Pe rgola I n stru ctions Also find Installation Instructions at bjornwoodworks.
PERGOLA Recommended Tools Drill with 1/2” Socket Bit 1/8” Wood Drill Bit Tape Measure Level Pencil Step Ladder BJORNWOODWORKS.
PERGOLA Parts A. B. C. *D. PARTS A. Shoulder Bracket B. Boot C. Hex Head Lag Bolt 2” D. 4x4 Lumber * Not Included (must be purchased separately) NOTE BJORNWOODWORKS.com 2020 3 VERSION 01 Get lumber at your local hardware store. For recommendations on installations involving brick or stone, see the end of this installation guide.
PERGOLA Installation Instructions STEP 1 Lay out the rug or tarp so you don’t scratch or mar your parts. Then place your parts as shown in the Top View. Make sure that the shoulder bracket is oriented correctly, the leg with the back stop should be facing up. STEP 2 Using a pencil, mark each piece of wood 6 inches in from the end. Slide each piece of wood into corner brackets where you marked the line as show in the Top View. NOTE Keep wood centred in all brackets while tightening lag bolts.
PERGOLA Installation Instructions STEP 3 Using your drill and 1/8 inch bit, pre-drill the holes and then screw in lag bolts using a 1/2 in socket wrench or socket drill bit. SUGGESTION Please flip all pieces over for next steps. Slide remaining pieces of wood into the remaining corner bracket and repeat step 1.3 above to secure corner pieces. BJORNWOODWORKS.
PERGOLA Installation Instructions STEP 5 Using your drill and 1/8 inch bit, pre-drill the holes and then screw in lag bolts using a 1/2 in socket wrench or socket drill bit. STEP 6 Fit two pieces together VERSION 01 BJORNWOODWORKS.
PERGOLA STEP 7 Using your drill and 1/8 inch bit, pre-drill the holes and then screw in lag bolts using a 1/2 in socket wrench or socket drill bit. With the help of two other people raise one side of the roof as shown in step 2.1. Then insert the first leg into corner bracket. Install both legs on this side while propped up. BJORNWOODWORKS.
PERGOLA STEP 9 Using your drill and 1/8 inch bit, pre-drill the holes and then screw in lag bolts using a 1/2 in socket wrench or socket drill bit. VERSION 01 BJORNWOODWORKS.
PERGOLA STEP 10 Install remaining leg and secure with lag bolts. VERSION 01 BJORNWOODWORKS.
PERGOLA STEP 11 With help, raise each leg and slide into the boot bracket. VERSION 01 BJORNWOODWORKS.
PERGOLA STEP 12 Using your drill and 1/8 inch bit, pre-drill the holes and then screw in lag bolts using a 1/2 in socket wrench or socket drill bit. VERSION 01 BJORNWOODWORKS.
PERGOLA STEP 13 Make sure that your legs measure equal distance apart in preparation for securing to the ground. VERSION 01 BJORNWOODWORKS.
PERGOLA STEP 14 Make sure legs are level and at a 90º angle using a level. VERSION 01 BJORNWOODWORKS.
PERGOLA STEP 15 Secure boot bracket to ground using concrete, brick, stone, or wood bolts and adapters (not included in kit). VERSION 01 BJORNWOODWORKS.
PERGOLA Finished You are now ready to enjoy your new Bjorn Outdoor Pergola kit, now get out and enjoy outdoor living. VERSION 01 BJORNWOODWORKS.
PERGOLA Installing on Concrete, Brick or Stone Installation on a concrete, brick or stone will require additional tools and hardware. For example, drill bits for drilling into stone and mortar are different from standard drill bits, and you may need a heavy duty drill: Masonry Drill Consult with a local hardware store for the correct hardware and equipment to use. VERSION 01 BJORNWOODWORKS.
PERGOLA VERSION 01 BJORNWOODWORKS.
Follow us on social media for inspiration support@bjornwoodworks.