3. The router’s (AP’s) SSID and security setting will now be configured to match the SSID and security setting of the registrar. 4. Do Web Page refresh after ER complete AP Configuration to check the new parameters setting.
MAC Filter Select SSID: Select the SSID you want this filter applies to. MAC Restrict Mode: Disable: disable the MAC Filter function. Allow: allow the hosts with the following listed MACs to access the wireless network. Deny: deny the hosts with the following listed MACs to access the wireless network. Click Add to add the MACs. MAC Address: Enter the MAC address(es) or select the MAC address(es). The format of MAC address could be: xx:xx:xx:xx:xx:xx or xx-xx-xx-xx-xx-xx.
Wireless Bridge WDS (wireless distributed system) is a wireless access point mode that enables wireless link and communication with other access points. It’s easy to install, simply define the peer’s MAC address of the connected AP. WDS takes advantage of cost saving and flexibility with no extra wireless client device required to bridge between two access points and extending an existing wired or wireless infrastructure network to create a larger network.
Remote Bridge MAC Address: select the remote bridge MAC addresses. Disable: Does not restrict the gateway communicating with bridges that have their MAC address listed, but it is still open to communicate with all bridges that are in the same network. Click Apply to apply your settings.
Advanced Here users can set some advanced parameters about wireless. Band: select frequency band. Here 2.4GHz. Channel: Allows channel selection of a specific channel (1-7) or Auto mode. Scan Used Channel: Press the button to scan and list all channels being used. Auto Channel Timer (min): The auto channel times length it takes to scan in minutes. Only available for auto channel mode. 802.11n/EWC: select to auto enable or disable 802.11n. Bandwidth: Select bandwidth.
RIFS Advertisement: Reduced Inter-frame Spacing (RIFS) is a 802.11n feature that also improves performance by reducing the amount of dead time required between OFDM transmissions. Select Off to disable this function or auto to enable this function. OBSS Co-Existence: coexistence (or not) between 20 MHZ and 40 MHZ overlapping basic service sets (OBSS) in wireless local area networks. RX Chain Power Save: Enabling this feature turns off one of the Receive chains, going from 2x2 to 2x1 to save power.
Station Info Here you can view information about the wireless clients. MAC Address: The MAC address of the wireless clients. Associated: List all the stations that are associated with the Access Point. If a station is idle for too long, it is removed from this list Authorized: List those devices with authorized access. SSID: Show the current SSID of the client. Interface: To show which interface the wireless client is connected to. Refresh: To get the latest information.
Schedule Control Schedule control is aimed to offer methods to flexibly control when the wireless network (SSID) is allowed for access. The Wireless schedule only functions whilst Wireless is enabled. The Guest/Virtual AP schedule control only operates whilst the associated AP is enabled. For detail setting the timeslot, user can turn to Time Schedule . Time Schedule: Set when the SSID works.
WAN-Wide Area Network A WAN (Wide Area Network) is a computer network that covers a broad geographical area (eg. Internet) that is used to connect LAN and other types of network systems. WAN Service Two WAN interfaces are provided for WAN connection: DSL and Ethernet. Click Add to add new WAN connections.
PPPoE PPPoE (PPP over Ethernet) provides access control in a manner which is similar to dial-up services using PPP. VCP/VPI: Enter the VCI/VPI combination from you ISP. Encapsulation Mode: Select the encapsulation mode, LLC/SNAP-BRIDGING, or VC/MUX. Description: User-defined description for the connection, commonly for friendly use. 802.
Note: In PPPoE connection, NAT is enabled by default, you can determine whether to enable Fullcone NAT or disable Fullcone NAT and only use NAT, the default NAT type is Port Restricted cone NAT. Of Port-Restricted cone NAT, the restriction includes port numbers. Specifically, an external host can send a packet, with source IP address X and source port P, to the internal host only if the internal host had previously sent a packet to IP address X and port P.
Default Gateway Select default gateway for you connection (IPv4 and IPv6). DNS IPv4 Three ways to set an IPv4 DNS server Available WAN interfaces: Select a desirable WAN interface as the IPv4 DNS server. Static DNS Address: To specify DNS server manually by entering your primary and secondary DNS server addresses.
If you don’t need a service, select the item you want to remove, check the checkbox, then press Remove. Press Edit button to re-edit this service settings.
Here you can configure WAN Service, if it is OK, you can access the internet. You can go to Status >WAN or Summary to view the WAN connection information (if your ISP provides IPv6 service, then you will obtain an IPv6 address).
PPPoA VCP/VPI: Enter the VCI/VPI combination from you ISP. Encapsulation Mode: Select the encapsulation mode, LLC/SNAP-BRIDGING, or VC/MUX. Description: User-defined description for the connection. Username: Enter the account obtained from the ISP. Password: Enter the password obtained from the ISP. Authentication Method: Default is Auto. Or else your ISP will advise you the appropriate mode. Firewall: Enable to drop all traffic from WAN side.
IPv6 for this service: Enable to use IPv6 service. IPv6 Address: Select whether to set static IPv6 address or obtain automatically. IP Address: If Static is enabled in the above field, enter the static IPv4 address. MTU: Maximum Transmission Unit, the size of the largest datagram (excluding media-specific headers) that IP will attempt to send through the interface. IGMP Multicast Proxy: Check whether to enable this feature.
IP over Ethernet VCP/VPI: Enter the VCI/VPI combination from you ISP. Encapsulation Mode: Select the encapsulation mode, LLC/SNAP-BRIDGING, or VC/MUX. Description: User-defined description for the connection, commonly for friendly use. Authentication Method: Default is Auto. Or else your ISP will advise you the appropriate mode. 802.
Default setting is Disable. WAN IP Address: Enter your IPv4 address to the device provided by your ISP. WAN Subnet Mask: Enter your submask to the device provided by your ISP. WAN gateway IP Address: Enter your gateway IP address to the device provided by your ISP. IPv6 for this service: Enable to use IPv6 service. Obtain an IPv6 address automatically: check whether to enable or disable this feature. WAN IPv6 Address/Prefix Length: Enter the WAN IPv6 Address/Prefix Length from your ISP.
IPoA VCP/VPI: Enter the VCI/VPI combination from you ISP. Encapsulation Mode: Select the encapsulation mode, LLC/SNAP-BRIDGING, or VC/MUX. Description: User-defined description for the connection, commonly for friendly use. WAN IP: Enter the WAN IP from the ISP. WAN Subnet Mask: Enter the WAN Subnet Mask from the ISP. NAT: The NAT (Network Address Translation) feature allows multiple users to access the Internet through a single IP account by sharing the single IP address.
Bridging VCP/VPI: Enter the VCI/VPI combination from you ISP. Encapsulation Mode: Select the encapsulation mode, LLC/SNAP-BRIDGING, or VC/MUX. Description: User-defined description for the connection, commonly for friendly use. 802.1P Priority: The parameter indicates the frame priority level from 0 (lowest) to 7 (highest), which can be used to prioritize different classes of traffic (voice, video, data, etc). Enter the priority identification, tagged: 0-1, untagged: -1. 802.
Ethernet Ethernet WAN connection is well known as directly broadband WAN connection. PPPoE Description: User-defined description for the connection, commonly for friendly use. 802.1P Priority: The parameter indicates the frame priority level from 0 (lowest) to 7 (highest), which can be used to prioritize different classes of traffic (voice, video, data, etc). Enter the priority identification, tagged: 0-1, untagged: -1. 802.1Q VLAN ID: It is a parameter to specify the VLAN which the frame belongs.
identification, tagged: 0-4094, untagged : -1. Username: Enter the account obtained from the ISP. Password: Enter the password obtained from the ISP. Service Name: The item is for identification purpose, user can define it yourselfe. Authentication Method: Default is Auto. Or else your ISP will advise you the appropriate mode. Firewall: Enable to drop all traffic from WAN side. If enabled, all incoming packets by default would be dropped, and please turn to IP Filtering Incoming to add allowing rules.
Click Next to continue to set the default gateway and DNS for IPv4 and IPv6. Default Gateway Select default gateway for you connection (IPv4 and IPv6). DNS IPv4 Three ways to set an IPv4 DNS server Available WAN interfaces: Select a desirable WAN interface as the IPv4 DNS server. Static DNS Address: To specify DNS server manually by entering your primary and secondary DNS server addresses.
If you don’t need the service, select the item you want to remove, check the checkbox, then press Remove, it will be OK. Press Edit button to re-edit this service settings. Here the corresponding WAN Service have been configured, if it is OK, you can access the internet. You can go to Status>WAN or Summary to view the WAN connection information (if your ISP provides IPv6 service, then you will obtain an IPv6 address).
IP over Ethernet Description: User-defined description for the connection, commonly for friendly use. 802.1P Priority: The parameter indicates the frame priority level from 0 (lowest) to 7 (highest), which can be used to prioritize different classes of traffic (voice, video, data, etc). Enter the priority identification, tagged: 0-1, untagged: -1. 802.1Q VLAN ID: It is a parameter to specify the VLAN which the frame belongs. Enter the VLAN ID identification, tagged: 0-4094, untagged : -1.
Obtain an IPv6 address automatically: check whether to enable or disable this feature. WAN IPv6 Address/Prefix Length: Enter the WAN IPv6 Address/Prefix Length from your ISP. WAN Next-Hop IPv6 Address: Enter the WAN Next-Hop IPv6 Address from your ISP. Note: If you don’t know well about the DHCP Option, you can leave it empty or leave it as default. NAT: The NAT (Network Address Translation) feature allows multiple users to access the Internet through a single IP account by sharing the single IP address.
Bridging Description: User-defined description for the connection, commonly for friendly use. 802.1P Priority: The parameter indicates the frame priority level from 0 (lowest) to 7 (highest), which can be used to prioritize different classes of traffic (voice, video, data, etc). Enter the priority identification, tagged: 0-1, untagged: -1. 802.1Q VLAN ID: It is a parameter to specify the VLAN which the frame belongs. Enter the VLAN ID identification, tagged: 0-4094, untagged : -1.
3G/LTE Select 3G/LTE to configure the route to enjoy the mobility. Given that BiPAC 7820NZ supports dual SIM mobile connectivity, please determine which SIM you are gonna use or both (3G/LTE failover), and set the exact required connecting information for each SIM (SIM1 and SIM2). By default the 3G/LTE interface is on, user can edit the parameters to meet your own requirements. Click Edit button to enter the 3G/LTE configuration page.
Failover: If enabled, the 3G/LTE will work in failover mode and be brought up only when there is no active default route. In this mode, 3G/LTE work as a backup for the WAN connectivity. While if disabled, 3G/LTE serves as a normal interface, and can only be brought up when it has been configured to achieve a mobile connectivity. SIM 1 & SIM 2 Mode: There are 6 options of phone service standards: GSM 2G only, UTMS 3G only, GSM 2G preferred, UMTS 3G preferred, Automatic, and Use 3G/LTE 3g dongle settings.
service provider is able to attach anything to an APN to create a data connection, requirements for APNs varies between different service providers. Most service providers have an internet portal which they use to connect to a DHCP Server, thus giving you access to the internet i.e. some 3G operators use the APN ‘internet’ for their portal. The default value is “internet”. Username/Password: Enter the username and password provided by your service provider. The username and password are case sensitive.
Click Apply to confirm the settings. Here you can configure WAN Service, if it is OK, you can access the internet. You can go to Status >WAN or Summary to view the WAN connection information (Here user can see the 3G/LTE failover).
Dual SIM BiPAC 7820NZ offers dual-SIM slots for two mobile SIM cards. The SIM 1 will be in use when two SIM cards are both up. The current SIM connection will fail over to the other SIM connection when the situation below happens. But note when the failover is done, the connection cannot fail back to the previous SIM connection. Failover: Check Enable to activate failover feature. Connectivity Decision: Set how many times of probing failure to switch to the other SIM.
DSL This screen allows you to set DSL parameters. DSL knowledge is required to configure these settings. Contact your ISP to make sure that these parameters are correct. Modulation: There are 7 modes “G.Dmt”, “G.lite”, “T1.413”, “ADSL2”, “AnnexL”, ”ADSL2+”, “AnnexM” that user can select for this connection. Phone line pair: This is for reserved only. You can choose "Inner Pair" or "Outer Pair". Capability: There are 2 options “Bitswap Enable” and “SRA Enable” that user can select for this connection.
With each tone carrying separate data, the technique operates as if 256 separate modems were running in parallel.
SNR Signal-to-noise ratio (often abbreviated SNR or S/N) is a measure used in science and engineering that compares the level of a desired signal to the level of background noise. It is defined as the ratio of signal power to the noise power. SNR: Change the value to adjust the DSL link rate, more suitable for an advanced user.
System Internet Time The router does not have a real time clock on board; instead, it uses the Network Time Protocol (NTP) to get the most current time from an NTP server. NTP is a protocol for synchronization of computers. It can enable computers synchronize to the NTP server or clock source with a high accuracy.
Firmware Upgrade Software upgrading lets you experience new and integral functions of your router. Restart device with: Factory Default Settings: Restart the device with factory default settings automatically when finishing upgrading. Current Settings: Restart the device with the current settings automatically when finishing upgrading. Your router’s “firmware” is the software that allows it to operate and provides all its functionality.
Backup / Update These functions allow you to save and backup your router’s current settings to a file on your PC, or to restore from a previously saved backup. This is useful if you wish to experiment with different settings, knowing that you have a backup handy in the case of any mistakes. It is advisable to backup your router’s settings before making any significant changes to your router’s configuration.
Access Control Access Control is used to prevent unauthorized access to the router configuration page. Here you can change the login user password. Three user levels are provided here. Each user level there’s a default provided user. You must access the router with the appropriate username and password. Here the corresponding passwords are allowed to change. Level: select which level you want to change password to. There are three default levels.
Mail Alert Mail alert is designed to keep system administrator or other relevant personnel alerted of any unexpected events that might have occurred to the network computers or server for monitoring efficiency. With this alert system, appropriate solutions may be tackled to fix problems that may have arisen so that the server can be properly maintained. WAN Port: Mail Alert feature can be applicable to every WAN mode: Ethernet，DSL and 3G/LTE. Select the port you want to use Mail Alert.
SMS Alert SMS, Short Message Service, is to inform clients the information clients subscribe. The BiPAC 7820NZ offers SMS alert sending clients alert messages when a WAN IP change is detected. Recipient’s Number (WAN IP Change Alert): Enter the Recipient’s number that will receive the alert message once a WAN IP change has been detected.
Configure Log Log: Enable or disable this function. Log level: Select your log level. The log level allows you to configure which types of events are logged.
USB Storage here refers to network sharing in the network environment, USB devices act as the storage carrier for DLNA, NAS (Samba server, FTP server). Storage Device Info This part provides users direct access to the storage information like the total volume, the used and the remaining capacity of the device. Volume Name: Display the storage volume name FileSystem: Display the storage device’s file system format, well-known is FAT. Total Space: Display the total space of the storage, with unit MB.
User Account Users here can add user accounts for access to the storage, in this way users can access the network sharing storage with the specified account, and again protect their own data. Users added here are entitled to have access to both Samba server and FTP server. Default user admin. Click Add button, enter the user account-adding page: Username: user-defined name, but simpler and more convenient to remember would be favorable. Password: Set the password.
How to access Samba: In your computer, Click Start > Run, enter \\192.168.1.
When accessing the network storage, you can see a folder named “public”, users should have the account to enter, and the account can be set at the User Accounts section. When first logged on to the network folder, you will see the “public” folder. Public: The public sharing space for each user in the USB Storage. When user register a USB account and log successfully, a private folder (the same name as the user account registered) exclusive for each user is established. Go on to see the details.
Access the folder public.
When successfully accessed, the private folder of each user is established, and user can see from the following picture. The test fold in the picture is the private space for each user.
How to use FTP: Please note to enable remote FTP access in Remote Access. 1. Access via FTP tools Take popular FTP tool of FlashFXP for example: 1) Open FlashFXP 2) Create ftp sites (LAN IP / WAN IP, and set the account, port). 3) Connect to the ftp site.
2. Web FTP access 1) Enter ftp://admin@WAN-IP or ftp://admin@LAN-IP at the address bar of the IE. In terms of other browsers, type ftp://WAN-IP or ftp:// LAN-IP directly. 2) Enter the account's username and password.
Print Server The Print Server feature allows you to share a printer on your network by connecting a USB cable from your printer to the USB port on the 7820NZ. This allows you to print from any location on your network. Note: Only USB printers are supported Setup of the printer is a 3 step process (7820NZ for example) 1. Connect the printer to the 7820NZ’s USB port 2. Enable the print server on the 7820NZ 3.
Step 2: Click ‘’Add a Printer’’.
Step 4: Click “The printer that I want isn’t listed” Step 5: Select “Select a shared printer by name” Enter http://7820NZ- LAN-IP:631/printers/printer-name or. Make sure printer’s name is the same as what you set in the 7820NZ earlier For Example: http://192.168.1.
Step 6: Click “Next” to add the printer driver. If your printer is not listed and your printer came with an installation disk, click “Have Disk” find it and install the driver.
Step 8: Click “Next” and you are done You will now be able to see your printer on the Devices and Printers Page 150
DLNA The Digital Living Network Alliance (DLNA) is a non-profit collaborative trade organization established by Sony in June 2003, which is responsible for defining interoperability guidelines to enable sharing of digital media between consumer devices such as computers, printers, cameras, cell phones and other multiple devices. DLNA uses Universal Plug and Play (UPnP) for media management, discovery and control.
Take Windows media player in Windows 7 accessing the DLNA server for example for usage of DLNA .
IP Tunnel An IP Tunnel is an Internet Protocol (IP) network communication channels between two networks of different protocols. It is used to transport another network protocol by encapsulation of its packets. IP Tunnels are often used to connect two disjoint IP networks that do not have a native routing path to each other, via an underlying routable protocol across an intermediate transport network, like VPN.
Associated WAN Interface: The applied WAN interface with the set tunnel, thus when there are packets from/to the WAN interface, the tunnel would be used to transport the packets. Associated LAN Interface: Set the linked LAN interface with the tunnel. Method: 6rd operation mechanism: manually configured or automatically configured. If manually, please fill out the following 6rd parameters.
IPv4inIPv6 4in6 refers to tunneling of IPv4 in IPv6. It is an inherent internet interoperation mechanism allowing IPv4 to be used in an IPv6 only network. 4in6 uses tunneling to encapsulate IPv4 traffic over configured IPv6 tunnels. 4in6 tunnels are usually manually configured but they can be automated using protocols such as TSP to allow easy connection to a tunnel broker. DS – Lite DS –Lite, or Dual-Stack Lite, is designed to let an ISP omit the deployment of any IPv4 address to the customer’s CPE.
Security IP Filtering Outgoing IP filtering enables you to configure your router to block specified internal/external users (IP address) from Internet access, or you can disable specific service requests (Port number) to /from Internet. The relationship among all filters is “or” operation, which means that the router checks these different filter rules one by one, starting from the first rule. As long as one of the rules is satisfied, the specified action will be taken.
above. Destination Port [port or port: port]: Traffic with the particular set destination port or port in the set port range is to be blocked from going through the router. Default is set port from port range: 1 – 65535. Time Schedule: Select or set exactly when the rule works. When set to “Always On”, the rule will work all time; and also you can set the precise time when the rule works, like 01:00 - 19:00 from Monday to Friday.
(Rule inactive) 158
IP Filtering Incoming Incoming IP Filtering is set by default to block all incoming traffic, but user can set rules to forward the specific incoming traffic. Note: 1. The maximum number of entries: 32. 2. When LAN side firewall or firewall in WAN interface(s) is enabled, user can move here to add allowing rules to pass through the firewall. Click Add button to enter the exact rule setting page. Filter Name: A user-defined rule name.
Time Schedule: Select or set exactly when the rule works. When set to “Always On”, the rule will work all time; and also you can set the precise time when the rule works, like 01:00-19:00 from Monday to Friday. Or you can select the already set timeslot in “Time Schedule” during which the rule works. And when set to “Disable”, the rule is disabled or inactive and there will be an icon” ” in the list table indicating the rule is inactive. See Time Schedule.
MAC Filtering MAC Filtering is only effective on ATM PVCs configured in Bridged mode. FORWARDED means that all MAC layer frames will be forwarded except those matching with any of the specified rules in the following table. BLOCKED means that all MAC layer frames will be blocked except those matching with any of the specified rules in the following table.
Blocking WAN PING This feature is enabled to let your router not respond to any ping command when someone others “Ping” your WAN IP.
Time Restriction A MAC (Media Access Control) address is the unique network hardware identifier for each PC on your network’s interface (i.e. its Network Interface Card or Ethernet card). Using your router’s MAC Address Filter function, you can configure the network to block specific machines from accessing your LAN during the specified time. This page adds time of day restriction to a special LAN device connected to the router.
An example: Here you can see that the user “child-use” with a MAC of 18:a9:05:04:12:23 is blocked to access the router from 00:00 to 23:59 Monday through Friday. The “test” can access the internet always. If you needn’t this rule, you can check the box, press Remove, it will be OK. .
URL Filter URL (Uniform Resource Locator – e.g. an address in the form of http://www.abcde.com or http://www.example.com) filter rules allow you to prevent users on your network from accessing particular websites by their URL. There are no pre-defined URL filter rules; you can add filter rules to meet your requirements. Note: 1) URL Filter rules apply to both IPv4 and IPv6 sources. 2) But in Exception IP Address part, user can click IPv4 and IPv6 respectively.
Keywords Filtering Note: Maximum number of entries: 32. Click to add the keywords. Enter the Keyword, for example image, and then click Add. You can add other keywords like this. The keywords you add will be listed as above. If you want to reedit the keyword, press the Edit radio button left beside the item, and the word will listed in the Keyword field, edit, and then press Edit/Delete to confirm. If you want to delete certain keyword, check Delete checkbox right beside the item, and press Edit/Delete.
Filtering. Exception IP Address In the section, users can set the exception IP respectively for IPv4 and IPv6. Click to add the IP Addresses. Enter the except IP address. Click Add to save your changes. The IP address will be entered into the Exception List, and excluded from the URL filtering rules in effect. For specific process, please refer to Keywords Filtering. For example, users can set IPv4 client 192.168.1.
Parental Control Provider Parental Control Provider provides Web content filtering offering safer and more reliable web surfing for users. Please get an account and configure at the selected Provider “www.opendns.com” in advance. To use parental control (DNS), user needs to configure to use parental control (DNS provided by parental control provider) to access internet at WAN configuration or DNS page(See DNS).
QoS - Quality of Service QoS helps you to control the data upload traffic of each application from LAN (Ethernet) to WAN (Internet). This feature allows you to control the quality and speed of throughput for each application when the system is running with full upstream load. Note: ADSL line speed is based on the ADSL sync rate. But there is no QoS on 3G/LTE as the 3G/LTE line speed is various and can not be known exactly.
DSCP value.
External IP Address: The IP address on remote / WAN side. External Port: The Port number on the remote / WAN side. Time Schedule: Select or set exactly when the rule works. When set to “Always On”, the rule will work all time; and also you can set the precise time when the rule works, like 01:00-19:00 from Monday to Friday. Or you can select the already set timeslot in “Time Schedule” during which the rule works.
Examples: Common usage 1. Give outgoing VoIP traffic more priority. The default queue priority is normal, so if you have VoIP users in your local network, you can set a higher priority to the outgoing VoIP traffic. 2.
3. If you are actively engaged in P2P and are afraid of slowing down internet access for other users within your network, you can then use QoS to set a rule that has low priority. In this way, P2P application will not congest the data transmission with other applications. Other applications, like FTP, Mail access, users can use QoS to control based on need.
QoS Port Shaping QoS port shaping supports traffic shaping of Ethernet interfaces. It forcefully maximizes the throughput of the Ethernet interface. When “Shaping Rate” is set to “-1”, no shaping will be in place and the “Burst Size” is to be ignored. Interface: P1-P4. P4 used as EWAN also covered. Type: All LAN when P4 is LAN port; P4 used as EWAN, type WAN and all others LAN. QoS Shaping Rate (Kbps): Set the forcefully maximum rate. Burst Size(Bytes): Set the forcefully Burst Size.
NAT NAT (Network Address Translation) feature translates a private IP to a public IP, allowing multiple users to access the Internet through a single IP account, sharing the single IP address. It is a natural firewall for the private network. Exceptional Rule Group Exceptional Rule is dedicated to giving or blocking Virtual Server/ DMZ access to some specific IP or IPs(range). Users are allowed to set 8 different exceptional rule groups at most. In each group, user can add specific IP or IP range.
Exceptional Rule Range IP Address Range: Specify the IP address range; IPv4 address range can be supported. Click Add to add the IP Range. For instance, if user wants to block IP range of 172.16.1.102-172.16.1.106 from accessing your set virtual server and DMZ host, you can add this IP range and valid it.
Virtual Servers In TCP/IP and UDP networks a port is a 16-bit number used to identify which application program (usually a server) incoming connections should be delivered to. Some ports have numbers that are pre-assigned to them by the IANA (the Internet Assigned Numbers Authority), and these are referred to as “well-known ports”. Servers follow the well-known port assignments so clients can locate them. If you wish to run a server on your network that can be accessed from the WAN (i.e.
The following configuration page will appear to let you configure. Interface: select from the drop-down menu the interface you want the virtual server(s) to apply. Server Name: select the server name from the drop-down menu. Custom Service: It is a kind of service to let users customize the service they want. Enter the userdefined service name here. It is a parameter only available when users select Custom Service in the above parameter. Server IP Address: Enter your server IP Address here.
access to a group of IPs. For example, as we set previously group 1 blocking access to 172.16.1.102-172.16.1.106. If here you want to block Virtual Server access to this IP range, you can select Group1. Set up 1. Select a Server Name from the drop-down menu, then the port will automatically appear, modify some as you like, or you can just leave it as default. Remember to enter your server IP Address. 2. Press Apply to conform, and the items will be list in the Virtual Servers Setup table.
( Means the rule is inactive) Remove If you don’t need a specified Server, you can remove it. Check the check box beside the item you want to remove, then press Remove, it will be OK.
DMZ Host The DMZ Host is a local computer exposed to the Internet. When setting a particular internal IP address as the DMZ Host, all incoming packets will be checked by Firewall and NAT algorithms before being passed to the DMZ host, when a packet received does not use a port number used by any other Virtual Server entries. (Group Information) DMZ Host IP Address: Enter the IP Address of a host you want it to be a DMZ host. Select from the list box to quick set the DMZ.
One-to-One NAT One-to-One NAT maps a specific private/local address to a global/public IP address. If user has multiple global/public IP addresses from your ISP, you are free to use one-to-one NAT to assign some specific public IP for an internal IP like a public web server mapped with a global/public IP for outside access. Valid: Check whether to valid the one-to-one NAT mapping rule. WAN Interface: Select one based WAN interface to configure the one-to-one NAT.
Port Triggering Port triggering is a way to automate port forwarding with outbound traffic on predetermined ports (‘triggering ports’), incoming ports are dynamically forwarded to the initiating host, while the outbound ports are in use. Port triggering triggers can open an incoming port when a client on the local network makes an outgoing connection on a predetermined port or a range of ports. Click Add to add a port triggering rule.
Open port Start: Enter a port number as the open port staring number. End: Enter a port number as the open port ending number. Any port in the range delimited by the ‘Start’ and ‘End’ would be the preset forwarding port or open port. Protocol: select the protocol this service used: TCP/UDP, TCP, UDP. Set up An example of how port triggering works, when a client behind a NAT router connecting to Aim Talk, it is a TCP connection with the default port 4099.
Edit/Remove If you don’t need a specified Server, you can remove it. Check the check box beside the item you want to remove, and then press Remove. Click Edit to re-edit your port-triggering rule.
