user manual Model #:BLZ-36-VHOOD
ii | Table of Contents Table of Contents 1 Safety Notice 2 Diagrams III-V 1-3 Hood Dimensions 3 . . . . . . . . . . . 1 Control Panel . . . . . . . . . . . . . . 2 Clearance . . . . . . . . . . . . . . 3 . Installation 4-10 Instructions 4 . . . . . . . . . . . . . . 4-6 Venting Options . . . . . . . . . . . . . 7 Hood Installation . . . . . . . . . . . . 8-9 Motor Rotation Instructions . . . . . . . . .
IMPORTANT SAFETY NOTICE upon receipt of your hood: 1) Inspect your hood for any damage in shipping 2) Plug in and test controls (lights, fan) before installing. 3) Call your dealer immediately to report any damage Please note: You must report any damage directly to your dealer immediately upon receipt to address any issues.
iv | Safety Notices 1 IMPORTANT SAFETY NOTICE Installer: Leave this guide with the homeowner. Consumer: Keep this guide for future reference. The Important Safety Notice and warnings in this manual are not meant to cover all possible problems and situations that can occur. Use common sense and caution when installing, maintaining or operating this or any other appliance. Always contact your dealer with any problems or situations that you do not understand.
Safety Notices 1 IMPORTANT SAFETY NOTICE Warning ♦ If you receive a damaged product, immediately contact your dealer. Do not install or use a damaged hood. ♦ Do not install, repair or replace any part of the range hood unless specifically recommend-ed in the literature accompanying it. ♦ Use the range hood only for its intended purpose as outlined in this manual. DO NOT use this range hood to vent hazardous or explosive materials or vapors. ♦ Do not tamper with the controls.
1 | BLAZE OUTDOOR clearance dimensions
USER MANUAL Control Panel A MAIN SWITCH A) A B B C FAN: To adjust the speed of motor, each motor has 4 speed settings. Turning the knob once clockwise will start the motor in the lowest speed setting. Continuing to turn the knob clockwise will allow the motor to advance to the highest setting. Turning counter clockwise will return the motor to the original position and stop the motor. B) LIGHTS: To turn on lights, turning the knob once clockwise will turn on the lights.
3 | BLAZE OUTDOOR clearance dimensions
USER MANUAL instructions warning It is important to install the hood at the proper mounting height. Hoods mounted too low could result in heat damage and fire hazard. Hoods mounted too high will be hard to reach and will lose performance and efficiency. For best installation, we recommend you: ♦ Plug in and test controls (lights, fan) before installing.
5 5 | BLAZE OUTDOOR instructions Tools Needed Utility Knife Measuring Tape Marker or Pencil Level Powered Drill Flat & Phillips Screwdrivers
USER MANUAL instructions Parts Supplied Range Hood Grease Trays: 2 PCS Duct Connector 1 PCS #2 Amounting Screws Qty: 4 PCS #5 Qty: 10 PCS #3 Wall Anchors Qty: 2 PCS Stainless Steel Baffle Filters: 6 PCS #4 Amounting Screws Qty: 7 PCS Mounting Bracket: 2 PCS #1 Qty: 8 PCS | 6
5 7 | BLAZE OUTDOOR venting options Wall venting Option 1 vertical roof venting A -18” from the side edge of the hood to the center of the duct B - 5 11/16" from the wall to the center of the duct (using the included mounting bracket which is between the wall and hood and is roughly an 1/8” thick) *Note: the included transition pieces come ready to accept 8" ducting
USER MANUAL | 8 wall hood installation PREPARATION Plan where the ductwork will be located. Install proper-sized ductwork, and roof or wall cap, depending on where you will be venting your hood. Adjust your measurements to accommodate heights of ceilings, cabinets, or range-tops. Remember to plug in and test the hood prior to installation. When planning for the installation of the vent h o o d please include an opportunity to access the top of the hood when the installation is complete.
9 | BLAZE OUTDOOR wall hood installation STEP 2 Install the two grease trays in the front and back of the unit. When installed, these trays. will accept the grease filters on the bottom side. When installing the drip trays, place each tray in the recession at the front and rear as show in the drawing. Be sure to have the small front bend hook over the lip of the recession. STEP 3 Install all grease filter handles to the filters using the included screws.
USER MANUAL | 10 MOTOR ROTATION INSTRUCTIONS Getting Started The image to the right shows the position of the motors directly from the factory. This position of the motor is used when running vertical pipe for your venting. STEP 1 REMOVE COVER PLATE There are two sets of screws you will be working with on the cover plate. The smaller screws closest to the edges of the plate hold the plate to the hood itself. The larger screws closer to the center hold the motor to the cover plate.
1 1 | BLAZE OUTDOOR Care & Cleaning warning ♦ Never put your hand into the area housing the fan while the fan is operating. ♦ Turn off and disconnect power to the hood before cleaning. ♦ Make sure your cook-top and hood are cool before cleaning. ♦ Use only the types of cleaning solutions mentioned in this manual. ♦ Completely dry the filter(s) immediately after cleaning. cleaning exterior surfaces ♦ Regular care will help preserve the appearance of your range hood .
USER MANUAL Care & Cleaning step 2 step 1 Slide filter forward off of rear lip. Lower filter rear, then slide filter front out. Repeat this step for all filters on the front and back of the hood. When cleaning filters, always remove the grease channels and clean with hot soapy water. Both the filters and the channels are dishwasher safe. Dry throughly before re-installing.
13 | BLAZE OUTDOOR troubleshooting NOTHING WORKS (Control Panel not responding, Blower not working) Solution 1: Turn on power at circuit breaker panel or fuse box . Check for tripped breaker or blown fuse under the black plastic cover on the rear of the hood. Solution 2: Make sure hood power cable is plugged in and powered. LIGHTS NOT TURNING ON Solution 1: see “nothing works” Solution 2: Check the wiring on the lights to insure a secure connection/ no. loose wires.
USER MANUAL Warranty One Year Warranty - Parts Only For one year from the date of original purchase, we will repair or replace any non-consumable parts or components that failed due to manufacturing defects. ATTENTION International Customers: Please consult your selling dealer or distributor for specifics pertaining to your product warranty and procedure. No one else is authorized to perform any obligations under this warranty.