User's Manual SPP-R210 Mobile Printer Rev. 1.00 http://www.bixolon.
SPP-R210 ■ Table of Contents ※ Manual Information & Usage Precautions ························································ 3 1. Content Confirmation ··················································································· 10 2. Product Part Names ····················································································· 11 3.
SPP-R210 ■ Manual Information ※ Manual Information & Usage Precautions This user’s manual contains basic information for product usage as well as for emergency measures that may be required. ※ The following separate manuals provide more detailed content on various technological issues and areas. 1. Windows CE Module Program Manual This manual provides information on the dll files required for Windows CE application program development. 2.
SPP-R210 ■ Safety Precautions In using the present appliance, please keep the following safety regulations in order to prevent any hazard or material damage. WARNING Violating following instructions can cause serious injury or death. Do not plug several products in one multi-outlet. • • • • You must use only the supplied adapter. This can provoke over-heating and a fire. If the plug is wet or dirty, dry or wipe it before usage. If the plug does not fit perfectly with the outlet, do not plug in.
SPP-R210 CAUTION Violating following instructions can cause slight wound or damage the appliance. If you observe a strange smoke, odor or noise from the printer, unplug it before taking following measures. Keep the desiccant out of children’s reach. • If not, they may eat it. • Switch off the printer and unplug the set from the mains. • After the disappearance of the smoke, call your dealer to repair it. TO UNPLUG PROHIBIT PRINTER Install the printer on the stable surface.
SPP-R210 ■ Battery Safety Precautions Make sure to review the user manual carefully prior to product use. Neglecting to heed the following instructions can result in battery overheating, combustion, explosion, damage and/or decline in performance and product life. Danger 1. Do not allow water, seawater or moisture to enter or leak into the battery.
SPP-R210 10. Do not pierce the battery with a pointed object, such as nail or awl, or strike with a heavy object, such as a hammer, and take care not to step on the battery. There is a potential risk of battery overheating, combustion, and/or explosion caused by an internal short circuit. 11. Do not solder the battery directly. Doing so may melt the insulating materials and/or damage the safety mechanism or safety equipment, resulting in battery overheating, combustion, and/or explosion. 12.
SPP-R210 Caution 1. Do not use or leave the battery in a location exposed to high temperatures or intense direct sunlight, such as within an automobile. Doing so can cause battery overheating and/or combustion. In addition, battery performance and product life may be reduced. 2. The battery contains a safety mechanism to prevent danger.
SPP-R210 Recommended 1. Review the user manual for instructions concerning insertion/removal of batteries into/from the product. 2. The battery shipped with the product is partially charged, and it is good for checking the operation of the equipment. Charge the battery first with the supplied charger if the equipment does not work or long hours of operation are required. 3. To avoid improper use of the battery, review the product user manual carefully. 4.
SPP-R210 1. Content Confirmation The following items should all be contained in the printer package. Contact the dealer from which the purchase was made if any item is damaged and/or missing. ※ Basic items SPP-R210 Power Cord Battery Pack Battery Charger Belt Clip Paper CD ※ Optional items Belt Strap Vehicle charger Interface Cable Cleaning Pen Battery Pack_V2 (with outer contacts) Single Battery Cradle Quad Battery Charger Wall Mount (RWM-350) (for Quad Battery Charger) Rev. 1.
SPP-R210 2. Product Part Names • Front Paper Cover Power Button Open button Paper Feed Button MSR Slot • Rear Hole for mounting belt strap / belt clip Battery Cable Connection Power Connection Rev. 1.
SPP-R210 3. Installation & Usage 3-1 Battery Installation 1) Insert the battery on the rear side of the printer, aligning the battery hook properly. 2) Push the battery into the slot until a snapping sound is heard. NOTE As the battery is not charged at the time of purchase, charge the battery prior to product use. (Use the battery charger) 3-2 Battery Charging 3-2-1 Using Battery Charger 1) Turn off the printer power. 2) Connect the power cord ② to the battery charger ①, and then connect AC power.
SPP-R210 3-2-2 Using Single Battery Cradle (Optional) ③ ④ 1) Connect the power cord ② to the battery charger ①. 2) Connect the battery charger ① to power connector of the single battery cradle ③. ③ ① ② 3) Plug the power cord outlet. 4) Insert the battery battery cradle is heard. ② ④ single into the ③ 3-2-3 Using Vehicle Charger (Optional) 1) Turn off the power to the printer. 2) Connect the vehicle charger ① to your car’s cigarette lighter jack.
SPP-R210 3-2-4 Using Quad Battery Charger / Quad Docking Cradle (Optional) 3-2-4-1 Connecting the cables 1) Connect the power cord to the adaptor, and Connect the adaptor to the power connector of the quad battery charger / quad docking cradle. 2) Plug the power cord into a power Outlet. Input power is 100 ~ 240VAC, 50/60Hz, 1.0A. 3) When the power is supplied, the yellow, green and red lamps are on for three seconds and do the self-test. WARNING Use only designated AC/DC adaptor. (12VDC, 3A) Rev. 1.
SPP-R210 3-2-4-2 Charging Battery (Printer) 1) Fasten batteries via the battery hooks into the quad battery charger as shown above. 2) Push the battery in until a snapping sound is emitted. 3) Charging begins as soon as the battery is completely inserted. (Batteries are charged to 8.4VDC, 0.8A.) 4) Push the hook and pull up to extract the battery. NOTE Battery charging status descriptions are as follows.
SPP-R210 3-3 Paper Installation 1) Press the Open button to open the paper cover. 2) Insert the paper as shown in the image. (Remove any remaining core of a fully used paper roll.) 3) Take care to align the paper correctly. 4) Pull the paper out as shown in the image and close the paper cover. 5) Tear off any excess paper in the direction of the side of the printer. Rev. 1.
SPP-R210 3-4 Using Belt Strap 1) Insert the belt strap screw into the belt strap hole. Belt Strap Coin Belt 2) Use a coin to tighten the belt strap screw as shown in the image. 3) Undo the belt strap Velcro. 4) Fasten the belt strap to a belt. 5) Close the Velcro as shown in the image. Belt Rev. 1.
SPP-R210 3-5 Using Belt Clip (Optional) 1) Insert the screw of the belt clip to the belt clip mounting hole. Coin Belt Clip 2) Fasten the screw of the belt clip with an object like a coin as shown in the picture. (Be careful to fasten in the correct direction.) 3) Insert the clip to the belt. Belt Rev. 1.
SPP-R210 3-6 Using Control Panel • Power Button This button is used to turn the printer on and off. 1) When the printer is off, pressing this button for approximately 2 seconds will turn the power on. 2) When the printer is on, pressing this button for approximately 2 seconds will turn the power off. • Paper Feed Button This button is used to feed paper manually, take the self-set and dump hexadecimals. 1) To feed paper manually, press this button. 2) For information on the self-test, refer to “4.
SPP-R210 3-7 Using MSR 1) Insert the card as shown in the image and swipe in the direction of the arrow. (can be done in both directions) NOTE If the card does not register, first check to see if it is properly aligned. When swiping the card, the recommended swiping speed is 100 ~ 1200 mm/sec. 4. Self-Test Run the self-test when first setting the printer or when encountering a problem, and check the following.
SPP-R210 • Self-Test Sample (For Bluetooth) Firmware version : V01.00 STOBa 010114 Butter Capacity : 64K Bytes USB 2.0 Interface Print Density : 100% Default Codepage : PC437 Print Speed : Max. 80mm/s Double byte character mode:On Font : 12 x 24 Paper out Bell : Off Low Battery Buzzer : On Power off time : 15 Min Idle mode time : 10 Sec MSR data including sentinel Character mode : None MSR read mode : Auto TRACK1/2/3 BATT NTC : OK If you want to continue SELF-TEST printing, Please press FEED button.
SPP-R210 • Self-Test Sample (For Wireless LAN) Firmware version : V01.00 STOBa 010114 Butter Capacity : 64K Bytes USB 2.0 Interface Print Density : 100% Default Codepage : PC437 Print Speed : Max. 80mm/s Double byte character mode:On Font : 12 x 24 Paper out Bell : Off Low Battery Buzzer : On Power off time : 15 Min Idle mode time : 10 Sec MSR data including sentinel Character mode : None MSR read mode : Auto TRACK1/2/3 BATT NTC : OK If you want to continue SELF-TEST printing, Please press FEED button.
SPP-R210 5. Label Printing Function 5-1 Label Function Setting Label paper and black mark paper available at the label mode. • Setting Operations 1) Turn on the printer power. 2) Open the paper cover and press and hold down the paper feed button for longer than two seconds. 3) After the buzzer tone is emitted, insert paper and close the cover. 4) Repeat the steps above to return to receipt mode. • Setting Via Memory Switch - Please refer to the memory switch changing section of the Commands Manual.
SPP-R210 6. iOS MFi Mode Setting (Optional) This product supports MFi mode that enables Bluetooth communication with iOS devices. (Applicable to MFi support models only) • How to enable and disable MFi mode 1) Turn on the printer. 2) Open the paper cover and press the power button and paper feed button at the same time for longer than two seconds. 3) Close the cover when the buzzer sound is heard. 4) Reboot the printer when the following message is printed.
SPP-R210 7. Peripherals Connection This product can communicate with other devices via Bluetooth communication and cable. 7-1 Bluetooth & Wireless LAN Connection 1) The printer can be connected to devices equipped with Bluetooth communication capacity (PDAs, PCs, etc.). 2) Use the Bluetooth connection function supported by the device to connect to the printer.
SPP-R210 8. Printer Cleaning If the interior of the printer is dusty, print quality can decline. In such a case, follow the instructions below to clean the printer. A Head B Sensor 1) Open the paper cover and remove the paper if there is any. Apply the cleaning pen from the center to the edge over the printer head (A) for cleaning. 2) Clean the printer head (A) using the cleaning pen. 3) Remove paper dust from the paper detection sensor (B) using the cleaning pen.
SPP-R210 9.
SPP-R210 9-2 Certification 1) WEEE (Waste Electrical and Electric Equipment) This mark shown on the product or its literature indicates that the corresponding item should not be discarded at the end of its working life with other household waste. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate marked items from other types of waste and recycle them responsibly to promote the sustained reuse of material resources.
SPP-R210 Disposal Directions • Do not dispose of waste battery packs recklessly. • Do not burn or throw in fire to dispose of the battery pack. There is a risk of fire and/or explosion. • How to dispose of battery packs may vary depending on countries or regions. Dispose of it in the correct method. Recommendation for Charging • Do not charge your battery pack in a way not mentioned in the instruction manual. Doing so may result in fire or explosion.