® Instruction Manual Bedienungsanleitung Manuel d’utilisation Manuale di Istruzioni ®
NOTICE All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC. For up-to-date product literature, visit horizonhobby.com and click on the support tab for this product.
® Box Contents: • • • • • Blade 330X 3S 11.1V 2200mAh 30C Li-Po Battery (RTF Only) DC Li-Po Balancing Charger (RTF Only) Spektrum DXe Transmitter (RTF Only) 4 AA Batteries (RTF Only) Table of Contents Pre-Flight Checklist ..............................................................................................9 Pre-Flight Checklist ............................................................................................10 Flying the Blade 330X Helicopter ..........................................
First Flight Preparation Flying Checklist • • • • • • • ❏ ❏ ❏ ❏ ❏ ❏ ❏ Remove and inspect contents Begin charging the flight battery Install the flight battery in the helicopter (once it has been fully charged) Program your computer transmitter Bind your transmitter (BNF only) Familiarize yourself with the controls Find a suitable area for flying Always turn the transmitter on first Plug the flight battery into the lead from the ESC Allow the ESC to initialize and arm properly Fly the model Land the model Un
Installing the DXe Transmitter Batteries (RTF) The LED indicator flashes and the transmitter beeps progressively faster as the battery voltage drops. Replace the transmitter batteries when the transmitter begins to beep.
DX7s, DX8 SYSTEM SETUP FUNCTION LIST Model Type Swash Type HELI 1 servo 90 F-Mode Setup Flight Mode Hold F Mode Hold SW Select Trainer F Mode Gyro Mix Hold Knob Aux 2 Gear INH INH INH INH Frame Rate 11ms DSMX Servo Setup Chan Travel THR 100/100 AIL 100/100 ELE 100/100 RUD 100/100 Reverse Normal Normal Normal Normal D/R & Expo Chan Switch Pos (Ail D/R) 0 AILE 1 2 0 ELEV 1 2 0 RUDD 1 2 Chan GER PIT AX2 D/R 100/100 85/85 85/85 100/100 85/85 85/85 100/100 85/85 85/85 Throttle Hold Throttle Expo 0
Installing the Flight Battery 1. 2. 3. 4. Lower the throttle. Power on the transmitter. Center the throttle trim. To allow the ESC to arm and to keep rotors from initiating at startup, turn on throttle hold and normal flight mode before connecting the flight battery. 5. Attach hook material to the helicopter frame and loop material to the battery. 6. Install the flight battery on the helicopter frame. Secure the flight battery with a hook and loop strap. Connect the battery cable to the ESC. 7.
Control Tests CAUTION: You must complete the Tail Rotor and Cyclic tests prior to every flight. Failure to complete the tests and ensuring the sensor corrects in the proper direction can cause the helicopter to crash, resulting in property damage and injury. 4. Move the rudder stick to the right. The pitch slider on the tail shaft should move toward the tail case. If the pitch slider moves in the opposite direction, ensure the rudder channel reverse setting within the transmitter is set to normal. 5.
Understanding the Primary Flight Controls If you are not familiar with the controls of your 330X, take a few minutes to familiarize yourself with them before attempting your first flight.
Pre-Flight Checklist ❏ Check all wire connections ❏ Check gears and make sure no teeth are missing ❏ Do a complete control test ❏ Verify the receiver sensor is correcting in the proper directions ❏ Check that servos are functioning properly ❏ Check to make sure the flight battery is properly secured ❏ Check to make sure receiver is properly secured ❏ Check all screws and ensure that they are tight ❏ Check belt tension and ensure that it is not too tight or too loose ❏ Check main and tail blades to ensure th
Post-Flight Inspections and Maintenance Ball Links Make sure the plastic ball link holds the control ball, but is not tight (binding) on the ball. When a link is too loose on the ball, it can separate from the ball during flight and cause a crash. Replace worn ball links before they fail. Cleaning Make sure the battery is not connected before cleaning. Remove dust and debris with a soft brush or a dry lint free cloth. Bearings Replace bearings when they become damaged.
DX7s / DX7 G2 / DX8 / DX8 G2 / DX9 / DX18 / DX20 Users: 1. Lower the throttle stick to the lowest position. Entering Gain Adjustment Mode DX6G2, DX6e and DX6i Users: 1. Lower the throttle stick to the lowest position. 2. Power ON the transmitter. 2. Power ON the transmitter. 3. Install the flight battery on the helicopter frame, securing it with the hook and loop strap. 3. Install the flight battery on the helicopter frame, securing it with the hook and loop strap. 4.
Servo Adjustment Your Blade 330 X was setup at the factory and test flown. The servo adjustment steps are usually only necessary in special circumstances, such as after a crash or if a servo or linkage is replaced. WARNING: To ensure your safety, always disconnect the motor wires from the ESC before performing the following steps. After you have completed the adjustments, reconnect the motor wires to the ESC before attempting to fly the model. 7.
Troubleshooting Guide Problem Helicopter will not bind to the transmitter (during binding) Helicopter will not link to the transmitter (after binding) AR636A will not initialize Helicopter will not respond to the throttle but responds to other controls Helicopter power is lacking Helicopter will not lift off The helicopter tail spins out of control The helicopter wobbles in flight Possible Cause Low flight battery or transmitter battery voltage receiver is not in bind mode Transmitter is not in bind m
Inspection or Services If this Product needs to be inspected or serviced and is compliant in the country you live and use the Product in, please use the Horizon Online Service Request submission process found on our website or call Horizon to obtain a Return Merchandise Authorization (RMA) number. Pack the Product securely using a shipping carton. Please note that original boxes may be included, but are not designed to withstand the rigors of shipping without additional protection.
HINWEIS Alle Anweisungen, Garantien und anderen zugehörigen Dokumente können im eigenen Ermessen von Horizon Hobby, LLC jederzeit geändert werden. Die aktuelle Produktliteratur finden Sie auf horizonhobby.com unter der Registerkarte „Support“ für das betreffende Produkt.
58 58 18 58 18 59 57 23 18 58 56 58 57 23 57 59 55 55 18 20 52 53 52 10 52 60 45 51 12 51 52 26 20 11 60 25 25 9 14 8 46 21 13 20 48 11 22 16 28 13 54 27 12 50 14 15 22 20 32 11 9 25 25 12 20 26 11 49 6 47 10 Exploded View / Explosionszeichnung / Vue Éclatée / Vista Esplosa
59 32 15 32 5 63 64 65 33 43 24 44 24 42 1 32 15 32 29 40 41 39 34 36 40 19 35 36 66 2 70 5 37 34 63 15 32 64 67 33 5 32 63 15 32 33 17
Parts List / Ersatzteile / Pièces de Rechange / Pezzi di Ricambio # Part # Deutsch Blade 450/300x/300CFX: HauptzahnBLH1901 Helical Main Gear B450/300X/CFX rad schrägverz. 450/300x/300CFX: Ritzel 10 Z BLH1902 Helical Pinion 10T B450/300X/CFX Blade schrägverz. Spektrum Ersatzgetriebe TaumelsSPMSP1040 Gears, Metal Cyclic 12 g Servo cheibenservo dig. 12g MG Spektrum Ersatzgetriebe HeckrotorsSPMSP1041 Gears, Metal Tail 12 g Servo ervo dig. 9g MG Spektrum Taumelscheibenservo dig.
# Part # 42 BLH1653 Français Set de fixations moteur en aluminium : B450 3D/X, B400 crochet et boucle pour ruban Hook & Loop Battery Strap: B450 Akku-Klettverschlussband B450 3D/X, Sangles adhésif d’accu : B450 3D/X, B400 (non 3D/X, B400 (not shown) B400 (nicht gezeigt) représenté) Landing Gear Set: B450 3D/X Fahrwerk-Set: B450 3D/X Set de train d’atterrissage : B450 3D/X One-Way Bearing Shaft and Shim Set Einweglagerwelle und Unterlagss- Axe de roue libre et set de rondelles : Set: B450 3D/X, B400 cheibe
Optional Parts / Optionale Bauteile / Pièces Optionnelles / Pezzi Opzionali Part # English Deutsch Blade 450/300x/300CFX: Helical Pinion 11T B450/300X/CFX Ritzel 11 Z schrägverz. Blade 450/300x/300CFX: Helical Pinion 12T B450/300X/CFX Ritzel 12 Z schrägverz. Blade 450/300x/300CFX: Helical Pinion 13T B450/300X/CFX Ritzel 13 Z schrägverz. Blade 450/300x/300CFX: Helical Pinion 14T B450/300X/CFX Ritzel 14 Z schrägverz. Blade 450/300x/300CFX: Helical Pinion 15T B450/300X/CFX Ritzel 15 Z schrägverz.
Part # English Tail Rotor Blade Set, Yellow: B450 3D/X, BLH1671YE B400 Rotor Blade Set, Green: B450 3D/X, BLH1671GR Tail B400 BLH1699 450 Carrying Case Deutsch Heckrotorblatt-Set, gelb: B450 3D/X, B400 Heckrotorblatt-Set, grün: B450 3D/X, B400 450 Tragekoffer BLH4006 Optionales Glasfaser-Kabinendach: 330X Verrière en fibre de verre en option : 330X Optional Fiberglass Canopy: 330X 63 Français Set de pales d'anticouple, Jaune : B450 3D/X, B400 Set de pales d'anticouple, Vert : B450 3D/X, B400 Coffret d
©2017 Horizon Hobby, LLC. Blade, DSM, DSM2, DSMX, Celectra, ModelMatch, Spektrum AirWare and EC3 are trademarks or registered trademarks of Horizon Hobby, LLC. The Spektrum trademark is used with permission of Bachmann Industries, Inc. Futaba is a registered trademark of Futaba Denshi Kogyo Kabushiki Kaisha Corporation of Japan US 7,391,320. D774,933. Other patents pending.