General Safety Rules 1 Specific Safety Rules 2 Symbols 3 Additional Safety Rules 4 General Information 5 Functional Description 6 Operation 7 Maintenance 8 Polishing/Sanding MODEL BL-183 / BL-233 Sander/ Polisher
BL-183 / BL-233 SANDER/POLISHER SECTION 1 GENERAL SAFETY RULES INSTRUCTION MANUAL OCTOBER 2008 CONTENTS – SECTION 1 GENERAL SAFETY RULES WARNING – To reduce the risk of injury, user must read instruction manual. General Safety Rules WARNING! Read all instructions Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury.
BL-183 / BL-233 SANDER/POLISHER SECTION 1 GENERAL SAFETY RULES INSTRUCTION MANUAL OCTOBER 2008 d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. f) Dress properly. Do not wear loose clothing or jewellery.
BL-183 / BL-233 SANDER/POLISHER SECTION 2 SPECIFICSAFETY RULES INSTRUCTION MANUAL OCTOBER 2008 CONTENTS – SECTION 2 SPECIFIC SAFETY RULES Safety Warnings Common for Sanding or Polishing Operations: a) This power tool is intended to function as a sander or polisher tool. Read all safety warnings, instructions, illustrations and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury.
BL-183 / BL-233 SANDER/POLISHER SECTION 2 SPECIFICSAFETY RULES INSTRUCTION MANUAL OCTOBER 2008 k) Position the cord clear of the spinning accessory. If you lose control, the cord may be cut or snagged and your hand or arm may be pulled into the spinning accessory. l) Never lay the power tool down until the accessory has come to a complete stop. The spinning accessory may grab the surface and pull the power tool out of your control. m) Do not run the power tool while carrying it at your side.
BL-183 / BL-233 SANDER/POLISHER SECTION 2 SPECIFICSAFETY RULES INSTRUCTION MANUAL OCTOBER 2008 Safety Warnings Specific for Polishing Operations: a) Do not allow any loose portion of the polishing bonnet or its attachment strings to spin freely. Tuck away or trim any loose attachment strings. Loose and spinning attachment strings can entangle your fingers or snag on the workpiece.
BL-183 / BL-233 SANDER/POLISHER INSTRUCTION MANUAL OCTOBER 2008 SECTION 3 SYMBOLS CONTENTS – SECTION 3 SYMBOLS The following denominations and symbols are used in the Operating Instructions to highlight areas of particular importance: Symbol of operational safety. In these Operating Instructions this symbol will be shown next to all safety precautions that are to be taken in order to ensure prevention of life and injury. Follow these instructions and take special care in these circumstances.
BL-183 / BL-233 SANDER/POLISHER INSTRUCTION MANUAL OCTOBER 2008 SECTION 3 SYMBOLS Indications where consultation with the manufacturer is required. Instructions relating to periodic checks. Reference to important instructions contained in the Operating Instructions.
BL-183 / BL-233 SANDER/POLISHER SECTION 4 ADDITIONAL SAFETY RULES INSTRUCTION MANUAL OCTOBER 2008 CONTENTS – SECTION 4 ADDITIONAL SAFETY RULES The Operating Instructions are to be kept near the location where the machine is being operated, and must be within reach at all times! Grounded tools must be plugged into an outlet properly installed and grounded in accordance with all codes and ordinances. Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded.
BL-183 / BL-233 SANDER/POLISHER SECTION 4 ADDITIONAL SAFETY RULES INSTRUCTION MANUAL OCTOBER 2008 The Operating Instructions must be supplemented by other instructions; this includes the duty to supervise and report incidents relating to particular working practices, for example, work organization, work procedures and personnel allocation. Personnel entrusted with working with the machine must read the Operating Instructions before starting work, in particular all safety instructions.
BL-183 / BL-233 SANDER/POLISHER SECTION 4 ADDITIONAL SAFETY RULES INSTRUCTION MANUAL OCTOBER 2008 Intervals for recurring checks and inspections specified in these Operating Instructions must be complied with! To perform maintenance work correctly, it is imperative to be equipped with the proper tools for the task in question.
BL-183 / BL-233 SANDER/POLISHER SECTION 4 ADDITIONAL SAFETY RULES INSTRUCTION MANUAL OCTOBER 2008 Check the machine visually for any damage and defects at least once a day! In the event of operational malfunctions, the machine must be shut down immediately and secured, and the fault must be rectified! Carry out the switch on and switch off operations in accordance with the operations manual! Do not switch off, or remove the exhaust, and/or the ventilation devices while the machine is running! All person
BL-183 / BL-233 SANDER/POLISHER SECTION 4 ADDITIONAL SAFETY RULES INSTRUCTION MANUAL OCTOBER 2008 c) When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance section of this manual. Use of unauthorized parts or failure to follow Maintenance instructions may create a risk of electric shock or injury.
BL-183 / BL-233 SANDER/POLISHER SECTION 4 ADDITIONAL SAFETY RULES INSTRUCTION MANUAL OCTOBER 2008 Electrical servicing work: Make sure that electrical components used for replacement purposes comply with the original parts and are correctly adjusted if necessary. Definition of the Safety Off Position: The machine is in a safe condition where it cannot generate any hazard. Putting the equipment in the Safety off position involves: 9 Switching off the grinding machine.
BL-183 / BL-233 SANDER/POLISHER SECTION 5 GENERAL INFORMATION INSTRUCTION MANUAL OCTOBER 2008 CONTENTS – SECTION 5 GENERAL INFORMATION 5.1 Range of application 5.
BL-183 / BL-233 SANDER/POLISHER INSTRUCTION MANUAL OCTOBER 2008 SECTION 5 GENERAL INFORMATION 5.1 RATING Unit / Designation: Sander / Polisher Machine Type: BL-183 / BL-233 Manufacturer: Blastrac US 13201 North Santa Fe Oklahoma City, OK 73114 United States of America Local: 405-478-3440 Toll-free: 800-256-3440 info@blastrac.com www.blastrac.com 5.
BL-183 / BL-233 SANDER/POLISHER SECTION 6 FUNCTIONAL DESCRIPTION INSTRUCTION MANUAL OCTOBER 2008 CONTENTS – SECTION 6 FUNCTIONAL DESCRIPTION 6.1 Range of application 6.
BL-183 / BL-233 SANDER/POLISHER SECTION 6 FUNCTIONAL DESCRIPTION 6.1 RANGE OF APPLICATION Use the BL-183 / BL-233 for the following applications only: • Sanding and grinding concrete surfaces • For removing rust from steel surfaces as well as finishing • Surface finishing wood • Polishing painted metal, lacquered wood, synthetic resin, etc.
BL-183 / BL-233 SANDER/POLISHER INSTRUCTION MANUAL OCTOBER 2008 SECTION 6 FUNCTIONAL DESCRIPTION 6.2 DESCRIPTION OF THE MACHINE 5 1 3 4 2 6 Item No. 1 2 3 4 5 6 Part Description Aux.
BL-183 / BL-233 SANDER/POLISHER SECTION 7 OPERATION CONTENTS – SECTION 7 OPERATION 7.
BL-183 / BL-233 SANDER/POLISHER INSTRUCTION MANUAL OCTOBER 2008 SECTION 7 OPERATION 7.1 OPERATING INSTRUCTIONS Before start-up, the operating personnel must be familiar with the safety regulations given in this manual. 4 2 6 This tool is started by depressing the safety (6) and engaging the switch (2). The tool is stopped by releasing the switch (2). For continuous operation, depress the lock button (4) while the switch is engaged. To release continuous operation, depress the switch (2) and release.
BL-183 / BL-233 SANDER/POLISHER SECTION 7 OPERATION INSTRUCTION MANUAL OCTOBER 2008 The handle can be attached to either side or on top. Make sure it is tight before use. Never cover the air vents since they must always be open for proper motor cooling. The key to efficient operating is controlling the pressure and surface contact between the disc/polishing wool and work piece.
BL-183 / BL-233 SANDER/POLISHER SECTION 8 MAINTENANCE CONTENTS – SECTION 8 MAINTENANCE 8.1 Care and Maintenance 8.
BL-183 / BL-233 SANDER/POLISHER SECTION 8 MAINTENANCE INSTRUCTION MANUAL OCTOBER 2008 8.1 CARE AND MAINTENANCE Operational safety and service life of the machine depend, among other things, on proper maintenance. After use, check the tool to make sure that it is in top condition. It is recommended that you take this to a Blastrac Authorized Service Center for a thorough cleaning and lubrication at least once a year. Do not make any adjustments while the motor is in motion.
BL-183 / BL-233 SANDER/POLISHER INSTRUCTION MANUAL OCTOBER 2008 SECTION 8 MAINTENANCE 8.