Bluetooth Modem Bluetooth 56K Wireless Modem User's Manual Index 1. Introduction 2. Specifications 3. Product Shape 4. Bluetooth Modem Mode 5. 56K Modem Mode file:///C¦/Documents and Settings/Alcee/ 面/ww/Manual.
Bluetooth Modem Appendix A. AT Command ¡@ ¡@ 1. Introduction The Bluetooth 56k wireless modem provide a standard V90 Modem for WAN communication and access to Internet. This device is capable of running a complete Bluetooth software stack and in addition to this there is sufficient memory and processing power to also run the Dial-Up Networking (DUN) and fax Bluetooth software application profiles.
Bluetooth Modem ● ● ● ● ● ● ● ● ● 103 ❍ V.42 LAPM, MNP 2-4, and MNP 10 error correction ❍ V.42 bis and MNP 5 data compression TM enhanced cellular performance ❍ MNP 10EC ❍ V.250 and V.251 commands Fax modem send and receive rates up to 14.4 kbps ❍ V.17, V.29, V.27 ter, and V.21 channel 2 ❍ EIA/TIA 578 Class 1 and T.31 Class 1.0, and EIA/TIA 578 Class 2 commands V.80 synchronous access mode supports host-based communication protocols with H.324 interface Telephony/TAM , V.
Bluetooth Modem 2.4. Environment Operating Ranges ● Operation : 25 ~ 80¢J ● Storage : -5 ~ 90¢J 2.5. Power Consumption ● ● Operation : 0.85w(Avg) 1.14W (Max) Standby : 0.26W 2.6. LED Indication ● ● ● ● ● ● Power LED indicator : Power ON Link LED indicator : Bluetooth Link with Host ACT LED indicator : Bluetooth Data TX/RX OH LED indicator : Modem OFF Hook TX LED indicator : Modem Data TX RX LED indicator : Modem Data RX 2.7.
Bluetooth Modem ¡@ file:///C¦/Documents and Settings/Alcee/ 面/ww/Manual.
Bluetooth Modem ¡@ 1. Power LED indicator 7. Reset Button 2. Link LED indicator 8. Antenna 3. ACT LED indicator 9. RJ-11 Socket 4. OH LED indicator 10. Switch 5. TX LED indicator 11. RS-232 Connector 6. RX LED indicator 12. Power Jack 4. Bluetooth Modem Mode Switch to "BT" side. Connect the telephone line to the RJ-11 socket and plug AC adapter to an power outlet. Please refer your Bluetooth software to operate the Bluetooth modem. ¡@ 5. 56K Modem Mode Switch to "RS-232" side. 5.
Bluetooth Modem 1. Connect the telephone line to the RJ-11 socket and plug AC adapter to an power outlet, then plug RS-232 cable male head to RS-232 connector of Bluetooth 56K Wireless Modem and plug female head to your PC. 2. Make sure your PC is powered on and that you are running the Windows operating system. Then system will recognize the device and display the "Add New Hardware Wizard" dialog box. Please insert the driver CD and then click the "Next" button. 3.
Bluetooth Modem 4. Select "Specify a location" and type "G:\Modem" (where G:\ is the path of your CD-ROM drive) in the location or you can click the "Browse" button to select, then click the "Next" button. file:///C¦/Documents and Settings/Alcee/ 面/ww/Manual.
Bluetooth Modem 5. Click the "Next" button, the driver then installs itself. file:///C¦/Documents and Settings/Alcee/ 面/ww/Manual.
Bluetooth Modem 6. Click the "Finish" button to complete the installation process. 5.2 WindowsME Installation 1. Connect the telephone line to the RJ-11 socket and plug AC adapter to an power outlet, then plug RS-232 cable male head to RS-232 connector of Bluetooth 56K Wireless Modem and plug female head to your PC. 2. Make sure your PC is powered on and that you are running the Windows operating system. Then system will recognize the device and display the "Add New Hardware Wizard" dialog box.
Bluetooth Modem 3. Select "Search for the best driver for your device." then choose "Specify a location" and type "G:\Modem" (where G:\ is the path of your CD-ROM drive) in the location or you can click the "Browse" button to select, then click the "Next" button. file:///C¦/Documents and Settings/Alcee/ 面/ww/Manual.
Bluetooth Modem 4. Click the "Next" button, the driver then installs itself. file:///C¦/Documents and Settings/Alcee/ 面/ww/Manual.
Bluetooth Modem 5. Click the "Finish" button to complete the installation process. 5.3 Windows2000 Installation 1. Connect the telephone line to the RJ-11 socket and plug AC adapter to an power outlet, then plug RS-232 cable male head to RS-232 connector of Bluetooth 56K Wireless Modem and plug female head to your PC. 2. Make sure your PC is powered on and that you are running the Windows operating system. Then system will recognize the device and display the "Found New Hardware Wizard" dialog box.
Bluetooth Modem 2. Select "Install the software automatically (Recommended)", then click the "Next" button. file:///C¦/Documents and Settings/Alcee/ 面/ww/Manual.
Bluetooth Modem 3. Select "Specify a location" then click the "Next" button. file:///C¦/Documents and Settings/Alcee/ 面/ww/Manual.
Bluetooth Modem 4. Type "G:\Modem" (where G:\ is the path of your CD-ROM drive) in the location or you can click the "Browse" button to select, then click the "Next" button. 5. Click the "Next" button, the driver then installs itself. file:///C¦/Documents and Settings/Alcee/ 面/ww/Manual.
Bluetooth Modem 6. Windows will search for and recognize the driver of the device, then display one message. Please click the "Yes" button. Windows will then automatically copy the driver files and related files into the system. file:///C¦/Documents and Settings/Alcee/ 面/ww/Manual.
Bluetooth Modem 7. After copying the driver files, click the "Finish" button to complete the installation process. file:///C¦/Documents and Settings/Alcee/ 面/ww/Manual.
Bluetooth Modem ¡@ ¡@ 5.4 WindowsXP Installation 1. Connect the telephone line to the RJ-11 socket and plug AC adapter to an power outlet, then plug RS-232 cable male head to RS-232 connector of Bluetooth 56K Wireless Modem and plug female head to your PC. 2. Make sure your PC is powered on and that you are running the Windows operating system. Then system will recognize the device and display the "Found New Hardware Wizard" dialog box.
Bluetooth Modem 3. Select "Search for the best driver in these locations." and choose "Include this location in the search:" then type "F:\Modem" in the location. Click the "Next" button. file:///C¦/Documents and Settings/Alcee/ 面/ww/Manual.
Bluetooth Modem 4. Windows will search for and recognize the driver of the device, then display one message. Please click the "Continue Anyway" button. Windows will then automatically copy the driver files and related files into the system. file:///C¦/Documents and Settings/Alcee/ 面/ww/Manual.
Bluetooth Modem 5. After copying the driver files, click the "Finish" button to complete the installation process. file:///C¦/Documents and Settings/Alcee/ 面/ww/Manual.
Bluetooth Modem ¡@ 5.5 SuperVoice software Installation¡@ SuperVoice provides data and voice access via connect to internet that capabilities to Microsoft based operating system. To install SuperVoice for the first time on a system: 1. The program will autorun when you insert the software CD to CD drive of your PC. 2. Follow the directions displayed in the SuperVoice installation program. Specify a path name in which you want SuperVoice to be installed. 3.
Bluetooth Modem Appendix A. AT Command Command Function Default Range Reported by &Vn A/ ** A Bn * B0 Repeat last command none - no Answer none - no Select ITU-T or Bell 1 0-3 yes Selects ITU-T V.22 at 1200 bps and ITU-T ¡@ ¡@ ¡@ V.21 at 300 bps B1 Select Bell 212A at 1200 bps and Bell 103J at 300 bps ¡@ ¡@ ¡@ B2 Selects ITU-T V.23 only.
Bluetooth Modem C1 Normal transmit carrier ¡@ ¡@ ¡@ D Dial command none - no Command mode echo 1 0,1 yes E0 Disable echo ¡@ ¡@ ¡@ E1 Enable echo ¡@ ¡@ ¡@ Fn Online echo 1 0,1 no F0 Enables online echo ¡@ ¡@ ¡@ F1 Disables online echo ¡@ ¡@ ¡@ Hn Switch hook control 0 0,1 no H0 Hangs up the telephone line ¡@ ¡@ ¡@ H1 Picks up the telephone line ¡@ ¡@ ¡@ In Identification/checksum option 0 0-14, no En * 20-24 I0 Reports product code file:///C¦/Do
Bluetooth Modem I1 Reports modem chip firmware version ¡@ ¡@ ¡@ I2 Verifies ROM checksum ¡@ ¡@ ¡@ I3 Reports chipset name ¡@ ¡@ ¡@ I4 Reserved ¡@ ¡@ ¡@ I5 Reserved for modem chip hardware configuration ¡@ ¡@ ¡@ I6 Country code ¡@ ¡@ ¡@ I7 Version of board manufacturer firmware ¡@ ¡@ ¡@ I8 Features of modem firmware ¡@ ¡@ ¡@ I10 Modem board configuration-bits set by board manufacturer ¡@ ¡@ ¡@ I11 Modem board configuration-bits set by board manufacturer ¡@ ¡@
Bluetooth Modem I23 Cirrus Logic product model ¡@ ¡@ ¡@ Ln * Speaker volume control 2 0-3 yes L0 Low speaker volume ¡@ ¡@ ¡@ L1 Low speaker volume ¡@ ¡@ ¡@ L2 Medium speaker volume ¡@ ¡@ ¡@ L3 High speaker volume ¡@ ¡@ ¡@ Speaker control 1 0-3 yes M0 Speaker always off ¡@ ¡@ ¡@ M1 Speaker on until carrier present ¡@ ¡@ ¡@ M2 Speaker always on ¡@ ¡@ ¡@ M3 Speaker off during dialing; speaker on until carrier present ¡@ ¡@ ¡@ Nn * Select data rate handsha
Bluetooth Modem On Go online 0 0,1 no O0 Returns modem to data mode ¡@ ¡@ ¡@ O1 Retrains equalizer and then returns to data mode ¡@ ¡@ ¡@ P* Select pulse dialing none - yes Result code display control 0 0,1 yes Q0 Enables result codes ¡@ ¡@ ¡@ Q1 Disables result codes ¡@ ¡@ ¡@ Sn Select an S-register none 0-37 no Write to an S-register none n=0-37 no Qn * Sn=X X=0-255 Sn? Read from an S-register none 0-37 no T* Select tone dialing none - no Vn Result
Bluetooth Modem V1 Choose verbose (text) form ¡@ ¡@ ¡@ Response code data rate 0 0-4 yes W0 Reports DTE speed response codes ¡@ ¡@ ¡@ W1 Reports DTE speed response codes ¡@ ¡@ ¡@ W2 Reports DTE speed response codes ¡@ ¡@ ¡@ W3 Reports DTE speed response codes and information on error correction and data compression ¡@ ¡@ ¡@ W4 Reports protocol, data compression, and DTE data rate ¡@ ¡@ ¡@ Xn * Result code type 4 0-4 yes X0 Enable result codes 0-4; disables detection
Bluetooth Modem Yn * Long space disconnect 0 0,1 yes Y0 Disables long space disconnect ¡@ ¡@ ¡@ Y1 Enables long space disconnect ¡@ ¡@ ¡@ Zn Recall stored profile 0 0,1 no Z0 Resets modem and recalls user profile 0 ¡@ ¡@ ¡@ Z1 Resets modem and recalls user profile 1 ¡@ ¡@ ¡@ DCD (data carrier detect)option 1 0,1 yes &C0 Ignores remote modem status; DCD always on ¡@ ¡@ ¡@ &C1 DCD set according to remote modem status ¡@ ¡@ ¡@ &Dn DTR (data terminal ready) option
Bluetooth Modem &F Load factory defaults none - no Guard tone option (1200 bps and 2400 bps only) 0 0-2 yes &G0 Disables guard tone ¡@ ¡@ ¡@ &G1 Enables 500-Hz guard tone ¡@ ¡@ ¡@ &G2 Enables 1800-Hz guard tone ¡@ ¡@ ¡@ &Jn * Auxiliary relay control 0 0-1 yes &J0 Auxiliary relay never operated ¡@ ¡@ ¡@ &J1 Activates auxiliary relay when modem is offhook ¡@ ¡@ ¡@ &Kn Select serial port flow control 3 0, 3, 4 yes &K0 Disables flow control ¡@ ¡@ ¡@ &K3 Bidirec
Bluetooth Modem &P0 Sets 10-pps pulse dial with 39% / 61% makebreak ¡@ ¡@ ¡@ &P1 Sets 10-pps pulse dial with 33% / 67% makebreak ¡@ ¡@ ¡@ &Q0 * Communication modem option-modem support only async mode 0 0 yes &Sn * DSR (data set ready) option 0 0, 1 yes &S0 DSR is always active ¡@ ¡@ ¡@ &S1 DSR active only during handshaking and when carrier is lost ¡@ ¡@ ¡@ Disable Trellis coding 0 0,1 yes &U0 Enable Trellis coding with QAM as fallback ¡@ ¡@ ¡@ &U1 QAM modulation on
Bluetooth Modem &W0 Store in user profile 0 ¡@ ¡@ ¡@ &W1 Store in user profile 1 ¡@ ¡@ ¡@ &Yn * Select stored profile on power up 0 0, 1 yes &Y0 Recall stored profile 0 on power-up ¡@ ¡@ ¡@ &Y1 Recall stored profile 1 on power-up ¡@ ¡@ ¡@ Store telephone number (up to 30 digits) to location 'n'(0-3) none n=0-3 no &Zn=x x=0-9 A B CD#*T P RW@,!; %En * Auto-retrain control 1 0, 1 yes %E0 Disables auto-retrain ¡@ ¡@ ¡@ %E1 Enables auto-retrain ¡@ ¡@ ¡@ Rate renegot
Bluetooth Modem -Cn * Generate data modem calling tone 1 0-2 yes -Cn Calling tone disabled ¡@ ¡@ ¡@ -C1 1300-Hz calling tone enabled ¡@ ¡@ ¡@ -C2 V.8 calling tone and 1300-Hz calling tone ¡@ ¡@ ¡@ +GMI? Identify modem manufacturer none - no +GMM? Identify product model none - no +GMR? Identify product revision none - no +MS=m Modulation selections V90, 1, 300,0 See note + no + See full command description in the CL-MD56XX Programmer's Guide for parameter ranges.
Bluetooth Modem &An * Set auto-reliable fallback character 13 0-127 yes %Cn * MNP 5 data compression control 1 0,1 yes %C0 No compression ¡@ ¡@ ¡@ %C1 Enables MNP 5 data compression ¡@ ¡@ ¡@ \An * MNP block size 3 0-3 yes \A0 Maximum 64 characters ¡@ ¡@ ¡@ \A1 Maximum 128 characters ¡@ ¡@ ¡@ \A2 Maximum 192 characters ¡@ ¡@ ¡@ \A3 Maximum 256 characters ¡@ ¡@ ¡@ \Bn * Transmit break none 0-9 no \Cn * Set auto-reliable buffer 0 0-2 yes \C0 No data buff
Bluetooth Modem \Gn * Set modem port flow control 0 0, 1 yes \G0 Disables port flow control ¡@ ¡@ ¡@ \G1 Sets port flow control to XON/XOFF ¡@ ¡@ ¡@ \Jn * bps rate adjust control 0 0, 1 yes \J0 Disable rate adjust ¡@ ¡@ ¡@ \J1 Enable rate adjust ¡@ ¡@ ¡@ \Kn * Set break control 5 0-5 yes Enters command mode, no break sent ¡@ ¡@ ¡@ \K1 Destructive/expedited ¡@ ¡@ ¡@ \K3 Nondestructive/expedited ¡@ ¡@ ¡@ \K5 Nondestructive/nonexpedited ¡@ ¡@ ¡@ In connect
Bluetooth Modem \K4, 5 Nondestructive/nonexpedited ¡@ ¡@ ¡@ In connect state, receives break at modem port (if in direct mode): \K0, 2, 4 Immediately sends break and enters command state ¡@ ¡@ ¡@ \K1, 3, 5 Immediately sends the break through ¡@ ¡@ ¡@ In connect state, receives break at modem port and sends to serial port: \K0, 1 Destructive/expedited ¡@ ¡@ ¡@ \K2, 3 Nondestructive/expedited ¡@ ¡@ ¡@ \K4, 5 Nondestructive/nonexpedited ¡@ ¡@ ¡@ \Nn * Set operating mode 3 0-4
Bluetooth Modem \Q0 Disables flow control ¡@ ¡@ ¡@ \Q1 XON/XOFF software flow control ¡@ ¡@ ¡@ \Q2 Unidirectional hardware flow control ¡@ ¡@ ¡@ \Q3 Bidirectional hardware flow control ¡@ ¡@ ¡@ \T0 * Disables inactivity timer 0 0-90 yes Accept reliable link none - no Set XON/XOFF pass-through 0 0, 1 yes \X0 Processes flow control characters ¡@ ¡@ ¡@ \X1 Processes flow control characters and passes to local or remote ¡@ ¡@ ¡@ \Y Switch to reliable mode none - n
Bluetooth Modem "Hn * V.42 bis compression control 3 0-3 yes "H0 Disables V.42 bis ¡@ ¡@ ¡@ "H1 Enables V.42 bis only when transmitting data ¡@ ¡@ ¡@ "H2 Enables V.42 bis only when receiving data ¡@ ¡@ ¡@ "H3 Enables V.42 bis for both transmitting and receiving data ¡@ ¡@ ¡@ "On V.42 bis string length 32 6-250 yes * Value saved in NVRAM The fax modem support four operating modes: buffer (normal), MNP reliable, V.42 auto-reliable, and V.42 reliable.
Bluetooth Modem MNP Reliable MNP 2-5 connection only. If an MNP connection cannot be established, the modem hangs up. \N2 V.42 Auto-Reliable V.42/V.42 bis with fallback to MNP 2-5 or normal mode. \N3 V.42 Reliable V.42, V.42 bit or MNP 2-5 only connection. If a V.42/V.42 bis/MNP 2-5 connection cannot be established, the modem hangs up. \N4 Connection types corresponding to \Nn settings are provided in below.¡@ Resulting \Nn Connection Types \Nn Settings (Answer Modem) ¡@ \Nn Settings \N0 or \N
Bluetooth Modem \N3 Buffer (normal) (V.42 Auto-reliable) mode \N4 Modem hangs up V.42/V.42 bis V.42/V.42 bis V.42/V.42 bis V.42/V.42 bis V.42/V.42bis V.42/V.42 bis (V.42 Reliable) NOTES: 1) MNP 5 requires the modem to be configured for %C1. 2) V.42 bis requires the modem to be configured for "H3. 3) Refer to \Cn and %An commands for more information about auto-reliable mode. The list of command needs to enter a specific error correction or data compression mode are as follow: V.
Bluetooth Modem Fax Identity Commands The fax identity commands are AT+FMFR?, AT+FMDL?, AT+FMI?, AT+FMM?, AT+FMR?, and AT+FREV?. These commands respond back with modem manufacturer, product model, and product revision information.
Bluetooth Modem Command Function Default Range Reported by &Vn +FAE=n Fax/data autorecognition 0 0, 1 no +FCLASS=1 Mode selection 0 0, 1, 8, 80 yes +FRH=n Receive HDLC data none 3 no +FRM=n Receive data none 24, 48, 72, 73, 74, 96, 97, no 98, 121, 122, 145, 146 +FRS=n Wait for silence none 1-255 no +FTH=n Transmit HDLC data none 3 no +FTM=n Transmit data none 24, 48, 72, 73, 74, 96, 97, no 98, 121, 122, 145, 146 +FTS=n Stop transmission and pause none 0-255 no
NOTE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection. This equipment generates, uses and can radiated radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.