Page 1 Appendix A – Notices The Veri-Series product line has been tested for compliance with all applicable international standards. The resulting approvals are listed below, and are additionally printed on the labeling located on the rear panel of the product. The power supply offered by Bioscrypt is CE and CSA approved and UL listed.
Page 2 • Increase the separation between the equipment and receiver • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected • Consult the dealer or an experienced radio/TV technician for help CE Information to Users All Veri-Series devices have the CE mark, for compliance with CISPR22 /EN 55022 requirements.
Page 3 If the filters were not included with the product or if they are desired separately, they may be ordered from Bioscrypt (part number 832-00103-00) or the distributor from which the product was purchased. Please see Appendix C for details on proper installation of these filters. NOTE: The installation of these filters is mandatory for the registered CE mark, and associated R&TTE directive compliance to be valid within the European Union.
Page 4 V-Station, A, G Information for Users The V-Station, A, G includes a contact-less smart card reader (GemEasyLink680SL). This is a radio-transceiver with the following characteristics: Operating Frequency Range: RF Power Rating: RF Output Impedance: 13.553-13.567 MHz 0.0 Watts 50 Ohms V-Station, A, H Information for Users The V-Station, A, H includes a contact-less smart card reader (HID iCLASS™ OEM 100/RS232).
Page 5 Appendix B – European Certification Documentation This appendix contains data related to the Veri-Series product line regarding the test procedures and Declarations of Conformity as required under the R&TTE directive by the European Union for all devices containing radio transmitters.
Page 6 DECLARATION OF CONFORMITY FOR THE R&TTE DIRECTIVE 1999/5/EC Manufacturer’s Name/Address: Address: Contact Person: Bioscrypt Inc. 505 Cochrane Drive Markham Ontario Canada, L3R 8E3 Mr. Shiraz Kapadia, Vice President of Operations Phone #: 905-940-7784 Fax #: 905-940-7642 Email Address: shiraz.kapadia@bioscrypt.com Equipment Type: Radio Communications Equipment Product Name: V-Prox, A Model No.: V-Prox, A, H RF Output Power: -6.
Page 7 DECLARATION OF CONFORMITY FOR THE EMC DIRECTIVE 89/336/EEC Manufacturer’s Name/Address: Address: Contact Person: Bioscrypt Inc. 505 Cochrane Drive Markham Ontario Canada, L3R 8E3 Mr. Shiraz Kapadia, Vice President of Operations Phone #: 905-940-7784 Fax #: 905-940-7642 Email Address: shiraz.kapadia@bioscrypt.com Equipment Type: Radio Communications Equipment Product Name: V-Prox, A Model No.: V-Prox, A, H RF Output Power: -6.
Page 8 DECLARATION OF CONFORMITY FOR THE LOW VOLTAGE SAFETY DIRECTIVE 73/23/EEC Manufacturer’s Name/Address: Address: Contact Person: Bioscrypt Inc. 505 Cochrane Drive Markham Ontario Canada, L3R 8E3 Mr. Shiraz Kapadia, Vice President of Operations Phone #: 905-940-7784 Fax #: 905-940-7642 Email Address: shiraz.kapadia@bioscrypt.com Equipment Type: Radio Communications Equipment Product Name: V-Prox, A Model No.: V-Prox, A, H RF Output Power: -6.
Page 9 DECLARATION OF CONFORMITY FOR THE R&TTE DIRECTIVE 1999/5/EC Manufacturer’s Name/Address: Address: Contact Person: Bioscrypt Inc. 505 Cochrane Drive Markham Ontario Canada, L3R 8E3 Mr. Shiraz Kapadia, Vice President of Operations Phone #: 905-940-7784 Fax #: 905-940-7642 Email Address: shiraz.kapadia@bioscrypt.com Equipment Type: Radio Communications Equipment Product Name: V-Smart Model No.: V-Smart, A RF Output Power: -19.
Page 10 DECLARATION OF CONFORMITY FOR THE EMC DIRECTIVE 89/336/EEC Manufacturer’s Name/Address: Address: Contact Person: Bioscrypt Inc. 505 Cochrane Drive Markham Ontario Canada, L3R 8E3 Mr. Shiraz Kapadia, Vice President of Operations Phone #: 905-940-7784 Fax #: 905-940-7642 Email Address: shiraz.kapadia@bioscrypt.com Equipment Type: Radio Communications Equipment Product Name: V-Smart Model No.: V-Smart, A RF Output Power: -19.
Page 11 DECLARATION OF CONFORMITY FOR THE LOW VOLTAGE SAFETY DIRECTIVE 73/23/EEC Manufacturer’s Name/Address: Address: Contact Person: Bioscrypt Inc. 505 Cochrane Drive Markham Ontario Canada, L3R 8E3 Mr. Shiraz Kapadia, Vice President of Operations Phone #: 905-940-7784 Fax #: 905-940-7642 Email Address: shiraz.kapadia@bioscrypt.com Equipment Type: Radio Communications Equipment Product Name: V-Smart Model No.: V-Smart, A RF Output Power: -19.
Page 12 DECLARATION OF CONFORMITY FOR THE R&TTE DIRECTIVE 1999/5/EC Manufacturer’s Name/Address: Address: Contact Person: Bioscrypt Inc. 505 Cochrane Drive Markham Ontario Canada, L3R 8E3 Mr. Shiraz Kapadia, Vice President of Operations Phone #: 905-940-7784 Fax #: 905-940-7642 Email Address: shiraz.kapadia@bioscrypt.com Equipment Type: Radio Communications Equipment Product Name: V-Smart Model No.: V-Smart, A, H RF Output Power: 4.
Page 13 DECLARATION OF CONFORMITY FOR THE EMC DIRECTIVE 89/336/EEC Manufacturer’s Name/Address: Address: Contact Person: Bioscrypt Inc. 505 Cochrane Drive Markham Ontario Canada, L3R 8E3 Mr. Shiraz Kapadia, Vice President of Operations Phone #: 905-940-7784 Fax #: 905-940-7642 Email Address: shiraz.kapadia@bioscrypt.com Equipment Type: Radio Communications Equipment Product Name: V-Smart Model No.: V-Smart, A, H RF Output Power: 4.
Page 14 DECLARATION OF CONFORMITY FOR THE LOW VOLTAGE SAFETY DIRECTIVE 73/23/EEC Manufacturer’s Name/Address: Address: Contact Person: Bioscrypt Inc. 505 Cochrane Drive Markham Ontario Canada, L3R 8E3 Mr. Shiraz Kapadia, Vice President of Operations Phone #: 905-940-7784 Fax #: 905-940-7642 Email Address: shiraz.kapadia@bioscrypt.com Equipment Type: Radio Communications Equipment Product Name: V-Smart Model No.: V-Smart, A, H RF Output Power: 4.
Page 15 DECLARATION OF CONFORMITY FOR THE R&TTE DIRECTIVE 1999/5/EC Manufacturer’s Name/Address: Address: Contact Person: Bioscrypt Inc. 505 Cochrane Drive Markham Ontario Canada, L3R 8E3 Mr. Shiraz Kapadia, Vice President of Operations Phone #: 905-940-7784 Fax #: 905-940-7642 Email Address: shiraz.kapadia@bioscrypt.com Equipment Type: Radio Communications Equipment Product Name: V-Station Model No.: V-Station, A, P RF Output Power: 3.
Page 16 DECLARATION OF CONFORMITY FOR THE EMC DIRECTIVE 89/336/EEC Manufacturer’s Name/Address: Address: Contact Person: Bioscrypt Inc. 505 Cochrane Drive Markham Ontario Canada, L3R 8E3 Mr. Shiraz Kapadia, Vice President of Operations Phone #: 905-940-7784 Fax #: 905-940-7642 Email Address: shiraz.kapadia@bioscrypt.com Equipment Type: Radio Communications Equipment Product Name: V-Station Model No.: V-Station, A, P RF Output Power: 3.
Page 17 DECLARATION OF CONFORMITY FOR THE LOW VOLTAGE SAFETY DIRECTIVE 73/23/EEC Manufacturer’s Name/Address: Address: Contact Person: Bioscrypt Inc. 505 Cochrane Drive Markham Ontario Canada, L3R 8E3 Mr. Shiraz Kapadia, Vice President of Operations Phone #: 905-940-7784 Fax #: 905-940-7642 Email Address: shiraz.kapadia@bioscrypt.com Equipment Type: Radio Communications Equipment Product Name: V-Station Model No.: V-Station, A, P RF Output Power: 3.
Page 18 DECLARATION OF CONFORMITY FOR THE R&TTE DIRECTIVE 1999/5/EC Manufacturer’s Name/Address: Address: Contact Person: Bioscrypt Inc. 505 Cochrane Drive Markham Ontario Canada, L3R 8E3 Mr. Shiraz Kapadia, Vice President of Operations Phone #: 905-940-7784 Fax #: 905-940-7642 Email Address: shiraz.kapadia@bioscrypt.com Equipment Type: Radio Communications Equipment Product Name: V-Station Model No.: V-Station, A,G RF Output Power: -10.
Page 19 DECLARATION OF CONFORMITY FOR THE EMC DIRECTIVE 89/336/EEC Manufacturer’s Name/Address: Address: Contact Person: Bioscrypt Inc. 505 Cochrane Drive Markham Ontario Canada, L3R 8E3 Mr. Shiraz Kapadia, Vice President of Operations Phone #: 905-940-7784 Fax #: 905-940-7642 Email Address: shiraz.kapadia@bioscrypt.com Equipment Type: Radio Communications Equipment Product Name: V-Station Model No.: V-Station, A, G RF Output Power: -10.
Page 20 DECLARATION OF CONFORMITY FOR THE LOW VOLTAGE SAFETY DIRECTIVE 73/23/EEC Manufacturer’s Name/Address: Address: Contact Person: Bioscrypt Inc. 505 Cochrane Drive Markham Ontario Canada, L3R 8E3 Mr. Shiraz Kapadia, Vice President of Operations Phone #: 905-940-7784 Fax #: 905-940-7642 Email Address: shiraz.kapadia@bioscrypt.com Equipment Type: Radio Communications Equipment Product Name: V-Station Model No.: V-Station, A, G RF Output Power: -10.
Page 21 DECLARATION OF CONFORMITY FOR THE R&TTE DIRECTIVE 1999/5/EC Manufacturer’s Name/Address: Address: Contact Person: Bioscrypt Inc. 505 Cochrane Drive Markham Ontario Canada, L3R 8E3 Mr. Shiraz Kapadia, Vice President of Operations Phone #: 905-940-7784 Fax #: 905-940-7642 Email Address: shiraz.kapadia@bioscrypt.com Equipment Type: Radio Communications Equipment Product Name: V-Station Model No.: V-Station, A, H RF Output Power: -6.
Page 22 DECLARATION OF CONFORMITY FOR THE EMC DIRECTIVE 89/336/EEC Manufacturer’s Name/Address: Address: Contact Person: Bioscrypt Inc. 505 Cochrane Drive Markham Ontario Canada, L3R 8E3 Mr. Shiraz Kapadia, Vice President of Operations Phone #: 905-940-7784 Fax #: 905-940-7642 Email Address: shiraz.kapadia@bioscrypt.com Equipment Type: Radio Communications Equipment Product Name: V-Station Model No.: V-Station, A, H RF Output Power: -6.
Page 23 DECLARATION OF CONFORMITY FOR THE LOW VOLTAGE SAFETY DIRECTIVE 73/23/EEC Manufacturer’s Name/Address: Address: Contact Person: Bioscrypt Inc. 505 Cochrane Drive Markham Ontario Canada, L3R 8E3 Mr. Shiraz Kapadia, Vice President of Operations Phone #: 905-940-7784 Fax #: 905-940-7642 Email Address: shiraz.kapadia@bioscrypt.com Equipment Type: Radio Communications Equipment Product Name: V-Station Model No.: V-Station, A, H RF Output Power: -6.
Page 24 Appendix C – Installing the R&TTE Installation Kit Filters The following two sections describe the proper procedures for installing the R&TTE Installation Kit filters, which are required in certain European countries for full CE compliance. These kits are required only for the V-Prox and V-Smart products and are not required for any other Bioscrypt product. More information can be found regarding the CE R&TTE directive online at the European Union web site: http://www.europa.eu.
Page 25 Figure 16: V-Prox R&TTE Installation Kit Wiring Diagram R&TTE Wiring Instructions for the V-Smart, A and V-Smart, A, H In order to comply with the conducted emissions requirements of the European Community directive EN 55022 for DC power input/output ports, an additional line filter is needed for installations where power supply cables are greater than 3 meters in length. The required filter is manufactured by JMK Filters (Amhearst, New Hampshire, USA), Part No.
Page 26 through the aperture until the wall plate is between the two mounting flanges of the filter. The device may now be rotated back 90 degrees to the upright position and lowered onto the mounting hooks of the wall plate. Please see figure 17 for wiring details. Figure 17: V-Smart R&TTE Installation Kit Wiring Diagram Document #430-90003-16 © Copyright 2005 Bioscrypt Inc. All Rights Reserved.
Page 27 References (1) B & B Electronics offers an Application Note on RS-485 devices, system configuration, and termination. B & B Electronics 707 Dayton Road P.O. Box 1040 Ottawa, IL 61350 (815)433-5100 http://www.bb-elec.com (2) Robust Data Comm provides services and a vast amount of information at their WWW site. Robust Data Comm, Inc. St. Paul, MN 55112 (612)628-0533 http://www.robustdc.
Page 28 (6) Alpha Wire Company offers a variety of cables suitable for RS-485 use and has a number of technical papers: http://www.alphawire.com (7) Cisco Systems, Inc., provides a comprehensive guide to Ethernet 802.x standards and implementation issues: http://www.cisco.com/univercd/cc/td/doc/cisintwk/ito_doc/ethernet.htm (8) Charles Spurgeon provides an excellent online Ethernet resource: http://www.ethermanage.com/ethernet/ethernet.
Page 29 Bioscrypt Contact Information Technical Support Contact Information: Telephone: 866.304.7180 (toll free) 818.304.7180 (direct) Fax: 818.304.7187 Email: Web: support@bioscrypt.com http://www.bioscrypt.com Hours: 5:30A – 5:00P PST (Monday – Friday) Address: Bioscrypt Inc Technical Support Dept 5805 Sepulveda Blvd, Suite 750 Van Nuys, CA, 91411 Corporate & Canadian Office 505 Cochrane Dr. Markham, ON, Canada L3R 8E3 T 905 940 7750 F 905 940 7642 www.bioscrypt.com Document #430-90003-16 U.S.
Veri-Series Setup Guide Checklist For Unpacking Veri-Series reader (V-Smart and V-Station differ from picture shown) Wall mounting plate / Mullion mounting plate Tools 1/8” security hex key (V-Smart and V-Station differ from picture shown ) Pigtail cable (not included for V-Station) Documentation Veri-Series Setup Guide Hardware (4) #6-32 screws (4) #6 self-tapping screws (4) #4-8 wall anchors (14) crimps (1) plastic Aux port door (2) #4-40 screws Documentation provided with your new fingerprint read
Veri-Series Setup Guide Other required equipment PC (optional for V-Station) One available COM port (or Ethernet card) Windows 98, ME, NT4, 2000, or XP 486-compatible 16 MB RAM 30 MB disk space Power supply Door controller Networking cable RS-232/RS-485 Converter P/S for converter CD with VeriAdmin software and documentation User Documentation (included on VeriAdmin CD) © Copyright 2005 Bioscrypt Inc. All rights reserved.
Veri-Series Setup Guide Introduction The Veri-Series Setup Guide provides you with general information on installing your fingerprint reader and using the reader and associated software. This document is not a substitute for the more comprehensive documentation provided with your reader and available on the CD-ROM or installed on your computer with the VeriAdmin software. Please refer to the Veri-Series Installation Guide and the Veri-Series Operations Manual for additional information.
Veri-Series Setup Guide Learning More About Your New Fingerprint Reader Pass/Fail Indicator Amber – place finger Off – remove finger Green – Pass Red – Fail Conductive Plastic Mask Power Indicator RidgeLock™ to aid in consistent finger placement Fingerprint Sensor ABS Plastic Body Aux. Port Internally, your fingerprint reader is powered by hardware and software developed by Bioscrypt. The “bioscrypt on board™” logo signifies that Bioscrypt's biometric technology has been integrated into this product.
Veri-Series Setup Guide The V-Smart™ Fingerprint Reader Pass/Fail Indicator Amber – place finger Off – remove finger Green – Pass Red – Fail Conductive Plastic Mask Fingerprint Sensor RidgeLock™ to aid in consistent finger placement Power Indicator MIFARE® or iCLASS™ smart card reader ABS Plastic Body Aux. Port © Copyright 2005 Bioscrypt Inc. All rights reserved.
Veri-Series Setup Guide The V-Station™ Fingerprint Reader Pass/Fail Indicator Conductive Plastic Amber – place finger Off – remove finger Green – Pass Red – Fail Fingerprint Sensor LCD Backlit Display RidgeLock™ Power Indicator Illuminated Keypad Some models: MIFARE® or iCLASS™ smart card reader or HID Proximity reader Aux. Port ABS Plastic Body © Copyright 2005 Bioscrypt Inc. All rights reserved.
Veri-Series Setup Guide The Veri-Series Product Line The Veri-Series fingerprint readers are used in access control and other related fields. There are a variety of features common to the various products, but there are differences as well, as described below. For more on the operational differences between the products please see Basic Operation on page 29.
Veri-Series Setup Guide system. The V-Pass is also small enough to be mounted on a door mullion or a single-gang electrical box. V-Smart™: The V-Smart supports one-to-one fingerprint authentication by means of an industry standard MIFARE®-compatible or iCLASS™ contactless smart card reader. The fingerprint template is stored on the smart card, not on the reader, so the user population is unlimited – simply issue a smart card to each employee.
Veri-Series Setup Guide Required Connections The following table shows required and optional connections to the various products. Product V-Prox Wiegand Output *** Serial Comm. ** V-Flex *** ** V-Pass *** V-Smart V-Station Power Input * * Wiegand Input Earth Ground *** *** ** * The power input on V-Smart is 9-12 VDC and 12.5-24VDC on V-Station instead of 9-24 VDC on the other products. ** RS-485 communication is typically used for template distribution to multiple units.
Veri-Series Setup Guide Preparing Wiring 1. Wiring connections to be made: Wiegand – should be 18-22 AWG (10-7 MWG) wire, between 3 and 6 conductors depending on which signals will be carried, shielded cable is recommended, and typically the conductors are made of stranded wire. Minimum connections: Data0, Data1, Wiegand Ground RS-485 – use category 5 shielded cable. Ethernet – use category 5 shielded cable Power – should be 18 – 22 AWG (10 – 7 MWG) wire, 2 conductors.
Veri-Series Setup Guide 2.
Veri-Series Setup Guide 3. Weidmuller Connections (V-Station only): Group Label RS-485 RS-232 Power/Ground Wiegand TTL (IN) TTL (OUT) TX(+) TX(-) RX(+) RX(-) GND GND TX RX +(POS) -(NEG) EGND IN 0 IN 1 OUT 0 OUT 1 LED IN LED OUT GND IN 0 IN 1 OUT 0 H OUT 1 L GND Signal Description Transmit + Transmit Receive + Receive RS-485 Ground RS-232 Ground Transmit Receive 12.5 - 24 VDC + 12.
Veri-Series Setup Guide Power Supply 2 Unit Door Controller 3 Unit Unit Unit Cat5 Twisted Pair Data0 Data1 Wiegand Gnd. RS-232 /RS-485 Converter Computer Use one pair (e.g. blue/white and white/blue) for RS-485 connections. Connect readers identically at each reader (e.g. blue/white on Cat5 to RS485 (-) on pigtail/Weidmuller Connector and white/blue on Cat5 to RS-485 (+) on pigtail/Weidmuller Connector). 5. [RS-485 network only]: At converter, jumper TD(A) with RD(A) and TD(B) with RD(B).
Veri-Series Setup Guide 8. [Ethernet network only]: Typically a star network topology is used with a network switch or hub, but a bus topology may be used. Be sure to connect all devices using straight-thru (as apposed to cross-over) cables. The exception to this is when connecting a single device directly to the computer Ethernet adaptor. 9. [Ethernet network only]: Up to 254 readers can reside on a single Ethernet bus, although repeaters may be required to boost the signal over longer distances.
Veri-Series Setup Guide Configuring Readers See Page 11 for Color Codes +12 VDC Pigtail OR Weidmuller Ground Wiegand Out Data0 Wiegand Out Data1 Wiegand Ground To Computer Power Supply Door Controller Data 0 Data 1 Common Earth Ground 1. Set up a configuration station a. Wire the unit for power: • V-Prox/V-Flex/V-Pass: Connect the RED pigtail wire to 9-24V DC power and the BLACK wire to power ground. • V-Smart: Connect the RED pigtail wire to 9-12V DC power and the BLACK wire to power ground.
Veri-Series Setup Guide 3. Configure the device using the VeriAdmin software provided a. If running VeriAdmin for the first time, you will be directed to the Network Setup dialog. This dialog is also reached by clicking on this icon: . Select the serial (COM) port(s) you intend to use or Ethernet and click OK. It is recommended that you check “Auto”. © Copyright 2005 Bioscrypt Inc. All rights reserved.
Veri-Series Setup Guide b. This will bring you to the Network Configuration Manager dialog. First click on the Comm port or Ethernet within the network tree which you have connected the unit to (the or icon). Then click on the “Add Unit” button (lower left). © Copyright 2005 Bioscrypt Inc. All rights reserved.
Veri-Series Setup Guide c. VeriAdmin should establish communication with the unit. The Unit Status field should indicate ONLINE, you may hear the unit beep, and other fields on the right side should populate. If you are connecting via Ethernet, you must first assign the unit an IP address from the unit’s keypad and then type in the address under Ethernet Settings and click the Refresh button. d. If VeriAdmin shows NOT RESPONDING, check the connections and then press the Refresh button to try again. e.
Veri-Series Setup Guide g. Change desired parameters. Typical changes are: i. Communication Tab: Network ID (default is 0, but each unit must have a unique ID number such as 1, 2, 3, 4, etc.) ii. Wiegand Tab: Wiegand parameters NOTE: We do not recommend changing the Aux. port Baud rate at this time. 4. Repeat steps 2-4 (skipping 3a) for the next reader until all readers are configured. © Copyright 2005 Bioscrypt Inc. All rights reserved.
Veri-Series Setup Guide 5. If placing units on a RS-485 network, you will also need to set up the computer for RS-485 communications. a. Connect the RS-232/RS-485 converter to the PC’s COM port (must support Send Data – a means of automatically sensing data sent from the RS-232 port – we suggest the B&B Electronics, www.bbelec.com, model 485TBLED or equivalent). b. Run category 5 rated cable from the converter to the first reader in the daisy chain. 6. V-Smart considerations a.
Veri-Series Setup Guide 7. V-Station considerations a. The V-Station does not require configuration via a PC. Nearly all configuration options can be set using the menus on the unit. However, it may be more convenient to administer the device from the PC due to the limited size of the LCD screen. b. To distribute templates to other V-Stations, you will need to place all V-Stations on a network and administer them via the PC.
Veri-Series Setup Guide Mounting Readers On The Wall 1. The readers come disassembled, however, if your reader has previously been assembled then disassemble the reader body and smart card module (for VSmart only) from the wall plate. a. On V-Smart remove security screw securing smart card module b. For products other than V-Station, remove security screw securing the Aux. port cover, and remove the Aux. port cover by twisting (see graphics on page 25). c.
Veri-Series Setup Guide 3. 4. 5. 6. less than 2 ½ inches tall if mounting into dry wall so that there is enough material to hold the anchor. The recommended size is 3 ½ inches wide by 2 ½ inches tall. f. For V-Station, the rear of the unit will protrude past the wall plate and into the wall approximately 1 inch (depending on the Weidmuller connectors attached). The access hole must be exactly the size of the hole in the wall plate (136mm (~5 3/8”) wide by 69mm (~2 ¾”) tall).
Veri-Series Setup Guide 7. Attach pigtail to the reader body (not applicable to V-Station) and attach body to wall plate using same motion as for the smart card module. Secure the body to the wall plate with the #4-40 screw at the bottom. Replace the Aux. port cover (see next page). 8. The RJ11 security cover is removed to install the reader body to the wall mount.
Veri-Series Setup Guide 4) Finally, fold the cover up and secure it using the supplied security screw and special Allen wrench. The following pages show the dimensions of the wall mounting plates for the smaller Veri-Series readers (V-Prox, V-Flex, V-Pass), the V-Smart, and the VStation. The diagrams are not to scale however full-scale drawings can be found in the Veri-Series Installation Guide. © Copyright 2005 Bioscrypt Inc. All rights reserved.
Veri-Series Setup Guide 2 ¾” (70 mm) 1 1/8” (28 5 5/16” (135 mm) 5/32” ø 1 ¼” (32 mm) 1 1/8” (28 mm) 11/16” (17 mm) 3 ¼” (82 mm) 1” (25 2 5/8” (67 mm) Mounting Template for V-Prox / V-Flex / V-Pass (not to scale) © Copyright 2005 Bioscrypt Inc. All rights reserved.
Veri-Series Setup Guide Mounting Template for V-Smart (MIFARE and iCLASS) (not to scale) © Copyright 2005 Bioscrypt Inc. All rights reserved.
Veri-Series Setup Guide Mounting template for V-Station (all models) (not to scale) © Copyright 2005 Bioscrypt Inc. All rights reserved.
Veri-Series Setup Guide Basic Operation 1. Use VeriAdmin software to enroll a new fingerprint: Enrollment is the process of generating data that the reader will store and use to later verify your identity. a. Make sure that the correct unit is identified on the main toolbar dropdown. b. Go to the Template Manager screen. c. Click on Quick Enroll. d. Enter an ID number.
Veri-Series Setup Guide g. Fill in desired information and decide where the template will be stored (either on PC, the unit used to enroll, or a smart card). Click on the appropriate “Save” button. h. If templates are saved to the PC or the unit and are to be distributed to other readers, then this can be done using the Template Manager functions. In the case of V-Smart, the template is stored on the smart card and does not need to be distributed. © Copyright 2005 Bioscrypt Inc. All rights reserved.
Veri-Series Setup Guide 2. Using the keypad to enroll a new fingerprint (V-Station only): a. From the idle screen (showing ”Bioscrypt” with the date and time), press 0-0-0 (three zeroes) and . You will be warned about no admin ID. b. You are now in the V-Station menu system. From here you may traverse the menus using the c. d. e. f. and buttons, the button to enter a menu, and the button to back out to the previous menu. Enter the Template Admin menu, then the Enroll (Add) User menu.
Veri-Series Setup Guide or to a smart card (2). If saving to a smart card, you will need to enter the current site key (it must be numeric, and is set using VeriAdmin) and then present an appropriate fresh or blank smart card. l. Finally, you may elect to enroll an alternate finger with the same ID. Press 1 for yes or 2 for no 3. Verification is as simple as: Verification is the process of comparing a live fingerprint scan to the fingerprint data stored during enrollment. a.
Veri-Series Setup Guide performance of the system. Cleaning can be done regularly but is only required when a significant amount of residue builds up on the sensor. To clean the sensor, use a clean, soft cloth dipped in isopropyl (rubbing) alcohol. Use a sweeping motion to remove deposits from the sensor. Do not use a soiled cloth or any abrasive brushes, pads or detergents. © Copyright 2005 Bioscrypt Inc. All rights reserved.
Veri-Series Setup Guide Disclaimer The instructions in this document have been carefully checked for accuracy and are presumed to be reliable. Bioscrypt, Inc. and its writers assume no responsibility for inaccuracies and reserve the right to modify and revise this document without notice. It is always our goal at Bioscrypt, Inc. to supply accurate and reliable documentation. If you discover a discrepancy in this document, please e-mail your comments to support@bioscrypt.
Veri-Series Setup Guide Bioscrypt One Year Limited Warranty Policy Bioscrypt warrants to the original consumer purchaser (“Customer”) that new Bioscrypt products will be free from defects in material and workmanship for one year from the date the product was shipped from Bioscrypt. For replacement products the warranty on the replacement unit is the remainder of the warranty on the original product or ninety (90) days, whichever is longer.
Veri-Series Setup Guide • Damage caused during installation • Damage caused by the equipment or system with which the biometric reader is used • Damage caused by modification or repairs not made or authorized by Bioscrypt • Damage caused by improper packaging • Damage caused by lack of ESD protection • Merchandise that is determined to be stolen All Veri-Series units have an operating temperature range of 0°-60° Celsius (32°-140° Fahrenheit).
Veri-Series Setup Guide This warranty is exclusive and in lieu of all others, whether oral or written, expressed or implied. Bioscrypt specifically disclaims any and all implied warranties, including without limitation, warranties of merchantability and fitness for any particular purpose. No Bioscrypt dealer, agent, or employee is authorized to make any modification, extension or addition to this warranty. © Copyright 2005 Bioscrypt Inc. All rights reserved.
Veri-Series Setup Guide Bioscrypt Return Policy and Procedures Bioscrypt must be notified within thirty days of the date that a defect is discovered. Bioscrypt will then issue a Return Material Authorization (RMA) number which the Customer must include with all correspondence and display on the outside of the shipping container when returning the product. Any products returned later than 30 days after issuance of an RMA may be subject to review as to whether the authorization to return is still warranted.
Veri-Series Setup Guide Carefully read the following regarding billable repairs: By shipping product to Bioscrypt using the RMA provided by the Technical Support Department, you are agreeing to the following terms: For all non-warranty repairs or billable repairs, the customer will be responsible for charges associated with parts, labor and shipping/freight to and from the Bioscrypt repair facility.
Veri-Series Setup Guide 30 Day Return for Credit Bioscrypt is a leading biometric company, specializing in fingerprint and verification systems. We are confident that customers will be pleased with Bioscrypt products.
Veri-Series Setup Guide Notices The Veri-Series line of products has been tested for compliance with all applicable international standards. The resulting approvals are listed below, and are additionally printed on the labeling located on the rear panel of the product. The power supply offered by Bioscrypt is CE and CSA approved and UL listed.
Veri-Series Setup Guide Technical Support Contact Information: Telephone: 866.304.7180 (toll free) 818.304.7180 Fax: 818.304.7187 Email: Web: support@bioscrypt.com http://www.bioscrypt.com Hours: 5:30A – 5:00P PST (Monday – Friday) Address Bioscrypt Inc. Technical Support Department 5805 Sepulveda Blvd., Suite 750 Van Nuys, CA 91411 © Copyright 2005 Bioscrypt Inc. All rights reserved.
Veri-Series Setup Guide For your records Model: Serial Numbers: Installer/Reseller: Installation Date: Notes: Corporate & Canadian Office 505 Cochrane Dr. Markham, ON, Canada L3R 8E3 T 905 940 7750 F 905 940 7642 www.bioscrypt.com U.S. Office 5805 Sepulveda Blvd., Suite 750 Van Nuys, CA 91411 T 818 304 7150 F 818 461-0843 © Copyright 2005 Bioscrypt Inc. All rights reserved. Document #430-00111-18 U.K.