Security Packet Filter Packet filtering enables you to configure your router to block specified internal/external users (IP address) from Internet access, or you can disable specific service requests (Port number) to /from Internet. The relationship among all filters is “or” operation, which means that the router checks these different filter rules one by one, starting from the first rule. As long as one of the rules is satisfied, the specified action will be taken. Above is the listing table.
to. Only when RAW is selected, then you can type the protocol number (0-254) to identify the protocol that you want the filter applies to. When Any is selected, it means the filter will applies to any protocol. Internal Port: This Port or Port Range defines the ports allowed to be used by the Remote/WAN to connect to the application. Default is set from range 1 ~ 65535. It is recommended that this option be configured by an advanced user.
Remove Check the checkbox, press Remove, the item will be removed. Reorder When there are more than one Filter application, you can reorder them to the priority you want. The former is prior to the latter one. Click or to change the priority of the filter, then press 85 to confirm.
Parental Control Time Restriction A MAC (Media Access Control) address is the unique network hardware identifier for each PC on your network’s interface (i.e. its Network Interface Card or Ethernet card). Using your router’s MAC Address Filter function, you can configure the network to block specific machines from accessing your LAN during the specified time. Action: L Disable: disable the Time Restriction function. L Allow: allow the members in the following table to access the router.
Start Time: enter the start time of each day in hh:mm format. Leaving it empty means 00:00. End Time: enter the end time of each day in hh:mm format. Leaving it empty means 23:59. Click Apply to confirm your settings. The following prompt window will appear to remind you of the attention. If you needn’t this rule, you can check the box, press Remove, it will be OK. URL Filter URL (Uniform Resource Locator – e.g. an address in the form of http://www.abcde.com or http://www.example.
Keywords Filtering: Allow blocking against specific keywords within a particular URL rather than having to specify a complete URL (e.g.to block any image called “advertisement.gif”). When enabled, your specified keywords list will be checked to see if any keywords are present in URLs accessed to determine if the connection attempt should be blocked. Please note that the URL filter blocks web browser (HTTP) connection attempts using port 80 only.
Domain Filtering Click to add Domains. Domains Filtering: enter the domain you want this filter applies to. Type: select the action this filter deals with the Domain. L Forbidden Domain: the domain is the forbidden to access. L Trusted Domain: the domain is trusted and allowed access. Enter a domain and select whether this domain is trusted or forbidden with the pull-down menu. Next, click Add.
QoS - Quality of Service QoS helps you to control the data upload traffic of each application from LAN (Ethernet) to WAN (Internet). It facilitates you the features to control the quality and speed of throughput for each application when the system is running with full upstream load. Quality of Service: Check to activate this function and the following field will be available.
IP Precedence and DSCP Mapping Table Default (000000) EF(101110) AF11 (001010) AF12 (001100) AF13 (001110) AF21 (010010) AF22 (010100) AF23 (010110) AF31 (011010) AF32 (011100) AF33 (011110) AF41 (100010) AF42 (100100) AF43 (100110) CS1(001000) CS2(010000) CS3(011000) CS4(100000) CS5(101000) CS6(110000) CS7(111000) Mapping Table Best Effort Expedited Forwarding Assured Forwarding Class1(L) Assured Forwarding Class1(M) Assured Forwarding Class1(H) Assured Forwarding Class1(L) Assured Forwarding Class1(M) As
Queue Config Queue is a technology of managing congestion providing precautions with the packets storing and scheduling. Queue Config allows you to configure a QoS queue entry and assign it to a specific network interface. Each queue entry set here will be used by the classfier to place ingress packets appropriately. Note: the interface set in the WAN> WAN Interface will be list as Default Queue here, and the parameters listed above can be configured there.
Click Add to create a queue. Name: Type the name of the queue. Enable: Select whether to enable the queue. Interface: Select which interface this queue applies to. Select interface, the following corresponding parameters will appear to let you configure, Enter the information, Click Apply to conform. Then the item will be listed in the table. Precedence: the precedence of the queue, interface P1-P4, 4 levels from high to low are 1-4.
Click Apply to save and the added queue will be listed as below. Enable: check the enable check-box, then press Enable to activate the queue. If you want to disable this queue, you can uncheck the corresponding check-box and press Enable, the queue will be disabled. Remove: To delete the QoS rule from the table, check Remove checkbox then click Remove button to delete the selected item.
QoS Classification This screen displays a packet QoS summary table and allows user to add or remove a QoS classification class. This is the main place to configure the classification, marking and queuing rules. Click Add to add Network Traffic Class Rule.
The classification rule is a ‘AND’ mode, that is a rule takes effect only when all of the specified conditions must be satisfied. Parameters Traffic Class Name: Assign a name for this class to uniquely identify the others among multiple classes. Rule Order: Select the priority for this class rule. Rule Status: Select Enable to activate this class rule. Specify Classification Criteria The following parameters are to be classification rule. Enter or select appropriate parameters on the following fields.
Set up a QoS Classification IP QoS LAN to WAN IP QoS 1. It is a QoS controlling the traffic from LAN to WAN. So first make sure there is at least one WAN queue. If you have configured WAN interface and it will appeared as a default queue, you can also add other queues of the specific interface. See Queue Config. Here we have a atm0 (WAN interface), the interface has a default queue and an added queue. Make sure to enable the queue.
2. In QoS Classification Setup page, Click Add to add a Qos Classification. Then in the appeared Add Network Traffic Class Rule page, enter the information to set up a rule. 1) Specify the rule name, rule order, and rule status. 2) Specify the classification criteria. Here you can set every parameter to strictly control the specific traffic or you can set several parameters to let them be the key elements to control the traffic. A blank criterion indicates it is not used for classification.
3) Specify the classification results. Here you must Assign Classification Queue. Whether the following parameters are needed is according to your needs. If you do not want to change the original information, please leave it empty. The queues listed here in the Assign Classification Queue are WAN interface queues set in Queue Config section. Select the needed queue. If you find none queues here, turn back to check whether you have configured a queue and enable it. 3. Click Apply to save your settings.
WAN to LAN IP QoS 1. Here we take WAN to LAN (P1) QoS for example. Make sure there are enabled port P1 based queues here. LAN queues need your configuration. You can enable wireless to enable WMM queues by default or add P1-P4 ported based queues manually. 2. In QoS Classification Setup page, Click Add to add a Qos Classification.
Then in the Add Network Traffic Class Rule page, enter the information to set up a rule. 3. Click Apply to save your settings. The added rule will be listed as below.
Port-based QoS Take port P1 to WAN QoS for example. 1. First make sure there is at least a WAN queue and it is enabled. 2. In QoS Classification Setup page, Click Add to add a QoS Classification.
Then in the Add Network Traffic Class Rule page, enter the information to set up a rule to your needs. To Assign Classification queue, select the needed WAN queue. 3. Click Apply to save your settings and the added rule will be listed as below.
Routing Default Gateway To set default gateway and Available Routed WAN Interface. This interfaces are the ones you have set in WAN section, here select the one you want to be the default gateway by moving the interface via or . And select a Default IPv6 Gateway from the drop-down menu. Note: Only one default gateway interface will be used according to the priority with the first being the highest and the last one the lowest priority if the WAN interface is connected.
Static Route With static route feature, you are equipped with the capability to control the routing of the all the traffic across your network. With each routing rule created, you can specifically assign the destination where the traffic will be routed to. Above is the static route listing table, click Add to create static routing. IP Version: select the IP version, IPv4 or IPv6. Destination IP Address / Prefix Length: enter the destination IP address and the prefix length.
In listing table you can remove the one you don’t want by checking the checking box and press Remove button.
Policy Routing Here users can set a route for the host (source IP) in a LAN interface to access outside through a specified Default Gateway or a WAN interface. The following is the policy Routing listing table. Click Add to create a policy route. Policy Name: user-defined name. Physical LAN Port: select the LAN port. Source IP: enter the Host Source IP. Interface: select the WAN interface which you want the Source IP to access outside through.
RIP RIP, Router Information Protocol, is a simple Interior Gateway Protocol (IGP). RIP has two versions, RIP-1 and RIP-2. Interface: the interface the rule applies to. Version: select the RIP version, there are two versions, RIP-1 and RIP-2. Operation: RIP has two operation mode. L Passive: only receive the routing information broadcasted by other routers and modifies its routing table according to the received information.
DNS DNS, Domain Name System, is a distributed database of TCP/IP application. DNS provides translation of Domain name to IP. IPv6 DNS Server IPv6 DNS Server’s operation is similar to IPv4 DNS server. There are two modes to get DNS server address: Auto and Static mode. Obtain IPv6 DNS info from a WAN interface WAN Interface selected: select one configured IPv6 WAN connection from the drop-down menu to be as an IPv6 DNS.
Dynamic DNS The Dynamic DNS function allows you to alias a dynamic IP address to a static hostname, allowing users whose ISP does not assign them a static IP address to use a domain name. This is especially useful for hosting servers via your ADSL connection, so that anyone wishing to connect to you may use your domain name, rather than having to use your dynamic IP address, which changes fromtime to time. This dynamic IP address is the WAN IP address of the router, which is assigned to you by your ISP.
DSL This screen allows you to set DSL parameters. DSL knowledge is required to configure these settings. Contact your ISP to make sure that these parameters are correct. Modulation: There are 7 modes “G.Dmt”, “G.lite”, “T1.413”, “ADSL2”, “AnnexL”, ”ADSL2+”, “AnnexM” that user can select for this connection. Phone line pair: This is for reserved only. You can choose "Inner Pair" or "Outer Pair". Capability: There are 2 options “Bitswap Enable” and “SRA Enable” that user can select for this connection.
With each tone carrying separate data, the technique operates as if 256 separate modems were running in parallel.
UPnP UPnP offers peer-to-peer network connectivity for PCs and other network devices, along with control and data transfer between devices. UPnP offers many advantages for users running NAT routers through UPnP NAT Traversal, and on supported systems makes tasks such as port forwarding much easier by letting the application control the required settings, removing the need for the user to control advanced configuration of their device.
Installing UPnP in Windows Example Follow the steps below to install the UPnP in Windows Me. Step 1: Click Start and Control Panel. Double-click Add/Remove Programs. Step 2: Click on the Windows Setup tab and select Communication in the Components selection box. Click Details. Step 3: In the Communications window, select the Universal Plug and Play check box in the Components selection box. Step 4: Click OK to go back to the Add/Remove Programs Properties window. Click Next.
Follow the steps below to install the UPnP in Windows XP. Step 1: Click Start and Control Panel. Step 2: Double-click Network Connections. Step 3: In the Network Connections window, click Advanced in the main menu and select Optional Networking Components …. The Windows Optional Networking Components Wizard window displays. Step 4: Select Networking Service in the Components selection box and click Details.
Step 5: In the Networking Services window, select the Universal Plug and Play check box. Step 6: Click OK to go back to the Windows Optional Networking Component Wizard window and click Next. Auto-discover Your UPnP-enabled Network Device Step 1: Click start and Control Panel. Double-click Network Connections. An icon displays under Internet Gateway. Step 2: Right-click the icon and select Properties.
Step 3: In the Internet Connection Properties window, click Settings to see the port mappings that were automatically created. Step 4: You may edit or delete the port mappings or click Add to manually add port mappings. Step 5: Select Show icon in notification area when connected option and click OK.
in the system tray Step 6: Double-click on the icon to display your current Internet connection status.
Web Configurator Easy Access With UPnP, you can access web-based configuration for the BiPAC 7800NEXL without first finding out the IP address of the router. This helps if you do not know the router’s IP address. Follow the steps below to access web configuration. Step 1: Click Start and then Control Panel. Step 2: Double-click Network Connections. Step 3: Select My Network Places under Other Places. Step 4: An icon describing each UPnP-enabled device shows under Local Network.
DNS Proxy DNS proxy is used to forward request and response message between DNS Client and DNS Server. Hosts in LAN can use router serving as a DNS proxy to connect to the DNS Server in public to correctly resolve Domain name to access the internet. DNS Proxy: select whether to enable or disable DNS Proxy function, default is enabled. Host name of the Broadband Router: enter the host name of the router. Default is home.gateway. Domain name of the LAN network: enter the domain name of the LAN network. home.
Interface Grouping Interface grouping is a function to group interfaces, known as VLAN. A Virtual LAN, commonly known as a VLAN, is a group of hosts with the common set of requirements that communicate as if they were attached to the same broadcast domain, regardless of the physical location. A VLAN has the same attributes as a physical LAN, but it allows for end stations to be grouped together even if they are not located on the same network switch. Click Add to add groups.
Group Name: type a group name. WAN interface used in the grouping: select from the drop-down box the WAN interface you want to applied in the group. Grouped LAN Interfaces: select the LAN interfaces you want to group as a single group from Available LAN Interfaces. Automatically Add Clients With following DHCP Vendor IDs: enter the DHCP Vendor IDs for which you want the Clients automatically added into the group. DHCP vendor ID (DHCP 60) is an Authentication for DHCP Messages.
Certificate This feature is used for TR069 ACS Server authentication of the device used certificate, if necessary. If the imported certificate doesn't match the authorized certificate of the ACS Server, the device will have no access to the server. Certificate Name: the certificate identification name. Subject: the certificate subject. Type: the certificate type information. "ca", indicates that the certificate is a CA-signed certificate.
Click Import Certificate button to import your certificate. Enter the certificate name and insert the certificate.
Click Apply to confirm your settings.
Multicast Multicast is one of the three network transmission modes, Unicast, Multicast, Broadcast. It is a transmission mode that supports point-to-multipoint connections between the sender and the recipient. IGMP protocol is used to establish and maintain the relationship between IP host and the host directly connected multicast router. IGMP stands for Internet Group Management Protocol is a communications protocols used to manage the membership of Internet Protocol multicast groups.
IGMP Default Version: enter the supported IGMP version, 1-3, default is IGMP v3. Query Interval: enter the periodic query interval time (sec) the multicast router sending the query message to hosts to understand the group membership information. Query Response Interval: enter the response interval time (sec). Last Member Query Interval: enter the interval time (sec) the multicast router query the specified group after it has received leave message.
Wireless This section provides you ways to configure wireless access. When you click this item, the column will expand to display the sub-items that will lead you to configure your router. Basic, Secturity, MAC Filter, Wireless Bridge, Advanced and Station Info are included here.
Basic It let you determine whether to enable Wireless function and set the basic parameters of an AP and the Virtual APs. Wireless: Default setting is set to Enable. If you do not have any wireless devices, check the checkbox again to unselect. Hide SSID: It is function in which transmits its SSID to the air so that when wireless client searches for a network, router can then be discovered and recognized. Check the checkbox to determine whether you want to hide SSID.
physical Access Point (AP). When a single physical AP supports multiple “Virtual APs”, each Virtual AP appears to stations (STAs) to be an independent physical AP, even though only a single physical AP is present. For example, multiple Virtual APs might exist within a single physical AP, each advertising a distinct SSID and capability set.
Security Wireless security is the prevention of unauthorized access or damage to computers using wireless network. Manual Setup AP Select SSID: select the SSID you want these settings apply to. Network Authentication L Open WEP Encryption: select to enable or disable WEP Encryption. Here select Enable. Encryption Strength: select the strength, 128-bit or 64-bit. Current Network Key: select the one to be the current network key. Please refer to key 1- 4 below.
L Shared It is similar to network authentication ‘Open’. But here the WEP Encryption must be enabled. L 802.1x RADIUS Server IP Address: RADIUS( Remote Authentication Dial In User Service), Enter the IP address of RADIUS authentication server. RADIUS Server Port: Enter the port number of RADIUS authentication server here. RADIUS Key: Enter the password of RADIUS authentication server. WEP Encryption: select to enable or disable WEP Encryption. Here select Enable.
L WPA WPA Group ReKey Internal: The period of renewal time for changing the security key automatically between wireless client and Access Point (AP). The unit is second. RADIUS Server IP Address: RADIUS( Remote Authentication Dial In User Service), Enter the IP address of RADIUS authentication server. RADIUS Server Port: Enter the port number of RADIUS authentication server here. RADIUS Key: Enter the password of RADIUS authentication server.
preauthentication, it can perform 802.1X authentications to the new AP, and when handoff happens, this mode will help reduce the association time used. Network Re-auth Interval: the interval for network Re-authentication. The unit is second. WPA Group ReKey Internal: The period of renewal time for changing the security key automatically between wireless client and Access Point (AP). The unit is second.
L Mixed WPA2/WPA-PSk WPA/WAPI passphrase: enter the WPA.WAPI passphrase, you can click here to display to view it. WPA Group ReKey Internal: The period of renewal time for changing the security key automatically between wireless client and Access Point (AP). The unit is second. WPA/WAPI Encryption: There are two Algorithms, AES (Advanced Encryption Standard) and TKIP(Temporal Key Integrity Protocol) which help to protect the wireless communication.
Configure AP as Registrar Add Enrollee with PIN method 1. select radio button ‘PIN’. 2. Input PIN from Enrollee Station (16837546 in this example). Help: it is to help users to understand PIN. 3.Click .
3. Operate Station to start WPS Adding Enrollee. Launch the wireless client’s WPS utility (eg.Ralink Utility). Set the Config Mode as Enrollee, press the WPS button on the top bar, select the AP (eg. wlan-ap) from the WPS AP List column. Then press the PIN button located on the middle left of the page to run the scan.
4. The client’s SSID and security setting will now be configured to match the SSID and security setting of the registrar. You can check the message in the red ellipse with the security parameters you set, here we all use the default.
Add Enrollee with PBC Method 1. Select radio button “Push-Button” and Click router.
2. Operate Station to start WPS Adding Enrollee. Launch the wireless client’s WPS Utility (eg. Ralink Utility). Set the Config Mode as Enrollee. Then press the WPS button and choose the correct AP (eg. wlan-ap) from the WPS AP List section before pressing the PBC button to run the scan.
3. When the PBC button is pushed, a wireless communication will be established between your router and the PC. The client’s SSID and security setting will now be configured to match the SSID and security setting of the router.
Configure AP as Enrollee Add Registrar with PIN Method 1. Set AP to “Unconfigured Mode” and Click “Config AP” button.
2. Launch the wireless client’s WPS utility (eg. Ralink Utility). Set the Config Mode as Registrar. Enter the PIN number (76229909 for example) in the PIN Code column then choose the correct AP (eg. wlan-ap) from the WPS AP List section before pressing the PIN button to run the scan.
3. The router’s (AP’s) SSID and security setting will now be configured to match the SSID and security setting of the registrar. 4. Do Web Page refresh after ER complete AP Configuration to check the new parameters setting.
MAC Filter Select SSID: select the SSID you want this filter applies to. MAC Restrict Mode: L Disable: disable the MAC Filter function. L Allow: allow the hosts with the following listed MACs to access the wireless network. L Deny: deny the hosts with the following listed MACs to access the wireless network. Click Add to add the MACs. MAC Address: enter the MAC address(es). The format of MAC address could be: xx:xx:xx:xx:xx:xx or xx-xx-xx-xx-xx-xx.
Wireless Bridge WDS (wireless distributed system) is a wireless access point mode that enables wireless link and communication with other access point. It is easy to be installed, simply define the peer’s MAC address of the connected AP. WDS takes advantages of cost saving and flexibility which no extra wireless client device is required to bridge between two access points and extending an existing wired or wireless infrastructure network to create a larger network.
L Enabled (Scan): to enable wireless bridge restriction. Only those been scanned the gateway can communicate with. Remote Bridge MAC Address: select the remote bridge MAC addresses. L Disable: Does not restrict the gateway to communicating with bridges that have their MAC address listed, but it is still open to communicate with all bridges that are in the same network. Click Apply to apply your settings.
Advanced Here users can set some advanced parameters about wireless. Band: select frequency band. Here 2.4GHZ. Channel: Allows channel selection of a specific channel (1-7) or Auto mode. Auto Channel Timer(min): the auto channel times length it takes to scan in minutes. Only available for auto channel mode. 802.11n/EWC: select to auto enable or disable 802.11n. Bandwidth: Select bandwidth. The higher the bandwidth the better the performance will be. Control Sideband: only available for 40MHz.
802.11n Protection: turn off for maximized throughput. Auto for greater security. Support 802.11n Client Only: turn on the option is to only provide wireless access to the clients operating at 802.11n speeds. RIFS Advertisement: Reduced Inter-frame Spacing (RIFS) is a 802.11n feature that also improves performance by reducing the amount of dead time required between OFDM transmissions. Select Off to disable this function or auto to enable this function.
Station Info Here you can view the information about the wireless clients. MAC Address: the MAC address of the wireless clients. Associated: List all the stations that are associated with the Access Point. If a station is idle for too long, it is removed from this list Authorized: List those devices with authorized access. SSID: show the current SSID of the client. Interface: to show which interface the wireless client is connected to. Refresh: to get the latest information.
Management There are 9 items within the System section: System Log, SNMP Agent, TR-069 Client, Internet Time, Mail Alert, Wake on LAN, Access Control, Remote Access, Update Software and Backup/Update.
System Log To let users view or configure System Log. Click to configure the log. Log: enable or disable this function. Log level: select your log level. The log level allows you to configure which types of events are loged.
Click to see the System log of this router. The logs will be listed as configured above. Click refresh to get the latest information. Click Apply to save your settings.
SNMP Agent SNMP, Simple Network Management Protocol, is the most popular one in network. It consists of SNMP Manager，SNMP Agent and MIB. Every network device supporting SNMP will have a SNMP Agent which is a management software running in the device. SNMP Manager, the management software running the server, is to use SNMP protocol to send GetRequest、GetNextRequest, SetRequest message to Agent to view and change the information of the device.
TR- 069 Client TR-069 (short for Technical Report 069) is a DSL Forum (which was later renamed as Broadband Forum) technical specification entitled CPE WAN Management Protocol (CWMP). It defines an application layer protocol for remote management of end-user devices. It defines an application layer protocol for remote management of end-user devices. As a bidirectional SOAP/HTTP based protocol it can provides the communication between customer premises equipment (CPE) and Auto Configuration Server (ACS).
Connection Request User Name: Enter the username for ACS server to make connection request. Connection Request User Password: Enter the password for ACS server to make connection request. GetRPCMethods：supported by both CPE and ACS, display the supported RFC listing methods. Click Apply to apply your settings.
Internet Time The router does not have a real time clock on board; instead, it uses the Network Time Protocol (NTP) to get the most current time from an NTP server. NTP is a protocol for synchronization of computers. It can enable computers synchronize to the NTP server or clock source with a high accuracy.
Mail Alert Mail alert is designed to keep system administrator or other relevant personnels alerted of any unexpected events that might have occured to the network computers or server for monitoring efficiency. With this alert system, appropriate solutions may be tackled to fix problems that may have arisen so that the server can be properly maintained. SMTP Server: Enter the SMTP server that you would like to use for sending emails.
Wake on LAN Wake on LAN (WOL, sometimes WoL) is an Ethernet computer networking standard that allows a computer to be turned on or woken up remotely by a network message. Select: Select MAC address of the computer that you want to wake up or turn on remotely. Add: After selecting, click Add then you can perform the Wake-up action. Edit/Delete: Click to edit or delete the selected MAC address. Ready: “Yes” indicating the remote computer is ready for your waking up.
Access Control Access Control is used to prevent unauthorized access to the router configuration page. Here you can change the login user password. Three user levels are provided here. Each user level there’s a default provided user. You must access the router with the appropriate username and password. Here the corresponding passwords are allowed to change. Level: select which level you want to change password to. There are three default levels.
Remote Access It is to allow remote access to the router to view or configure. Remote: Select to enable or disable Remote Access functionality.
Update Software Software upgrading lets you experience the new and integral function of your router. Restart device with: L Factory Default Settings: Restart the device with factory default settings automatically when finished upgrading. L Current Settings: Restart the device with the current settings automatically when finished upgrading. Your router’s “firmware” is the software that allows it to operate and provides all its functionality.
Backup / Update These functions allow you to save and backup your router’s current settings to a file on your PC, or to restore from a previously saved backup. This is useful if you wish to experiment with different settings, knowing that you have a backup handy in the case of any mistakes. It is advisable to backup your router’s settings before making any significant changes to your router’s configuration.
Restart This section lets you restart your router if necessary. Click configuration page. in the low right corner of each If you wish to restart the router using the factory default settings (for example, after a firmware upgrade or if you have saved an incorrect configuration), select Factory Default Settings to reset to factory default settings. Or you just want to restart after the current setting, the select the Current Settings, and Click Restart.
Chapter 5: Troubleshooting If your router is not functioning properly, please refer to the suggested solutions provided in this chapter. If your problems persist or the suggested solutions do not meet your needs, please kindly contact your service provider or Billion for support. Problems with the router Problem Suggested Action Check the connection between the router and the adapter. If the problem persists, most likely it is due to the malfunction of your hardware.
Problem with LAN interface Problem Cannot PING any PC on LAN Suggested Action Check the Ethernet LEDs on the front panel. The LED should be on for the port that has a PC connected. If it does not lit, check to see if the cable between your router and the PC is properly connected. Make sure you have first uninstalled your firewall program before troubleshooting. Verify that the IP address and the subnet mask are consistent for both the router and the workstations.
Appendix: Product Support & Contact If you come across any problems please contact the dealer from where you purchased your product. Contact Billion Worldwide: http://www.billion.com FCC statement in the User’s Manual (for class B) “Federal Communication Commission (FCC) Statement” This Equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC rules.
