LGC300A-R2 Industrial SFP/SFP Multi-Power Mode Converter Converts any fiber optics type interface to any other fiber optics type interface.
FCC and IC RFI Statements FCC and Industry Canada RF Interference Statements Class B Digital Device. This equipment has been tested and found to comply with the limits for a Class B computing device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation.
Certifications Certifications Class 1 Laser product, Luokan 1 Laserlaite, Laser Klasse 1, Appareil A’Laser de Classe European Directive 2002/96/EC (WEEE) requires that any equipment that bears this symbol on product or packaging must not be disposed of with unsorted municipal waste. This symbol indicates that the equipment should be disposed of separately from regular household waste.
Table of Contents Table of Contents Part Numbers ...................................................................................................... 5 1. Specifications ......................................................................................... 6 1.1 Standards/Compliance ........................................................................... 6 2. Overview: About the Industrial SFP/SFP Multi-Power Mode Converter.............................................................................
Part Numbers Part Numbers Part Number LGC300A-R2 LGC300A-R2 Description MultiPower SFP to SFP Mode Converter (SFPs sold separately) 724-746-5500 | blackbox.
Chapter 1: Specifications 1. Specifications DC Input +7 VDC to +50 VDC @ 2.5 watts. Actual current consumption may vary depending on the type of SFP modules installed. When not using the supplied AC/DC converter the externally supplied DC power must be provided from a LPS source. 100 to 240 ±10% VAC input, 5 VDC output @ 2A max.
Chapter 2: Overview 2. Overview: About the Industrial SFP/SFP Multi-Power Mode Converter The Industrial SFP/SFP is a pure mode converter that converts any fiber optics type to any other fiber optics type. This product is a Protocol independent converter and is not intended for applications that require retiming or any Layer 2 functions. The Industrial SFP/SFP supports extended temperature operation.
Chapter 3: Install the Industrial SFP/SFP Multi-Power Mode Converter 3. Install the Industrial SFP/SFP Multi-Power Mode Converter The Industrial SFP/SFP Multi-Power Mode Converter installs anywhere as a standalone, table-top device or on a DIN rail. As a standalone device, install it in locations with limited space. If multiple connections are required, use an IE-PowerTray/18 enclosure (sold separately). The tray allows for 18 conversions in a 1.5 rack unit of space.
Chapter 3: Install the Industrial SFP/SFP Multi-Power Mode Converter • • User supplied LPS DC power via a four-position DC power block. Power from an Power Tray 18-Slot DC For extended temperature operation the DC terminal block must be used because the supplied AC to DC converter is not rated for extended temperature operation. The power source used with the DC terminal block should be a Limited Power Source (LPS). 3.3.
Chapter 3: Install the Industrial SFP/SFP Multi-Power Mode Converter 3.4 DC Power Supply Precautions The following precautions must be observed when installing the chassis model with an internal DC power supply. 1. Check nameplate ratings to ensure there is no overloading of supply circuits that could effect overcurrent protection and supply wiring. 2. In addition, the following must be observed: a.
Chapter 4: Operation 4. Operation 4.1 LED Operation The Industrial SFP/SFP contains four status LED indicators. Each LED is dual color and has three states: off, red, or green. A loss of signal on one SFP causes the TX of the other SFP to turn off. This action does not activate the red TX Fault LED. LED Color or State OFF Red PWR SD I SD 2 Card does not pass the self-test. Unit does not have power. Power is applied to the card. All internal self-test functions must pass before the PWR LED is green.
Chapter 5: Contacting Black Box 5. Contacting Black Box Black Box Customer Service Order toll-free in the U.S.: Call 877-877-BBOX (outside U.S. call 724-746-5500) Free technical support, 24 hours a day, 7 days a week. Call: 724-746-5500 or Fax: 724-746-0746 Mail order: Black Box Corporation 1000 Park Drive, Lawrence, PA 15055-1018 Web site: www.blackbox.com E-mail: info@blackbox.com WARNING Disconnect all power supplies before servicing. Page 12 724-746-5500 | blackbox.
Chapter 6: Fiber Optic Cleaning Guidelines 6. Fiber Optic Cleaning Guidelines Fiber Optic transmitters and receivers are extremely susceptible to contamination by particles of dirt or dust, which can obstruct the optic path and cause performance degradation. Good system performance requires clean optics and connector ferrules. 1.
Chapter 7: Electrostatic Discharge Precautions 7. Electrostatic Discharge Precautions Electrostatic discharge (ESD) can cause damage to any product, add-in modules or stand alone units, containing electronic components. Always observe the following precautions when installing or handling these kinds of products. 1. Do not remove unit from its protective packaging until ready to install. 2. Wear an ESD wrist grounding strap before handling any module or component.
Notes LGC300A-R2 724-746-5500 | blackbox.
LGC300A-R2 Rev. 1 55-80619BB-00 Rev.
