Instruction Manual

ManualsBrandsBK Electronic Design ManualsElectronicsWIFI and Bluetooth Module

USA FCC / Canada IC Compliance Information

Notices for Original Equipment Manufacture (OEM):

This equipment is certiﬁed for mobile and base radio applications. If the equipment is used for

portable applications, it must undergo SAR testing.

The equipment has been certiﬁed by the FCC / IC for use with other products without any

further certiﬁcation of equipment (as per FCC section 2.1091). Modiﬁcations not expressly

approved by BK Electronic Design Inc. could void FCC / IC certiﬁcation and authority to use this

equipment.

Final product, which includes this equipment shall be tested to comply with unintentional

radiators (FCC section 15.107 & 15.109) before declaring compliance to Part 15 of the FCC

Rules. Other compliance testing may also apply.

This FCC and IC certiﬁcation is not valid and the FCC ID or IC number cannot be used on the

ﬁnal product, when requirements outlined below are not met or if the module is colocated with

other transmitters. In these circumstances, the OEM integrator is responsible for reevaluation of

the end product, which includes this transmitter reevaluation for obtaining a separate FCC and

IC authorizations.

USA FCC Approval

This equipment complies with Part 15 of the FCC rules and regulations. Limits of FCC rules are

designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses, and can radiate radio frequency energy. If this

Equipment is not installed and used in accordance with the instruction manual, it may cause

harmful interference to radio communications. There is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by taking following measures: reorient or relocate

antenna; increase the separation distance between this equipment and receiver; connect the

equipment into an outlet on a circuit different from that to which the receiver is connected;

consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two

conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause

undesired operation.

BK Electronic Design Inc.

www.bkelectronicdesign.com

Page  of 1 5

Summary of content (5 pages)

PAGE 1
USA FCC / Canada IC Compliance Information Notices for Original Equipment Manufacture (OEM): This equipment is certified for mobile and base radio applications. If the equipment is used for portable applications, it must undergo SAR testing. The equipment has been certified by the FCC / IC for use with other products without any further certification of equipment (as per FCC section 2.1091). Modifications not expressly approved by BK Electronic Design Inc.
PAGE 2
Canada IC Approval (English) The radio transmitter (IC: 25136-WL18DBMOD) has been approved by Industry Canada to operate with the antenna types listed with the maximum permissible gain for each antenna type indicated. It is strictly prohibited to operate Equipment with antenna types not included in this list or having a gain greater than the maximum gain indicated for that type.
PAGE 3
USA FCC/ Canada IC Requirements: If following “WiFi/ Bluetooth Antenna Requirements” (with or without colocated LTE module) and “Colocated LTE Antenna Requirements“ (when final product is equipped with colocated LTE module) cannot be met, the FCC/IC authorization will not be considered valid and it is prohibited to use current FCC ID/IC ID on the final product.
PAGE 4
Colocated LTE Antenna Requirements: • If the final product contains LTE Cellular Module, the maximum Effective Isotropic Radiated Power (EIRP) of LTE Module (which combines maximum conducted power of transmitter, transmission line loses, connector, cable losses and antenna gain) must not exceed the power levels specified in the Table 2. • Antenna gains for each bands shall not exceed gains, which are specified in the specific LTE module Grants/certificates issued by USA FCC and ISED Canada.
PAGE 5
Requirements for OEM Documentation All the CAUTION statement below must be included in OEM manuals and product documentation in order to alert user about FCC and IC compliance requirements. Omission of these statements in OEM manuals invalidates OEM leveraged certifications.