ZN-502 A/S/AS USER MANUAL
Thank you for purchasing our product. Our systems have all been designed and tested to be compatible with the earliest to latest vehicles available throughout the world. Our primary goal was to provide a reliable and stable product. Our secondary goal was to ensure that our systems are easy to install. Our final goal was to provide features that would benefit the user and installer. We are confident that our products will meet and exceed your expectations.
CAUTION! PLEASE READ CAREFULLY This device under provision section 15.21 of FCC Rule Part 15 that changes or modiications not epressly approved by the party responsible for compliance could avoid the user’s authority to operate the equipment. The user and installer should completely read the User Manual, Installation Manual, and the vehicle’s manual completely before installing and operating this system.
CONTENTS 1. Introduction 1.1 1.2 1.3 1.4 System Contents Remote Control Button Layout LCD Display Introduction Remote Control Button Introduction 6 7 8 9 2. Primary Features 2.1 2.2 2.3 2.4 2.5 2.6 2.7 Door Lock (Arm) Door Unlock (Disarm) Arm / Disarm Status Car Find & Status LCD Screen Status Panic Remote Start 11 11 11 12 12 12 13 2.8 2.9 Trunk Release Valet Mode 14 14 3. Secondary Features 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 3.10 3.11 3.12 3.13 3.14 3.15 3.16 3.
1. INTRODUCTION 1.1 1.2 1.3 1.
1.
1.2 Remote Layout Control Button Front View Antenna OLCD / UCLCD Buttons Battery 1.5 V AAA Back View Lock / Unlock 2-way Remote & Main Controller Specifications - Please see the page 26 1.
CAUTION NEVER use the system except for its intended use. This is an electronic system with complex circuitry. Avoid dropping the components or cause any other physical damage as that will void the warranty. 8 1.
Button(s) Duration* Description Ⅰ 0.5 sec Arm / Door Lock Ⅱ 0.5 sec Disarm / Door Unlock Ⅲ× 3 Times 0.5 sec Remote Control Hold ON/OFF Ⅳ 0.5 sec Vehicle Status / Car Finder Ⅰ- 2+ sec Panic Ⅲ- 2+ sec Remote Start Ⅳ- 2 sec Trunk Release Ⅱ~ 4 sec Time / Alarm / Remote Start Timer Set Ⅰ+Ⅳ 0.5 sec Remote Control Beep Mute ON/OFF Ⅱ+Ⅲ 0.5 sec Siren Mute ON/OFF Ⅰ+Ⅱ 0.5 sec Aux 1 Ⅲ+Ⅳ 0.
2. PRIMARY FEATURES 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 10 Arm (Door Lock) Disarm (Door Unlock) Arm / Disarm Status Car Find & Status LCD Screen Status Panic Remote Start Trunk Release Valet Mode 2.1 Door Lock (Arm) ButtonⅠ 0.
Successful Arm (Door Lock) Remote Control Vehicle & flash. 1 beep will occur. 1 parking light flash & 1 siren chirp Failed Arm (Door Lock) If a door, trunk and/or hood is open while arming, 4 siren chirps and 4 parking light flashes will occur immediately. Please ensure any doors, trunk and/or hood that is open, is closed. Rearm the system. 2.2 Door Unlock (Disarm) Button Ⅱ 0.5 sec Successful Disarm (Door Unlock) Remote Control Vehicle & occur. will flash.
2.4 Vehicle Status / Car Finder Button Ⅳ 0.5 sec 6 blinks & the vehicle’s inner temperature will be displayed. The Remote Control following status indications will be checked and displayed. If the status is normal, only the temperature will be displayed. 4 beeps will occur. Vehicle Open Door 6 parking light flashes & 6 siren chirps Open Hood Remote Start On Open Trunk Shock Sensor Trigger Option 1 Input Trigger 2.5 Remote Control Hold ButtonⅢ 0.5 sec x 3 Times Pressing Button Ⅲ 3 times for 0.
2.7 Remote Start ButtonⅢ 2+ sec Successful Remote Start & will blink until remote start is turned off. 1 beep will occur if the main Remote Control control module communicates with the remote control. 5 beeps will occur after remote start is successful. Vehicle 1 parking light flash & 1 siren chirp if the main control module communicates with the remote control. 5 parking light flashes & 5 siren chirps after remote start is successful.
2.8 Trunk Release Button Ⅳ 2 sec Remote Control Vehicle & & beeps will occur. will blink. 2 2 x parking light flashes & 2 siren chirps Trunk release will unlock the door(s) and disarm the system. NOTE: On manual transmission vehicles, trunk release will turn off remote start. 2.9 Valet Mode ButtonsⅠ+ Ⅲ 4 sec Valet Mode ON Remote Control Vehicle & will stay 1 parking light flash & 1 siren chirp & Remote Control OFF. Vehicle 1 will blink. ON. will blink.
3.SECONDARY FEATURES 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 3.10 3.11 3.12 3.13 3.14 3.15 3.16 3.
3.1 Remote Control Beep Mute ButtonsⅠ+ Ⅳ 0.5 sec Remote Control Beep Mute ON - Vibrate ON Remote Control Vehicle & stay ON. will blink. will 1 parking light flash & 1 siren chirp When Remote Control Mute is ON, the remote control will use vibration alerts. Remote control mute OFF - Beeper ON 3.2 Siren Mute ButtonsⅡ+ Ⅲ 0.5 sec Siren Mute ON - Siren OFF Remote Control Vehicle & will blink . will stay ON.
3.3 Passive Arm (Lock) ButtonsⅠ+Ⅱ 4 sec + Brake Pedal To activate or deactivate this function, the Brake Pedal must be held down at the same time while Buttons I + II are pressed for 4 seconds. Once a door is opened and closed and the system is not armed via the remote control, the system will automatically arm and lock the doors. The system will arm and lock the doors after 25 seconds of the last door closing. Every 5 seconds, 1 parking light flash and 1 siren chirp will occur.
3.5 Ignition Lock ButtonsⅠ+ Ⅳ 4 sec To activate or deactivate this function, the Brake Pedal must be held down at the same time while Buttons I + IV are pressed for 4 seconds. Ignition lock will lock the doors when the foot brake is pressed after the key is put into key cylinder and turned to the ON position. If a door is opened while the key is in the ON position, the doors will lock again once the door is closed and the foot brake is pressed again. Ignition Lock ON Remote Control & stay ON. will blink.
3.7 Turbo Timer ButtonsⅢ + Ⅳ 4 sec To activate or deactivate this function, the Brake Pedal must be held down at the same time while Buttons III + IV are pressed for 4 seconds. This feature will allow turbocharged or supercharged vehicles to cool down by idling the engine for a specified amount of time even though the key is turn to the OFF position. The engine will continue to idle. Turbo Timer ON Remote Control Vehicle & will blink. will stay ON.
3.9 Remote Control Registration 1. 2. 3. 4. Insert key and turn the key to ON position (engine is OFF). Press brake pedal 4 times. On the 4th press, hold the brake pedal down. 3 parking light flashes and 3 siren chirps will confirm remote control programming mode. 5. Press Button Ⅰ (Lock Button) . 6. After each remote control is added, there will be a confirmation of 2 parking light flashes and 2 siren chirps. You can add up to 3 2-way remote controls and 2 1-way remote controls per system. 7.
3.11 User Programmable Options Buttons Ⅲ + Ⅳ 2 sec When you enter programming mode by holding Buttons III + Ⅳ for 2 seconds, you will hear 1 remote control beep. The parking lights will flash 1 time and the siren will chirp 1 time. You are now in programming mode. Follow the chart below for programming options. User Option Button Sequence Options Ⅰ Ⅱ Ⅲ Remote Start Run Time Ⅳ→Ⅰ 15 min 5 min 25 min Diesel Warm Up Time Ⅳ→Ⅱ 30 sec 15 sec 7.
3.12 Time, Alarm, Remote Start Timer Set ButtonⅡ4 sec The time, alarm, and remote start timer can be set by holding down Button I for 4 seconds. The following buttons are used. ButtonⅠ : Time Menu (Time → Alarm→ Remote Start Timer) Press and hold Button Ⅱ for 4 seconds. Once the time starts to blink, toggle to Alarm and Remote Start Time and back to Time by pressing Button I for 0.5 second at a time. ButtonⅡ : Hours setting. Press and/or hold Button II in order to increase the hours value.
3.13 Aux 1 Output Buttons Ⅰ + Ⅱ 0.5 sec Aux 1 output can be used to control other devices such as window modules for rolling up or rolling down windows. Press Buttons Ⅲ + Ⅳ for 0.5 second to activate Aux 1 output. 2 parking light flashes and 2 siren chirps will confirm output. The remote control will blink 2 times and beep 2 times. 3.14 Aux 2 Output Buttons Ⅲ+ Ⅳ 0.5 sec Aux 2 output can be used to control other devices such as window modules for rolling up or rolling down windows. Press Buttons Ⅱ+ Ⅳ for 0.
3.16 Shock Sensor Sensitivity Adjustment The sensitivity of the shock sensor can be controlled by turning a dial on the shock sensor module. Turn the dial according to the amount of sensitivity that is desired. Keep in mind that turning the sensitivity to its maximum can result in false alarms Remote Control Vehicle Full Shock Tune Continuous parking light flash and siren sound. Warning Shock Beep 10 second parking light flash and siren sound. 3.
4. Triggers The following triggers will occur ONLY when the system is armed. Shock Trigger Remote Control Vehicle & will blink. The remote control will beep or vibrate. Parking lights will flash and siren will sound. Door Trigger Remote Control Vehicle & will blink. The remote control will beep or vibrate. Parking lights will flash and siren will sound. Hood Trigger Remote Control Vehicle & will blink. The remote control will beep or vibrate. Parking lights will flash and siren will sound.
WARRANTY CARD Use this warranty card for your records. Please go to www.zenesisalarms.com Visit the link above for specific warranty terms and conditions. ITU emission Code 8K50F1D Oscillation Type X-TAL Modulation Type FSK (Frequency shift keying) Data Rate (Mbps) 1200 bps Operated Frequency 433.