User`s guide

ManualsBrandsBlack Box ManualsMedia ConverterLPS1000A

LPS1000A User’s Guide

The LPS1000A media converters enable

businesses to provide power to network

devices over the existing CAT5 data

connection. The LPS1000A AC powered PoE

media converters combine data received over a

fiber optic link with -48VDC power, provides

power to Data Terminal Equipment (DTE) and

Power Devices (PD) over unshielded twisted

pair cable. These PoE converters are Power

Sourcing Equipment (PSE) and are fully compatible with Powered Devices (PD) that

comply with the IEEE802.3af standard. In addition, these converters have PD signature

sensing and power monitoring features per the IEEE 802.3af standard.

NETWORK SERVICES

Product Description/Features . .2

Enclosure Mounting . . . . . . . . . .5

DIP Switches . . . . . . . . . . . . . . .6

Cable & Power Connections . .8

Internal Jumpers . . . . . . . . . . .10

Operations . . . . . . . . . . . . . . .11

Cable Specifications . . . . . . . . .12

Technical Specification . . . . . .13

Troubleshooting . . . . . . . . . . .14

Compliance Information . . . . .18

*Cable distances are the typical maximum cable distance. Actual distance is dependent

upon the physical characteristics of the network installation.

Mounting options (sold separately)

Part Number Description

LPS1000-Wall Wall Mount Bracket

LPS1000-DINRAIL DIN Rail Mtg. Bracket

Part Number Port One - Copper

10/100/1000Base-T

Port Two - Fiber

LPS1000A-MM RJ-45

100 m (328ft.)*

SC, 1000Base-SX, 850 multimode

62.5μm: 220m

(

722ft

)

50μm: 550m

(

1804ft)

LPS1000A-SM RJ-45

100 m (328 ft.)*

SC, 1000Base-LX, 1310 single mode

10km (6.2 miles)

LPS1000A-1SFP RJ-45

100 m (328 ft.)*

100/1000Base-X

SFP slot (empty)

LPS1000A-2SFP RJ-45

100 m (328 ft.)*

(2) 100/1000Base-X

SFP slots (empty)

Summary of content (11 pages)

PAGE 1
NETWORK SERVICES LPS1000A User’s Guide The LPS1000A media converters enable businesses to provide power to network devices over the existing CAT5 data connection. The LPS1000A AC powered PoE media converters combine data received over a fiber optic link with -48VDC power, provides power to Data Terminal Equipment (DTE) and Power Devices (PD) over unshielded twisted pair cable.
PAGE 2
LPS1000A Product Description & Features Product Description & Features -- Continued Description -- continued Description LPS1000A-2SFP LPS1000A-MM/-SM Fiber Link Active LED Power LED Fiber Port TP Link Active LED Duplex Power Over RJ-45 Port Ethernet LED Power LED Fiber Link Active LEDs PWR PWR LACT 100/1000 Base-X LACT LACT DUP 10/100/1000 Base-T POE PWR ERROR DUP PORT 1 Rear Panel 8-Position Switch LPS1000A-1SFP Power LED PWR Fiber Link Active LED POE PWR ERROR Power Inlet Rear
PAGE 3
LPS1000A Product Description & Features -- Continued Product features -- continued Over Current Protection/Under Current Detection (IEEE802.3af) Link Pass-Through The Link Pass-Through allows the media converter to monitor both the fiber and copper RX (receive) ports for loss of signal. In the event of a loss of an RX signal on one media port, the media converter will automatically disable the TX (transmit) signal of the other media port, thus, “passing through” the link loss.
PAGE 4
LPS1000A DIP Switches Installation -- Continued CAUTION: All installation and service must be performed by qualified service personnel. Read and follow all warning notices and instructions marked on the product and included in this manual. Setting the configuration switches -- continued LPS1000A-2SFP SW1. TP Auto-Negotiation: UP = Enable, DOWN Disabled Setting the configuration switches The configuration switches are located on the back panel of the LPS1000A media converters.
PAGE 5
LPS1000A Cable & Power Connections CAUTION: Associated Ethernet wiring shall be limited to inside the building. Failure to observe this caution could result in damage to the connected equipment. Cable & Power Connections -- Continued Installing the copper cable 1. Locate 10/100/100Base-TX copper cables with male, RJ-45 connectors installed at both ends. See Figure below. 2. Connect the RJ-45 connector at one end of the cable to the RJ-45 port on the media converter. Installing the fiber cable 1.
PAGE 6
LPS1000A Internal Jumpers Operation Power over Ethernet (PoE) LEDs The LPS1000A media converter transmits electrical power along with data to remote devices over standard twisted-pair cable in an Ethernet network. See individual LPS1000A faceplate for LED placements. The table below explains what the LED functions indicate. Note: Legacy powered devices that are not IEEE802.3af compliant can be power provided that the polarity matches that list below.
PAGE 7
LPS1000A Cable Specifications Technical Specifications The physical characteristics must meet or exceed IEEE 802.3™ specifications. Standards: Copper cable Category 5: (Minimum Requirement) Gauge: 24 to 22 AWG Attenuation : 22.0 dB /100m @ 100 MHz • Straight-through OR crossover twisted-pair cable may be used. • Shielded twisted-pair (STP) OR unshielded Twisted-pair (UTP) may be used. • Pins 1&2 and 3&6 are the two active pairs in an Ethernet network .
PAGE 8
LPS1000A Technical Specifications -- continued IMPORTANT: Copper based media ports, e.g., Twisted Pair (TP) Ethernet, USB, RS232, RS422, RS485, DS1, DS3, Video Coax, etc., are intended to be connected to intra-building (inside plant) link segments that are not subject to lightening transients or power faults. Copper based media ports, e.g., Twisted Pair (TP) Ethernet, USB, RS232, RS422, RS485, DS1, DS3, Video Coax, etc.
PAGE 9
LPS1000A Declaration of Conformity Declaration of Conformity NETWORK SERVICES Name of Mfg: Black Box Corporation 1000 Park Drive, Lawrence PA U.S.A. Model: LPS1000A Series Media Converters Part Number(s): LPS1000A-MM, LPS1000A-SM, LPS1000A-1SFP, LPS1000A-2SFP Regulation: EMC Directive 89/336/EEC Purpose: To declare that the LPS1000A to which this declaration refers is in conformity with the following standards.
PAGE 10
LPS1000A Compliance Information CE Mark FCC regulations This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
PAGE 11
LPS1000A Trademark notice All registered trademarks and trademarks are the property of their respective owners. Copyright restrictions © 2009 Black Box. All rights reserved. No part of this work may be reproduced or used in any form or by any means graphic, electronic, or mechanical - without written permission from Black Box. 20 Printed in the U.S.A. 33436.