LC3000 Laundry Center Installation and Setup Guide
The following information applies to wired LC3000 systems equipped with LCM20s only. Blackboard Inc. LC3000 Tested To Comply With FCC Standards FOR HOME OR OFFICE USE This Class A digital apparatus complies with Canadian ICES-003 The following information applies to wireless systems equipped with LWIs and LE3/BRIDGES only. Blackboard Inc. LWI30xx Tested To Comply With FCC Standards FOR HOME OR OFFICE USE This device complies with Part 15 of the FCC Rules.
CONTENTS 1 LC3000 Laundry Center Installation 3 Laundry Center Components 3 LC3000 Components 4 Laundry Center Installation Overview 5 LC3000 Laundry Reader Installation 6 7 Install the LC3000 Enclosure LC3000 Laundry Reader Configuration 8 8 8 Configure LC3000 Reader using front panel Configure LC3000 Reader using RS-232 Configure LC3000 Reader using Telnet 9 Wired Laundry Machine Interface Installation 10 Laundry Controller Multiplexer (LCM20) Installation 10 Install the LCM20 in the LC300
16 Wireless Laundry Machine Interface Installation 17 18 19 20 Wireless Bridge LE3/BRIDGE Installation Laundry Wireless Interface Module (LWI) Installation Install the LWI3010 Module for Maytag laundry machines Install the LWI3020 Module for Alliance/Speed Queen laundry machines 22 Appendix 22 Features 23 Transaction Process 24 Manager Menus 25 Laundry Components Dimensions and Weight 27 LC3000 Laundry Reader Default Configuration Settings 27 Restore Default Settings 28 MW9010/MW9012 Laundry
LC3000 LAUNDRY CENTER INSTALLATION LC3000 L A U N D R Y C E N T E R I N S TA L L A T I O N This manual provides instructions for selecting, installing, and configuring the Blackboard Laundry Center using the LC3000 Laundry Reader. The LC3000 Laundry Reader controls laundry machines across a laundry Center network and Blackboard Transaction System (BbTS) and communicates with users interface through a display, keypad, and mag-stripe reader.
LC3000 LAUNDRY CENTER INSTALLATION Wireless Solution Up to 60 laundry machines can be connected wirelessly to the LC3000 using a Wireless Bridge (LE3/BRIDGE). Each Bridge communicates with laundry machines within 60 feet. Multiple Wireless Bridges can be used if stone or metal obstructions reduce the range. Each laundry machine connects to a Laundry Wireless Interface installed inside the machine.
LAUNDRY CENTER COMPONENTS L AUNDRY CENTER C OMPONENTS LC3000 Components COMMON COMPONENT Laundry Reader LC3000 Each LC3000 supports up to 60 machines (stacked units count as 2 machines). Wired installations require LCM20(s) and LCIs. Wireless installations require LE3/BRIDGE(s) and LWI(s). WIRED COMPONENTS Each LCM20 supports 20 wired machines. The first LCM20 is installed inside the LC3000. The second and third LCM20s each require a Power Supply Enclosure (LE3/PSENCL).
LAUNDRY CENTER INSTALLATION OVERVIEW L AUNDRY CENTER I NSTALLATION OVERVIEW 1 Configure Laundry Machines in BbTS.
LC3000 LAUNDRY READER INSTALLATION LC3000 L A U N D R Y R E A D E R I N S TA L L A T I O N The LC3000 Laundry Reader must be mounted on a wall in a location that is convenient to cardholders and wiring requirements. LC3000 Mounting Location Considerations • 120 VAC power availability Connect to 120 VAC @ 60 Hz. Connect only to a 15A maximum branch circuit protection or equivalent. Use a circuit breaker or switch to disconnect power when installing or removing the LC3000.
LC3000 LAUNDRY READER INSTALLATION Install the LC3000 Enclosure 1 Inside the LC3000, remove the power supply cover to access the upper right mounting hole. Protect power supply from debris while mounting the enclosure. 2 Secure enclosure to a wall using hardware appropriate to wall material. Mounting holes accept up to 1/4'' hardware. Disconnect external AC power when installing wiring. 3 4 Strip back insulation on AC wire .28" to prevent bare wire exposure when installed in AC terminal block.
LC3000 LAUNDRY READER CONFIGURATION LC3000 LAUNDRY READER C ONFIGURATION The Laundry Reader must be configured to communicate with the BbTS network.
LC3000 LAUNDRY READER CONFIGURATION Configure LC3000 Reader using front panel 1 Swipe a Service Card, and then press NEXT on Reader to start configuration process. 2 Adjust each setup parameter using the keys displayed on the Terminal. • ACCEPT - Accept displayed value and advance to next setting. • CHANGE - Change displayed value. • ABORT - Abort configuration process.
WIRED LAUNDRY MACHINE INTERFACE INSTALLATION W I R E D L A U N D R Y M A C H I N E I N T E R F A C E I N S TA L L A T I O N The wired Blackboard laundry solution supports up to 60 laundry machines. Multiplexers (LCM20s) facilitate up to 20 wired machine connections each. In laundry centers with 20 or fewer machines, a single Multiplexer is installed inside the LC3000 enclosure.
LAUNDRY CONTROLLER MULTIPLEXER (LCM20) INSTALLATION L AUNDRY CONTROLLER MULTIPLEXER (LCM20) I NSTALLATION LCM20 Placement Considerations • 120 VAC power availability Connect to 120 VAC @ 60 Hz. Connect only to a 15A maximum branch circuit protection or equivalent. Use a circuit breaker or switch to disconnect power when installing or removing the LC3000.
LAUNDRY CONTROLLER MULTIPLEXER (LCM20) INSTALLATION Install External LCM20(s) (if required) If your Laundry Center has more than 20 machines, an external LCM20 and LE3/PSENCL are required. 1 Inside the LE3/PSENCL, remove the power supply cover to access the upper right mounting hole (Figure 12). Protect power supply from debris while mounting the enclosure. 2 Secure the enclosure to the wall using hardware for wall material. Mounting holes accept up to 1/4” hardware.
LAUNDRY CONTROLLER INTERFACE (LCI) INSTALLATION L AUNDRY CONTROLLER I NTERFACE (LCI) INSTALLATION The Laundry Controller Interface (LCI) is installed inside each laundry machine. The Laundry Controller Interface (LCI) is a wiring harness that connects to the laundry machine controller. The LCI is then connected to the Laundry Controller Multiplexer (LCM20) to communicate with Laundry Reader. The Laundry Controller Interface (LCI) model used depends on the laundry machine manufacturer.
LAUNDRY CONTROLLER INTERFACE (LCI) INSTALLATION 6 Use the wire ties and wire tie blocks included in the hardware kit to dress the wires, and replace the laundry machine operator console. 7 Terminate the 4-conductor cable at the LCM20 1 x 4 terminal block(s).
LAUNDRY CONTROLLER INTERFACE (LCI) INSTALLATION Install Alliance/Speed Queen LCI3020 in Laundry Machine Two LCI3020s must be ordered when wiring to a stacked dryer. Laundry Controller Multiplexer (LCM20) Speed Queen Laundry Machine 4-pin Molex white 4 black 3 red 2 black 1 white 1 2 black 3 white 4 red red black BELDEN 8723 or equivalent 4-conductor cable green green FIGURE 17: Alliance/Speed Queen Machine (LCI3020) 1 Remove the operator console from the machine.
LAUNDRY CONTROLLER INTERFACE (LCI) INSTALLATION Install Whirlpool LCI3030 in Laundry Machine Stacked dryers require two LCI3030s. Laundry Controller Multiplexer (LCM20) Whirlpool Advantech Laundry Machine 1 2 black 3 white 4 black M2 red red COIN 1 white green BELDEN 8723 or equivalent 4-conductor cable green FIGURE 18: Whirlpool/Advantech Single Machine (LCI3030) 1 Remove the operator console from the machine. Refer to Whirlpool service manual.
WIRELESS LAUNDRY MACHINE INTERFACE INSTALLATION W I R E L E S S L A U N D R Y M A C H I N E I N T E R F A C E I N S TA L L A T I O N The LC3000 Laundry Reader supports 60 wireless laundry machine connections. Laundry machines communicate with the wireless laundry network using Laundry Wireless Interfaces. The Laundry Wireless Interface (LWI) is a wiring harness and wireless module. The LWI communicates with the Laundry Reader via a Wireless Bridge(s) (LE3/ BRIDGE).
WIRELESS LAUNDRY MACHINE INTERFACE INSTALLATION Wireless Bridge LE3/BRIDGE Installation The LE3/Bridge module must be configured prior to being installed. This requires programming a network ID and configuring the module as a Bridge. Configure the LE3/BRIDGE 1 Apply power to the LC3000 Reader and make sure that it is online. 2 Install the configuration cable (p/n 044-042-043) into the RJ-12 Jack labeled LWI CONFIG. This cable is supplied with the LE3/BRIDGE.
WIRELESS LAUNDRY MACHINE INTERFACE INSTALLATION 1 Select the appropriate hardware and mount the LE3/BRIDGE enclosure. 2 Install 1/2” PVC conduit from the LC3000 to the enclosure. 3 The LE3/BRIDGE includes two configuration cables (p/n 044-042043). This cable has an RJ-45 connector and a 22-pin Molex connector. Plug the 22-pin connector into the Bridge module. 4 A patch cable is required to span the distance between the LE3/ BRIDGE enclosure and the LC3000 Reader.
WIRELESS LAUNDRY MACHINE INTERFACE INSTALLATION 3 Plug the 22-pin connector into the mating connector of the LWI module. The LC3000 Reader will detect the LWI module. The top two lines of the display show the machine ID, software version and network ID. The factory default for the network ID and machine ID is FF. If the LWI module has previously been assigned, the message Already Assigned is displayed. In all cases, enter 1 for yes, to reassign the network ID and/or machine ID. 4 Set the Network ID.
WIRELESS LAUNDRY MACHINE INTERFACE INSTALLATION If installing inside the hood compartment, keep the module away from the control board and any potential electrical interference sources. 5 Use the wire ties and wire tie blocks included with the LWI3010 to dress the wires within the compartment. 6 Re-install the operator console on the machine.
WIRELESS LAUNDRY MACHINE INTERFACE INSTALLATION 3 Install the two Molex pins connected to the Orange and Blue wires on the wiring harness into the two open positions of the transformer’s secondary output connector. This is an AC output, so the pins are interchangeable. 4 Install the 22-pin connector of the wiring harness onto the LWI3020 wireless module.
APPENDIX APPENDIX F EATURES • Interfaces to: Maytag commercial “debit-card” ready, Speed Queen NetMaster and MDC, and Whirlpool Advantech laundry machines • TCP/IP and wireless protocols encrypted using AES • Configuration via keypad/display, CONFIG port or telnet • Keypad (Service Card) configuration can be disabled • Telnet access can be disabled • Stores up to 40,000 transactions offline • Displays balance, account warnings and other messages following transactions • Adjustable volume set
TRANSACTION PROCESS TRANSACTION PROCESS The LC3000 Laundry Reader displays cardholder instructions. When idle, the reader display toggles between instructions and machines available. Offline messages are only displayed if offline operations are allowed in the reader configuration at the host and card number is valid. Transaction Process 1 Select a machine by using the Reader’s numeric keypad, and press Enter.
MANAGER MENUS M ANAGER MENUS The Manager Card is used to access LC3000 Laundry Reader menus for sales data and modifying reader settings. Manager Menus Swipe Manager Card 1. Sales Totals 2. Terminal Setup 3. Machine Service 4. Bridge Status 5. LCM20 Status Sales Total Card Interval $ Card Interval # Card Total $ Card Total # Terminal Setup Display Backlight (Off, Low, Medium, High) Display Contrast (Decrease, Increase) Volume Setup (Decrease, Increase) Machine Service 1. Set In/Out of Service (1-60) 2.
LAUNDRY COMPONENTS DIMENSIONS AND WEIGHT L AUNDRY COMPONENTS DIMENSIONS AND • LC3000: 9.6" H x 7.92'' W x 3.3" D, 7.6 lbs. • LE3/PSENCL: 9.6" H x 7.92" W x 3.3" D, 7.6 lbs. • LE3/BRIDGE: 4.5" H x 4.5" W x 2" D, 1.0 lb. • LWI30XX: 3" H x 3" W X 1.5" D, 1.0 lb. WEIGHT 9.660'' 8.940'' 8.840'' Mount ACMAIN Mount 6.360'' 3.360'' Mount Mount 0.940'' 0.000'' 7.920'' 7.220'' 6.270'' 4.200 1.200 0.720'' 0.
LAUNDRY COMPONENTS DIMENSIONS AND WEIGHT LC3000 Component Specifications Power Input Voltage Range Input Frequency Input Current 120VAC 60Hz 1.4A, max Operating Environment Temperature Relative Humidity Altitude 0 to +45C (+32 to +114F) 0 to 95 percent, non-condensing 0 -10,000 feet Non-Operating Environment Temperature Relative Humidity Altitude -20 to +70 C (-4 to +158F) 0 to 95 percent, non-condensing 0 - 35,000 feet Power Input Voltage Range Input Frequency Input Current 120VAC 60Hz 1.
LC3000 LAUNDRY READER DEFAULT CONFIGURATION SETTINGS LC3000 LAUNDRY READER D EFAULT CONFIGURATION S ETTINGS The LC3000 Laundry Reader’s default settings are: • DHCP enabled • NP (host) IP address assigned by DHCP server Restore Default Settings Forget your password? Restore Default Settings. 1 Connect a cable from a computer’s serial port to the one labelled “RS-232 CONFIG”. Cable connections are shown in RS-232 Config Port Connections (page 8).
MW9010/MW9012 LAUNDRY READER RETROFIT MW9010/MW9012 LAUNDRY READER RETROFIT BbTS Unix laundry centers with existing MW9010/MW9012 Laundry Readers can upgrade to the LC3000 Laundry Reader. Upgrading the Reader does not require wiring, LCM2s or laundry machine interface replacements. The LC3000, as shipped from Blackboard, is configured for up to 60 machines on up to 3 LCM20s.