is designed for a 12V DC

battery system. In case you have a larger than 12V DC system, check vehicle owner’s manual to

determine if a 12V DC output is available and how to connect in order to use it safely, otherwise,

the product will be damaged.

Find a suitable flat surface near the battery, clean the surface free of dirt and oil and then affix the

unit using provided adhesive strips and/or mounting holes.

Remove the 40A fuse from the holder and disconnect the vehicle battery.

Securely attach the positive (red) cable of the Blazer Link™ unit to the positive terminal of the

battery or battery cable and the negative (black) cable of the Blazer Link™ to the negative battery

cable or chassis.

Terminal 2A has additional light control functions like adjusting brightness and strobe rate, and

should not be used for connecting warning/strobe lights or horns.

Attach the auxiliary lights/equipment following correct polarity on the terminals and not exceeding

the maximum amperage of the channels (amperage printed on Blazer Link™ and corresponds to

amperage on your smartphone App for each terminal). See FIG 1 (on page 3)

Reconnect battery cables.

Insert the 40A fuse back into the holder and snap the cover close.

App Instructions

Download and install the Blazer Link™ App for your smartphone operating system available on

App Stores.

For initial setup, tap the “radio” icon to go to the “connect” screen. Simply select the module

and enter the appropriate numerical password (default is 123456).

Once connected, hit the back button on top right hand screen, to return to the main screen.

Now, select your vehicle type by tapping on the arrow to the right of the initial schematic.

Next, select light location setup to assign lights to different locations on your vehicle. Tap on

the terminal and then tap on the desired location. Repeat this for the remaining terminals and

then hit enter to return to the main screen.

You are now set up to operate your lights.

Activate the system by tapping the power icon . It will turn green to indicate that it is

powered on .

Now, select a light. The light icon will turn blue to indicate it is the active selection.

Summary of content (6 pages)

PAGE 1
CWL623 • BLAZER LINK™ • OWNER’S MANUAL BLAZER-INTERNATIONAL.COM 1-800-835-0129 FCC ID: TJJCWL623HCO IC: 6047A-CWL623HCO Model Name:CWL623HCO Overview This is a professional wire management system that is linked to your smartphone. The Blazer Link™ is designed for operating accessories (including lights, horns, warning beacons, etc.) typically used on work or off-road vehicles (trucks, jeeps, ATV/UTV, boats, heavy equipment, farm equipment, etc.).
PAGE 2
CWL623 • BLAZER LINK™• OWNER'S MANUAL BLAZER-INTERNATIONAL.COM 1-800-835-0129 9. You can turn on and off the light via the “individual Terminal ON/OFF” switch. Note: Terminals marked are used in conjunction with a warning light with different strobe patterns built into it. Most warning lights with strobe function come with three wires, black, red and yellow. Black is to be connected to negative terminal, red to positive terminal and yellow is for advancing the strobe patterns.
PAGE 3
CWL623 • BLAZER LINK™ • OWNER’S MANUAL BLAZER-INTERNATIONAL.COM 1-800-835-0129 Specifications (continued) FIG 1 FIG 1 2 5 1 4 6 1 Main Unit 2 Terminals 3 Eyelet for Mounting Installation 4 Fuse Holder 5 Negative Cable 6 Positive Cable 3 Troubleshooting Symptom Possible Cause and Solution Auxiliary lights/equipment not operational. 1. 2. 3. 4. 5. 6. 7. Wires not connected properly in the terminals. If the contacts don’t open, gently push downwards on the screws.
PAGE 4
FCC Statement THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS FOR A CLASS B DIGITAL DEVICE, PURSUANT TO PART 15 OF THE FCC RULES. THESE LIMITS ARE DESIGNED TO PROVIDE REASONABLE PROTECTION AGAINST HARMFUL INTERFERENCE IN A RESIDENTIAL INSTALLATION. THIS EQUIPMENT GENERATES, USES, AND CAN RADIATE RADIO FREQUENCY ENERGY, AND IF NOT INSTALLED AND USED IN ACCORDANCE WITH THE INSTRUCTIONS, MAY CAUSE HARMFUL INTERFERENCE TO RADIO COMMUNICATIONS.
PAGE 5
CWL623 • BLAZER LINK™ • OWNER’S MANUAL BLAZER-INTERNATIONAL.COM 1-800-835-0129 Blazer Link App Hopkins Manufacturing Corporation 428 Peyton St., Emporia, KS 66801 www.HopkinsMfg.com | 1-620-342-7320 www.FloTool.
PAGE 6
FCC Warning This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.