ZN-302 A/S/AS USER MANUAL
NOTES: Thank you for purchasing our product. Our systems have all been designed and tested to be compatible with the earliest to latest vehicles available throughout the world. Our primary goal was to provide a reliable and stable product. Our secondary goal was to ensure that our systems are easy to install. Our final goal was to provide features that would benefit the user and installer. We are confident that our products will meet and exceed your expectations.
NOTES: CAUTION! PLEASE READ CAREFULLY The user and installer should completely read the User Manual, Installation Manual, and the vehicle’s manual completely before installing and operating this system. Not reading the manuals completely may result in injury or damage to the user(s), installer(s), and/or the vehicle.
CONTENTS WARRANTY CARD 1. Introduction 1.1 1.2 1.3 1.4 System Contents Remote Control Button Layout Remote Control Battery Replacement Remote Control Button Introduction (Primary/Secondary) 6 7 8 9 2. Primary Features 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.
3.16 SHOCK SENSOR ON/OFF The Shock Sensor can be turned ON or OFF via the remote control. To turn ON or OFF the shock sensor, follow the Button Sequence: Hold Brake Pedal and than press Function Button 3 times and than press Unlock Button once. Do the same procedure again to toggle between ON and OFF. 3.17 Z-PASS TOUCH The system can be armed or disarmed by “touching” the Z-Pass Touch with a PIN of 4 - 10 digits. 1. PIN Registration a. Turn Key to ON position (Engine OFF) b.
1.
1. 2. 3. 4. 5. 6. 7. 8. 9. While the engine is running, hold down Brake Pedal Press and hold Remote Start Button for 2 seconds. You will see 6 parking light flashes. You will see alternating BLUE and RED LED flashes on the remote control. You will hear 6 siren chirps and remote control beeps. Engage the parking brake Turn the key to the OFF position and vacate the vehicle without pressing the brake pedal. 1.2 Remote Control Button Layout Press and release . You will see 6 parking light flashes.
1.3 Remote Control Battery Replacement Turbo Timer ON Slide out the battery tray. Vehicle 1 parking light flashes & 1 x BLUE LED flash & 1 Remote Control 1 siren chirp beep Turbo Timer OFF Vehicle 2 parking light flashes & 2 x BLUE LED flashes & Remote Control 2 siren chirps 2 beeps Turbo Timer AUTO (NORMAL) 1.Replace with CR2032 3V battery.
see 3 parking light and BLUE LED flashes. Cold or Hot Start Main Setting is now set to Cold.
Button(s) Duration temperature is hotter than a set temperature or colder than a set temperature. Description Press and release AUX 8 Function Button twice → Press and release Trunk Button 3. Hot Start Temperature This is the threshold temperature for the Hot setting. If the vehicle’s internal temperature goes above this value, the timer will start. Hold Brake Pedal → Passive Arm ON/ Press and release OFF Function Button three times → Press and release Lock Button 4.
Legend: 10. 11. You can program more features if desired. If you are finished programming, wait until you exit programming mode. The remote control BLUE LED will stop flashing quickly. Button Combination means to press (Default) Timer Setting Cold or Hot Start Main Setting Hot Start Temperat ure Cold Start Temperat ure : Function Button For example, Options Feature ~ : Press and hold button for 2 seconds. → : Press buttons in sequence (not together).
3.11 Cold/Hot Start Timer A timer can be set to remote start the car. Once activated, the vehicle will remote start automatically. The timer can be set to start every 1,2, 4, or 6 hours. However, a temperature constraint can also be added so that if the temperature reaches a certain level, the timer will start. There are 3 temperature constraints: HOT, COLD, HOT & COLD. If HOT is selected, the timer will start if the temperature is hotter than a specific temperature.
Alternatively, installing ZPASS TOUCH system will prevent accidental key lockouts. 2.1 Door Lock (Arm—302 A/AS) Press and release 3.9 Safety Relock (Rearm—302 A/AS) (Hold down brake pedal. Press and release Function Button 4 times and then press and release Lock Button) Successful Door Lock (Arm): If the system is in the armed state and the system is disarmed but a door is not opened, the system will Safety Rearm automatically within 30 seconds.
2.2 Door Unlock (Disarm—302A/AS) Press and release Remote control beep mute ON - Beeper OFF Remote Control All features of the system still function with remote control beep mute ON. Successful door unlock (disarm) Vehicle 1 BLUE LED flash & 1 beep 2 parking light flashes & Remote Control 2 siren chirps 2 BLUE LED flashes & 2 beeps Remote control beep mute OFF - Beeper ON 3 RED LED flashes & 3 beeps 3.
NOTE: Remote start reservation type can be changed through the User Programmable Options. 3.4 Temperature Status Press and hold 2.4 Vehicle Status Press and release The status of the vehicle will be displayed on the 2-way remote control. The following table describes the different situations. Please note the priority (top to bottom). If a status condition is met, any other conditions below it will not be checked.
Failed remote start: • • • 3.
Options Feature Diesel warm up time → Siren sound time → Turbo timer run time Remote start reservation Remote start run time Valet mode ON Button Combination → → → Vehicle 30 sec 15 sec 7.5 sec 70 sec 100 sec 1 min 2 min 5 min Automatic Manual 15 min 5 min 25 min For example, if siren sound time needs to be changed to 100 seconds, the following procedure would be used. 1. Press and release 2. 3. Press and release . You will see 1 parking light and 1 remote control BLUE LED flash.
3.1 User Programmable Options 1. Press and release 2. 3. Press and release . You will see 1 parking light and 1 remote control BLUE LED flash. You will also hear 1 siren chirp and 1 remote control beep. You are now in User Programming Mode. The remote control BLUE LED will flash quickly to signify that you are in programming mode. Follow the chart below for programming options. Press and release each button in the Button Sequence to enter the programming mode for the desired feature.