Contents 2 SE3-RDR100 INSTALLATION GUIDE 3 3 6 Install the SE3-RDR100 Surface Mount the SE3-RDR100 Single Gang Box Mount the SE3-RDR100 9 Remove the SE3-RDR100 10 Specifications PRINTED NOVEMBER 24, 2009 I
Figures Figure 1-1 Figure 1-2 Figure 1-3 Figure 1-4 Figure 1-5 Figure 1-6 Figure 1-7 Figure 1-8 Figure 1-9 Figure 1-10 SE3-RDR100 Reader.................................................................................2 Mounting Drill Pattern.................................................................................3 Mounting Plate Installation - Mullion...........................................................4 Mounting Plate Installation - Surface Mount..............................................
SE 3 - RD R1 0 0 I NSTALLATION GUIDE DOCUMENT 1 29 1 REV 01 Blackboard Inc. SE3-RDR100 Tested To Comply With FCC Standards FOR HOME OR OFFICE USE This Class B digital apparatus complies with Canadian ICES-003 Cet appareill numérique de la classes B est conform à la norme NMB-003 du Canada This device complies with Part 15 of the FCC Rules.
S E3 -R D R 100 I N S TA L L A T IO N G U ID E The Blackboard SE3-RDR100 is a Door Access Reader that supports contactless card technology. Contactless Card Technology offers the following advantages vs. magnetic stripe: virtually eliminates reader wear and tear (card need not contact the reader) Figure 1-1 SE3-RDR100 Reader The SE3-RDR100 Card Reader may be mounted or a single gang box using the included backing plate.
SE 3 - RD R1 0 0 I NSTALLATION GUIDE D OCUMENT 1 29 1 REV 01 I NSTALL THE SE3-RDR100 UL Considerations: Attention to Installers: All field wiring/cabling connections made to the Controller need to use shielded cable with one of the shielded ends connected to earth ground. Surface Mount the SE3-RDR100 (page 1-3) Single Gang Box Mount the SE3-RDR100 (page 1-6) The mounting plate is secured using #6 flat head hardware. Select hardware based on the mounting material.
INSTALL THE SE 3 - RDR 1 0 0 3 Secure the mounting plate with the chosen hardware. Figure 1-3 Mounting Plate Installation - Mullion 4 Pull the cable through the hole, and then wire to the 5-pin terminal block. SE3-RDR100 Wiring 5 Plug the terminal block onto the SE3-RDR100. 6 Place SE3-RDR100 at an angle over the mounting plate, and then slide down to engage the clip onto the mounting plate notch.
SE 3 - RD R1 0 0 I NSTALLATION GUIDE D OCUMENT 1 29 1 REV 01 Figure 1-4 Mounting Plate Installation - Surface Mount 7 Push the bottom of the reader onto the mounting plate to lock the unit to the plate. Figure 1-5 Mullion Installation 8 Test the SE3-RDR100 for proper operation. 9 Optionally secure the reader to the mounting plate using the security screw supplied in the hardware kit. 10 Apply the Security Screw Cover Decal.
INSTALL THE SE 3 - RDR 1 0 0 To mount the SE3-RDR100 onto a single gang box 1 Secure the backing and mounting plates with the appropriate hardware to the single gang box. Figure 1-6 Single Gang Box Mount Assembly 2 Pull cable through mounting plate, and then connect to 5-pin terminal block, see: SE3-RDR100 Wiring (page 1-8). 3 Plug the terminal block onto the SE3-RDR100. 4 Place SE3-RDR100 at an angle over the mounting plate, and then slide down to engage the clip onto the mounting plate notch.
SE 3 - RD R1 0 0 I NSTALLATION GUIDE D OCUMENT 1 29 1 REV 01 Figure 1-7 Mounting Plate Installation - Gang Box Mount 5 Push the bottom of the SE3-RDR100 onto the mounting plate to lock the unit to the plate. Figure 1-8 Single Gang Box Mount 6 Test the reader for proper operation. 7 Optionally secure the reader to the mounting plate using the security screw supplied in the hardware kit. 8 Apply the Security Screw Cover Decal.
INSTALL THE SE 3 - RDR 1 0 0 Jumper wire between PINS 1 & 5 Figure 1-9 SE3-RDR100 Wiring PRINTED NOVEMBER 24, 2009 1-8
REMOVE THE SE 3 - RDR 1 0 0 R EMOVE THE SE3-RDR100 To remove the SE3-RDR100 from its mounting 1 If a security screw is installed, remove the Security Screw Cover Decal. 2 Insert the SE3-RDR100 key into the bottom slots. 3 Gently pull the bottom of the reader at an angle over the mounting plate, and then slide up to disengage the clip from the mounting plate. 4 Disconnect the terminal block. 5 Remove the wall plate from the mounting if needed.
SPECIFICATIONS SPECIFICATIONS Physical Size: Weight: 0.30 lbs Input Power: 12VDC 150mA, 1.8 Watts Maximum Operating: Temperature: -20 to 60+ degrees Celsius Relative Humidity: 0 to 95 percent, non-condensing Altitude: 0 - 10,000 feet Non-Operating: Temperature: -20 to +70 degrees Celsius Relative Humidity: 0 to 95 percent, non-condensing Altitude: 0 - 35,000 feet This device contains an integrated lithium battery (BR2032). There is a risk of fire if the battery is replaced with an incorrect type.