SLIM ONE OWNER’S MANUAL
TABLE OF CONTENTS PRODUCT INFORMATION Safety Precautions..................................................4 Parts...............................................................................8 Product.........................................................................9 Dimensions.................................................................10 Remote Control.........................................................11 INSTALLATION Installation.........................................................
SAFETY PRECAUTIONS IMPORTANT SAFEGUARDS • When using electrical products, especially when children are present, basic safety precautions should always be followed. READ ALL INSTRUCTIONS BEFORE USING • For use with 120V 60Hz: Power supply must be a 15 Amp GFCI outlet. WARNING - TO REDUCE THE RISK OF BURNS, ELECTROCUTION OR INJURY TO PERSONS: • Close supervision is necessary when this product is use by, on, or near children. • Use this product only for its intended use as described in this manual.
SAFETY PRECAUTIONS (CONT.) GROUNDING INSTRUCTION DANGER- Improper use of the grounding plug can result in a risk of electric shock. This product has a three-prong grounding plug, which must be plugged into an outlet that is properly installed and grounded. In the event of an electrical short circuit, grounding reduces the risk of shock by providing an escape wire for the electrical current.
PARTS PRODUCT Water supply hose 8 9
DIMENSIONS REMOTE CONTROL Elongated type BIDETT To run the bidet function. (1 minute) PULSE TTURBO To run the turbo function. (1 minute) To control the nozzle position. SEAT TEMP To run the pulse function during wash/bidet/ turbo operation. STOP 18.5(470) 15.9(406) 8.1(206) 4.7(120)~8.3(210) To stop any operations.
INSTALLATION 1. Remove the seat from the existing toilet body. 2. Install the T-Valve. 5. Connect bidet hose. 6. Turn on the water Installation of T-valve Removal of water hose • Release the nuts, and then remove the seat and cover. • Store the seat in a proper place for future use. • Turn off the water. 3. Fix the catch plate onto the toilet. • Remove the existing water hose and then install T-valve to the bottom of the toilet tank.
HOW TO USE 1. Sit On The Toilet Seat 2. Wash, Bidet, Turbo 3. Pulse 4. Child Function Seat sensor • Be sure to sit on the seat sensor. If the sensor is not occupied, all functions will not operate. • Skin to seat contact needs to occur to activate seat. • Selected function can be used as described. • When pressing the selected function again, the nozzle will oscillate back and forth to wash a wider range.
HOW TO USE (CONT.) 5. Nozzle Position Control • Nozzle position is adjustable (5 levels). 6. Water Pressure Control • Water pressure is adjustable. (5 levels) • If the water or screen filters become blocked, it may cause low water pressure. Regularly check the water and screens filters. 7. Stop • All operations will stop. • When pressing the stop button for 3 seconds, unit will turn off. • Press Stop, Wash, Bidet, or Turbo to turn on. 8. Seat Temperature Control • Seat temperature is adjustable.
HOW TO USE (CONT.) 9. Energy Saving Function • Eco 1 - This mode will be activated by pressing the Energy Saving button until the yellow LED light turns on. (Seat and water temperature will be kept at 32°C) 10. Nozzle Cleaning • When selecting Nozzle Cleaning while not seated, the nozzle cleans itself 3 times. Then nozzle extends and stop for manual cleaning process. • Eco 2 - This mode will be activated by pressing the Energy Saving button until the green LED light turns on.
HOW TO USE (CONT.) 13. Sitz Bath 14.Seat Sensor Bypass • Wash or Bidet is switched to Wash Sitz Bath or Bidet Sitz Bath if Nozzle Cleaning button is pressed during use. • The seat sensor can be activated and deactivated by pressing Massage button for 3 seconds. • Water pressure is switched to 1st level regardless of preset water pressure settings and Sitz Bath operates for 5 minutes.
MAINTENANCE & CLEANING Screen Filter Cleaning Extended Non-Use Cleaning the Unit Draining of Remaining Water Screen filter Water supply hose 1. Close the water valve. 2. Disconnect the water supply hose. Take the screen filter out and clean it with a soft brush. 3. Return the filter after cleaning and reconnect the water supply hose. 4. Open the water valve. • When bidet seat is not used for an extended period of time, unplug and drain the unit. 1.
SETTINGS TROUBLESHOOTING USER SETTING WITH THE REMOTE CONTROL PLEASE CHECK THE FOLLOWING POINTS BEFORE REQUESTING REPAIR SERVICE. Seat sensor ‘off’ No. Function Seat sensor ‘on’ Seat Status Regardless of on/off Switch Operation Description Initial Status 1 Silent mode “ ” For longer than 3 seconds To turn on/off the operating chime sound.
SPECIFICATIONS WARRANTY BIO BIDET SLIM ONE Rated voltage 120V, 60Hz Max. Power consumption 870W Bio Bidet warrants its products to be free from manufacturing defects under normal use and service for a period of 1 year from the date of purchase. This warranty is extended only to the original purchaser. Power cord length 1.2 m For full warranty details, visit www.biobidet.com Water feed method Directly connects to water pipe Recommended inlet water pressure 99~106.
Thank You Technical Support/Customer Service 7900 S Route 31 Crystal Lake, IL 60014 T: 845.458.2334 U.S TOLL FREE: 877.339.5214 support@biobidet.com www.biobidet.