BiPAC 6200WZL R2/ 6200WZL R3 Moblie Broadband Wireless-N Router User Manual Version release: v1.04c.
d > K& KEd Ed^ , Wd Z ϭ͗ /EdZK h d/KE ͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘ ϭ /EdZK h d/KE dK zKhZ ZKhd Z ͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘ ϭ & dhZ ^ ͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘ Ϯ , Z t Z ^W /&/ d/KE^͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘ ϲ WW>/ d/KE^ / 'Z D ͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘ ϲ , Wd Z Ϯ͗ WZK h d Ks Zs/ t ͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘
& dKZz & h>d ^ dd/E'^ ͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘ ϭϵ /E&KZD d/KE &ZKD zKhZ /^W͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘ ϮϬ KE&/'hZ/E' t/d, zKhZ t ZKt^ Z ͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘ Ϯϭ , Wd Z ϰ͗ ^/ KE&/'hZ d/KE ͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘ϮϮ ^d dh^ ͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘ Ϯϯ Yh/ < ^d Zd ͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘
> E ;>ŽĐĂů ƌĞĂ EĞƚǁŽƌŬͿ ͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘ϰϮ ƚŚĞƌŶĞƚ ͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘ϰϮ /W ůŝĂƐ ͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘ϰϮ tŝƌĞůĞƐƐ ͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘ϰϯ tW^ ͘͘͘͘͘͘͘͘͘͘
YƵĂůŝƚLJ ŽĨ ^ĞƌǀŝĐĞ /ŶƚƌŽĚƵĐƚŝŽŶ ͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘ϴϬ YŽ^ ^ĞƚƵƉ ͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘ϴϬ s/Zdh > ^ Zs Z͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘ ϴϰ WŽƌƚ DĂƉƉŝŶŐ ͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘ϴϱ D ͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘͘
Chapter 1: Introduction Introduction to your Router Thank you for purchasing the Mobile Broadband Wireless-N Router. The router is an economic router ideal for SOHO users, office users and event organizers to have an improved wireless access with a speed of up to 150 Mbps. You can enjoy non-stop wireless access with this economic mobile 3G / 4G embedded router. With Dual-WAN design, you can also have an always-on WAN connection.
Features • 3G / 4G embedded with a built-in SIM card slot • Dual WAN interfaces for EWAN and 3G / 3.5G / 3.75G / 4G connections • 150Mbps.
• Stateful Packet Inspection (SPI) • Prevents DoS attacks including Land Attack, Ping of Death, etc. • Remote access control for web base access • Packet and URL filtering • Password protection for system management • VPN pass-through Quality of Service Control • Supports the DiffServ appoarch • Traffic prorization based-on IP protocol, port number and address Wireless LAN • Compliant with IEEE 802.11g and 802.11b standards • 2.4GHz - 2.
Hardware Specifications Physical interface • USB: 2 x USB 2.0 ports • 3G / 4G: 2 x antennas • Ethernet: 4 x 10 / 100Mbps Auto-MDI / MDI-X RJ-45 Ethernet ports • WAN: 1 x 10 / 100Mbps Auto-MDI / MDI-X RJ-45 Ethernet port (port #4 can be configured as WAN port for Broadband connectivity.) • Reset button • WPS push button • Power jack • Power switch • SIM slot : (for the SIM card from Telco / ISP) Physical Specifications • Dimensions: 7.28" x 4.86" x 1.38"(185mm x 123.
Chapter 2: Product Overview Important note for using this router Package Contents Mobile Broadband Wireless-N Router This Quick Installation Guide CD containing the user manual RJ-45 Ethernet Cable Two 3G/4G detachable antenna Power adaptor 7
Device Description The Front LEDs LED 1 2 3 Meaning Power Lit orange when the device is booting or the device fails to boot. Lit green when the device is ready. Lit green when one of LAN ports is connected to an Ethernet Ethernet (1 - 4 ) device. Blink when data is being Transmitted / Received. Lit green when connected to a Cable modem, xDSL modem, Fiber (PON) modem's Ethernet port well.
The Rear Ports 1 2 3 3G / 4G detachable Connect the 3G / 4G detachable antenna to this port. antenna Power Power ON/OFF switch Switch Power Jack Connect the supplied power adapter to this jack. 4 Reset Button Press it to reset the device or restore to factory default settings. 5 WPS Push WPS button to trigger Wi-Fi Protected Setup function. 6 Ethernet Connect your computer to a LAN port, using the included Ethernet cable. 7 WAN Connect to a Cable modem, xDSL modem, Fiber (PON) modem.
Chapter 3: Basic Installation You can configure the Mobile Broadband Wireless-N Router through the convenient and user-friendly interface of a web browser. Most popular operating systems such as Linux and Windows 98 / NT /2000 / XP / ME / 7 / Vista include a web browser as a standard application. PCs must have a properly installed Ethernet interface which connects to the router directly or through an external repeater hub.
Network Configuration Configuring a PC in Windows 7 1. Go to Start. Control Panel. Click on 2. Then click on Network and Internet. 3. When the Network and Sharing Center window pops up, select and click on Change adapter settings on the left window panel. 4. Select the Local Area Connection, and right click the icon to select Properties.
5. Select Internet Protocol Version 4 (TCP/IPv4) then click Properties. 6. In the TCP/IPv4 properties window, select the Obtain an IP address automatically and Obtain DNS Server address automatically radio buttons. Then click OK to exit the setting. 7. Click OK again in the Local Area Connection Properties window to apply the new configuration.
Configuring a PC in Windows Vista 1. Go to Start. Network. Click on 2. Then click on Network and Sharing Center at the top bar. 3. When the Network and Sharing Center window pops up, select and click on Manage network connections on the left window pane. 4. Select the Local Area Connection, and right click the icon to select Properties.
5. Select Internet Protocol Version 4 (TCP/IPv4) then click Properties. 6. In the TCP/IPv4 properties window, select the Obtain an IP address automatically and Obtain DNS Server address automatically radio buttons. Then click OK to exit the setting. 7. Click OK again in the Local Area Connection Properties window to apply the new configuration.
Configuring a PC in Windows XP 1. Go to Start. Click on Control Panel. 2. Then click on Network and Internet. 3. In the Local Area Connection Status window, click Properties. 4. Select Internet Protocol (TCP/IP) and click Properties. 5. Select the Obtain an IP address automatically and the Obtain DNS server address automatically radio buttons. 6. Click OK to finish the configuration.
Configuring a PC in Windows 2000 1. Go to Start / Settings / Control Panel. In the Control Panel, double-click on Network and Dial-up Connections. 2. Double-click Local Area Connection. 3. In the Local Area Connection Status window click Properties. 4. Select Internet Protocol (TCP/IP) and click Properties. 5. Select the Obtain an IP address automatically and the Obtain DNS server address automatically radio buttons. 6. Click OK to finish the configuration.
Configuring PC in Windows 98/Me 1. Go to Start / Settings / Control Panel. In the Control Panel, double-click on Network and choose the Configuration tab. 2. Select TCP/IP ->NE2000 Compatible, or the name of your Network Interface Card (NIC) in your PC. 3. Select the Obtain an IP address automatically radio button. 4. Then select the DNS Configuration tab. 5. Select the Disable DNS radio button and click OK to finish the configuration.
Configuring PC in Windows NT4.0 1. Go to Start / Settings / Control Panel. In the Control Panel, double-click on Network and choose the Protocols tab. 2. Select TCP/IP Protocol and click Properties. 3. Select the Obtain an IP address from a DHCP server radio button and click OK.
Factory Default Settings Before configuring the router, you need to know the following default settings. Web Interface: (Username and Password) Username: admin Password: admin The default username and password are “admin” and “admin” respectively. Attention If you ever forget the username/password to login to the router, you may press the RESET button up to 6 seconds then release it to restore the factory default settings.
Information from your ISP Before configuring this device, you have to check with your ISP (Internet Service Provider) what kind of services are provided, such as PPPoE, Obtain an IP Address Automatically, Fixed IP address. Gather the information as illustrated in the following table and keep it for reference. Username, Password, Service Name, and Domain Name PPPoE System (DNS) IP address (it can be automatically assigned by your ISP when you connect or be set manually).
Configuring with your Web Browser Open your web browser, enter the IP address of your router, which by default is 192.168.1.254, and click “Go”, a user name and password window prompt appears. Enter the user name and password that your administrator has set for you and select the Account Type, then click Login. When you are authorised, you will access to the router.The default username and password are “admin” and “admin” respectively for the Administrator account type.
Chapter 4: Basic Configuration Once you have logged on to your router via your web browser, you can begin to set it up according to your requirements.
Status Device Information Model Name: Provide a name for the router for identification purposes. System Up-Time: Record system up-time. Software Version: Firmware version. Port Status Port StatusΚ ΚUser can look up to see if they are connected to Ethernet, EWAN, 3G / 4G and Wireless. WAN Port: Name of the WAN connection. Protocol: PPPoE, Dynamic or Fixed. Operation: Current available operation. Connection: The current connection status. Netmask: WAN port IP subnet mask.
Quick Start Set Wireless configuration WLAN Service: Default setting is set to Enable. ESSID: The ESSID is the unique name of a wireless access point (AP) to be distinguished from another. For security purpose, change to a unique ID name to the AP which is already built-in to the router’s wireless interface. It is case sensitive and must not excess 32 characters. Make sure your wireless clients have exactly the ESSID as the device, in order to get connected to your network.
WAN EWAN 3G / 4G-LTE (The router also support 4G-LTE network, and user must tell the provider the exact 4G-LTE service you want for the 4G-LTE router) APN: An APN is similar to a URL on the WWW, it is what the unit makes a GPRS / UMTS / LTE call. The service provider is able to attach anything to an APN to create a data connection. Requirements for APN assignment varies between different service providers.
systems as a password to gain access, and authentication. In mobile phones a PIN code locks the SIM card until you enter the correct code. If you enter the PIN code incorrectly into the phone 3 times in a row, then the SIM card will be blocked and a PUK code will be required from your network / service provider to unlock it.
Security Parameters WPA Pre-Shared Key WPA Shared Key: The key for network authentication. The input format is in character style and the key size should be in the range between 8 and 63 characters (here the default is the router or CPE’s MAC address in uppercase). Group Key Renewal: The period of renewal time for changing the security key between wireless client and Access Point (AP). This process is done automatically. WPA2 Pre-Shared Key WPA Shared Key: The key for network authentication.
WEP WEP Authentication: To prevent unauthorized wireless stations from accessing data transmitted over the network, the router offers secure data encryption, known as WEP. If you require high security for transmissions, there are three options to select from: Open System, Share key or Both. Default Used WEP Key: Select the encryption key ID; please refer to Key (1~4) below.
Chapter 5: Advanced Configuration Once you have logged on to your router via your web browser, you can begin to set it up according to your requirements.
Status Device Information Model Name: Display the model name. Host Name: Provide a name for the router for identification purposes. Host Name lets you change the router name. Click this link to turn to Device Management configuration. System Up-Time: Record system up-time. Current time: Set the current time. See the Time Zone section for more information. Click this link to turn to Time Zone configuration. Software Version: Firmware version. MAC Address: The LAN MAC address.
Status: The current status of the 3G /4G-LTE SIM card. Click this link to configure 3G (4G-LTE). For detail, turn to 3G configuration page for help. Signal Strength: The signal strength bar indicates the current 3G(4G-LTE) signal strength. Network Name: The network name that the device is connected to. Card Name: The name of the 3G /4G-LTE SIM card. Card Firmware: The current firmware of the 3G / 4G-LTE card. Card IMEI: The unique identification number that is used to identify the 3G / 4G-LTE card.
IP Address: It is IP Address of internal host that join this network. MAC Address: The MAC address of internal host. Interface: indicates which side the IP addresses locate on. WAN means the corresponding IP locates on WAN side. Static ARP: The state for ARP. “No” for dynamically-generated ARP table entries. “Yes” for static ARP table entries added by the user. DHCP Table IP Address: The current corresponding DHCP-assigned dynamic IP address of the device.
Firewall Log Firewall Log displays log information of any unexpected action with your firewall settings. This page displays the router’s Firewall Log entries. The log shows log entries when you have enabled Intrusion Detection or Block WAN PING in the Configuration - Firewall section of the interface. Please see the Firewall section of this manual for more details on how to enable Firewall logging. UPnP Portmap The section lists all port-mapping established using UPnP (Universal Plug and Play).
Name: the name of this UPnP mapping. Protocol: the protocol used by this mapping. External Port: the external service port the internal port mapped to. Internal Port: the internal service port. IP Address: the IP Address of the host in LAN.
Quick Start Step 1: Enable and Select the appropriate Time Zone, then click Continue to go on to next step. You can turn Time Zone to understand more. 3G Step 1: Select the connection mode: 3G. Then click Continue. If you want directly go to wireless setting, please click Jump to Wireless setting and go to step 3.
Step 2: WAN have been successfully configured, and move on to wireless settings. Step 3: Set Wireless Configuration. WLAN Service: Default setting is set to Enable. ESSID: The ESSID is the unique name of a wireless access point (AP) to be distinguished from another. For security propose, change to a unique ID name to the AP which is already built-in to the router’s wireless interface. It is case sensitive and must not excess 32 characters.
WPA Shared Key: The key for network authentication. The input format is in character style and key size should be in the range between 8 and 63 characters(here the default is the router or CPE’s MAC address in uppercase). WPA/WPA2 Pre-Shared Key WAP Shared Key: The key for network authentication. The input format is in character style and key size should be in the range between 8 and 63 characters (here the default is the router or CPE’s MAC address in uppercase).
Step 5: Success. EWAN Step 1: Select the connection mode:EWAN. Then click Continue. Here take EWAN for example. If you want directly go to wireless setting, please click Jump to Wireless setting and go to step 4. Step 2: Select the Protocol. Protocol: The current protocol in the device. Click on Continue to choose the Protocol to connect with EWAN. Obtain an IP Address Automatically When connecting to the ISP, Mobile Broadband Wireless-N Router also functions as a DHCP client.
If connection is successful the following image will be shown. Fixed IP Address Select this option to set static IP information. You will need to enter in the Connection type, IP address, Netmask, and gateway address, provided to you by your ISP. Each IP address entered in the fields must be in the appropriate IP form, which are four IP octets separated by a dot (x.x.x.x). The Router will not accept the IP address if it is not in this format.
PPPoE PPPoE (PPP over Ethernet) provides access control in a manner similar to dial-up services using PPP. Protocol: The current ATM protocol in the device Username: Enter the username provided by your ISP. You can input up to 128 alphanumeric characters (case sensitive). This is in the format of “username@ispname” instead of simply “username”. Password: Enter the password provided by your ISP. You can input up to 128 alphanumeric characters (case sensitive). Service Name: Enter a name for this connection.
Step 3: In the previous step, press Next to Wireless to Set Wireless configuration. Turn to Quick Start > 3G > Wireless setting for more. Step 4: Saving configuration. Step 5: Success.
Configuration Click this item to access the following sub-items that configure the 3G router: LAN, WAN, System, Firewall, QoS, Virtual Server, Wake on LAN, Time Schedule and Advanced. These functions are described in the following sections. LAN (Local Area Network) A Local Area Network (LAN) is a shared communication system to which many computers are attached and is limited to the immediate area, usually the same building or floor of a building.
Wireless Parameters WLAN Service: Default setting is set to Enable. Mode: The default setting is Wireless G + N (Mixed mode). If you do not know or have both 11g and 11n devices in your network, then keep the default in mixed mode. From the drop-down manual, you can select Wireless – G if you have only 11g card. If you have only 11b card, then select Wireless – B. If you have only 11n card, then select Wireless – N. Number of Active SSID: Number of SSID you can choose. SSID No.: The SSID you choose.
scanned, with some security settings, you will join this wireless network. Regulation Domain: There are seven Regulation Domains for you to choose from, including North America (N.America), Europe, France, etc. The Channel ID will be different based on this setting. Channel ID: Select the ID channel that you would like to use. Channel Wdith: Select either 20 MHz or 20/40 MHz for the channel bandwidth. The higher the bandwidth the better the performance will be.
SSID No.: Choose the SSID you want to set. Security Mode: There are five security modes for you to choose. WPA Pre-Shared Key WPA Algorithms: TKIP (Temporal Key Integrity Protocol) / AES (Advanced Encryption Standard) utilizes a stronger encryption method and incorporates Message Integrity Code (MIC) to provide protection against hackers. WPA Shared Key: The key for network authentication. The input format is in character style and key size should be in the range between 8 and 63 characters.
WPA Algorithms: TKIP (Temporal Key Integrity Protocol) / AES (Advanced Encryption Standard) utilizes a stronger encryption method and incorporates Message Integrity Code (MIC) to provide protection against hackers. WPA Shared Key: The key for network authentication. The input format is in character style and key size should be in the range between 8 and 63 characters. Group Key Renewal: The period of renewal time for changing the security key automatically between wireless client and Access Point (AP).
WEP Authentication: To prevent unauthorized wireless stations from accessing data transmitted over the network, the router offers secure data encryption, known as WEP. If you require high security for transmissions, there are three options to select from: Open System, Share key or Both. Default Used WEP Key: Select the encryption key ID; please refer to Key (1~4) below. Passphrase: This is used to generate WEP keys automatically based upon the input string and a pre-defined algorithm in WEP64 or WEP128.
2. Enter the Enrollee’s PIN number and then press Start. 3. Launch the wireless client’s WPS utility (eg. Ralink Utility). Set the Configure Mode as Enrollee, press the WPS button on the top bar, select the AP (eg. wlan-ap) from the WPS AP List column.Then press the PIN button located on the middle left of the page to run the scan. 4. The client’s SSID and security setting will now be configured to match the SSID and security setting of the registrar.
PIN Method: Configure AP as Enrollee 1. In the WPS configuration page, change the Role to Enrollee. Then press Start. 2. Jot down the WPS PIN (e.g. 25879810). 3. Launch the wireless client’s WPS utility (e.g. Ralink Utility). Set the Config Mode as Registrar. Enter the PIN number in the PIN Code column then choose the correct AP (eg. wlan-ap) from the WPS AP List section before pressing the PIN button to run the scan.
4. The router’s (AP’s) SSID and security setting will now be configured to match the SSID and security setting of the registrar.
5. Now to make sure that the setup is correctly done, cross check to see if the SSID and the security setting of the registrar setting match with the parameters found on both Wireless Configuration and Wireless Security Configuration page.
The parameters on both Wireless Configuration and Wireless Security Configuration page are as follows: PBC Method: 1. Press the PBC button of the AP. 2. Launch the wireless client’s WPS Utility (eg. Ralink Utility). Set the Config Mode as Enrollee. Then press the WPS button and choose the correct AP (eg. wlan-ap) from the WPS AP List section before pressing the PBC button to run the scan.
3. When the PBC button is pushed, a wireless communication will be established between your router and the PC. The client’s SSID and security setting will now be configured to match the SSID and security setting of the router.
Wi-Fi Network Setup with Windows Vista WCN: 1. Jot down the AP PIN from the Web (eg. 25879810). 2. Access the Wireless configuration of the web GUI. Set the WPS State to Unconfigured then click Apply.
3. In your Vista operating system, access the Control Panel page, then select Network and Internet > View Network Computers and Devices. Double click on the router icon and enter the AP PIN in the column provided then press Next.
4. Enter the AP SSID then click Next. 5. Enter the passphrase then click Next. 6.
built-in WCN feature in Windows Vista.
DHCP Server You can disable or enable the DHCP (Dynamic Host Configuration Protocol) server or enable the router’s DHCP relay functions. The DHCP protocol allows your router to dynamically assign IP addresses to PCs on your network if they are configured to obtain IP addresses automatically. DHCP Server Mode: Disable To disable the router’s DHCP Server, check Disabled and then click Apply.
network administrator or ISP. Click Apply to enable this function.
WAN (Wide Area Network) A WAN (Wide Area Network) is an outside connection to another network or the Internet. There are two items within the WAN section: WAN interface and WAN Profile. WAN Interface (EWAN) Connect Mode: Select the main port from the drop-down menu. Click Apply to confirm the change. WAN Interface (3G) Connect Mode: Select the main port from the drop-down menu. Click Apply to confirm the change.
Connect Mode: Select the Dual WAN from the drop-down menu. Main WAN: Choose EWAN or 3G as main WAN. Click the link to go to WAN Profile page to configure its parameters. Click the link beside it to configure the Main WAN connection. Turn to WAN profile in the following part for help. Backup WAN: Choose the left as backup WAN. Click the link to go to WAN Profile page to configure its parameters. Click the link beside it to configure the backup WAN.
WAN Profile Main Port – EWAN Mobile Broadband Wireless-N Router offers a WAN port to connect to Cable Modems and fiber optic lines. This alternative, yet faster method to connect to the internet will provide users with more flexibility to get online. Obtain an IP Address Automatically (EWAN) When connecting to the ISP, Mobile Broadband Wireless-N Router also functions as a DHCP client.
PPPoE (EWAN) PPPoE (PPP over Ethernet) provides access control in a manner similar to dial-up services using PPP. Username: Enter the username provided by your ISP. You can input up to 128 alphanumeric characters (case sensitive). This is in the format of “username@ispname” instead of simply “username”. Password: Enter the password provided by your ISP. You can input up to 128 alphanumeric characters (case sensitive) Service Name: This item is for identification purposes.
Fixed IP Address (EWAN) Select this option to set static IP information. You will need to enter in the Connection type, IP address, netmask, and gateway address, provided to you by your ISP. Each IP address entered in the fields must be in the appropriate IP form, which is four IP octets separated by a dot (x.x.x.x). The Router will not accept the IP address if it is not in this format. Line Speed: Set the downstream and upstream of your connection in kilobytes per second.
Main Port - 3G The router allows you to insert a 3G/4G-LTE S I M card into to the built-in SIM slot, enabling you to use a, UMTS, GSM, or LTE Internet connection, makes downstream rates of to 14.4 Mbps*. Usage Allowance: enable when you want to control 3G usage. Click this link to enter 3G Usage Allowance to configure. ISP Mode: Choose 3G / 4G-LTE service provider. TEL No.: The dial string to make a GPRS / 3G user internetworking call. It may be provided by your mobile service provider.
MTU: Maximum Transmission Unit. The size of the largest datagram (excluding media-specific headers) that IP will attempt to send through the interface. PIN: PIN stands for Personal Identification Number. A PIN code is a numeric value used in certain systems as a password to gain access, and authentication. In mobile phones a PIN code locks the SIM card until you enter the correct code.
In order to query online time or volume used, you can set the following options. Mode: Two methods are provided, that is, Volume-based and Time-based. Volume-based: If choosing Volume-based, you can view the volume you have used. Only Download: Only make statistics of Download Traffic. Only Upload: Only make statistics of Upload Traffic. Download and Upload: Make statistics of both Download and Upload Traffic. Time-based: If choosing Time-based, you can view the online hours you have used.
System There are five items within the System section: Time Zone, Firmware Upgrade, Backup/Restore, Restart, User Management and Mail Alert. Time Zone The router does not have a real time clock on board; instead, it uses the Simple Network Time Protocol (SNTP) to get the current time from an SNTP server outside your network. Choose your local time zone, click Enable and click the Apply button.
Firmware Upgrade Your router’s “firmware” is the software that allows it to operate and provides all its functionality. Think of your router as a dedicated computer, and the firmware as the software it runs. Over time this software may be improved and modified. Your router allows you to upgrade the software it runs to take advantage of these changes. Clicking on Browse allows you to select the new firmware image file you have downloaded to your PC.
Select the correct file used for upgrade, and press START. Backup / Restore These functions allow you to save and backup your router’s current settings to a file on your PC, or to restore a previously saved backup. This is useful if you wish to experiment with different settings, knowing that you have a backup handy in the case of any mistakes. It is advisable to backup your router’s settings before making any significant changes to your router’s configuration.
Restart Router Click Restart with option Current Settings to reboot your router and save the current configuration to device. If you wish to restart the router using the factory default settings (for example, after a firmware upgrade or if you have saved an incorrect configuration), select Factory Default Settings to reset to factory default settings. User Management In order to prevent unauthorized access to your router’s configuration interface, it requires all users to login with a password.
SMTP Server: Enter the SMTP server that you would like to use for sending emails. Username: Enter the username of your email account to be used by the SMTP server. Password: Enter the password of your email account. Sender’s Email: Enter your email address. Recipient’s Email (Failover / Failback): Enter the email address that will receive the alert message once a computer / network server failover occurs.
Firewall and Access Control Your router includes a full SPI (Stateful Packet Inspection) firewall for controlling Internet access from your LAN, as well as helping to prevent attacks from hackers. In addition to this, when using NAT (Network Address Translation) the router acts as a “natural” Internet firewall, since all PCs on your LAN use private IP addresses that cannot be directly accessed from the Internet. See the WAN configuration section for more details on NAT.
URL Filter: Blocks PCs on your local network from unwanted websites. A detailed explanation of each of the following five items appears in the Firewall section below: Packet Filter, MAC Address Filter, Intrusion detection, Block WAN PING and URL Filter. Packet Filter Packet filtering enables you to configure your router to block specified internal/external users (IP address) from Internet access, or you can disable specific service requests (Port number) to /from Internet.
Log: Choose “log” if you wish to generate logs when the filer rule is applied to a packet. Add: Click this button to add a new packet filter rule and the added rule will appear at the bottom table. Edit: Check the Rule No. you wish to edit, and then click “Edit”. Delete: Check the Rule No. you wish to delete, and then click “Delete”.
• Disable: to disable the MAC filter function. • Allow: to enable the MAC filter function and allow the host of the following set MAC addresses to access. • Block: to enable the MAC filter function and block the host of the following set MAC addresses to access. MAC Address: Enter the MAC addresses you wish to manage. Time Schedule: It is self-defined time period. You may specify a time schedule for your prioritization policy. For setup and detail, refer to Time Schedule section.
WinNuke TCP Port 135, 137~139, Src IP Flag: URG DoS Yes Yes Smurf ICMP type 8 Dst IP Des IP is broadcast Victim Protection Yes Yes Land attack SrcIP = DstIP Yes Yes Echo/CharGen Scan UDP Echo Port and CharGen Port Yes Yes Echo Scan UDP Dst Port = Src IP Echo(7) Scan Yes Yes CharGen Scan UDP Dst Port = Src IP CharGen(19) Scan Yes Yes X’mas Tree Scan TCP Flag: X’mas Src IP Scan Yes Yes IMAP SYN/FIN Scan TCP Flag: SYN/FIN DstPort: IMAP(143) Src IP SrcPort: 0 or 65535 Scan Y
URL Filter URL (Uniform Resource Locator – e.g. an address in the form of http://www.example.com ) filter rules allow you to prevent users on your network from accessing particular websites from their URL. There are no pre-defined URL filter rules; you can add filter rules to meet your requirements. Keywords Filtering Allows blocking by specific keywords within a particular URL rather than having to specify a complete URL (e.g. to block any image called “advertisement.gif”).
to block traffic to www.google.com.au, enter “www.google” or “www.google.com” Restrict URL Features This function enhances the restriction to your URL rules. Block Java Applet: Blocks Web content which includes the Java Applet to prevent someone who wants to damage your system via the standard HTTP protocol. Block ActiveX: Blocks ActiveX Block Cookies: Blocks Cookies Block Proxy: Blocks Proxy Except IP Address Time Schedule: It is self-defined time period.
QoS (Quality of Service) Quality of Service Introduction If you’ve ever found your ‘net’ speed has slowed to a crawl because another family member is using a P2P file sharing program, you’ll understand why the Quality of Service features in the routers is such a breakthrough for home users and office users.
from LAN to WAN or WAN to LAN.) Protocol: The Protocol will be controlled. For GRE protocol, there is no need to specify the IP addresses or Application ports in this page. For other protocols, at least one value shall be given. ANY: No protocol type is specified. TCP UDP ICMP GRE DSCP Marking: Differentiated Services Code Point (DSCP), it is the first 6 bits in the ToS byte. DSCP Marking allows users to classify traffic based on DSCP value and send packets to next Router.
Ratio: Assign the data ratio for this policy to be controlled. For examples, we want to only allow 20% of the total data transfer rate for the LAN-to-WAN direction to be used for FTP server. Then we can specify here with data ratio = 20. Priority: Specify the priority for the bandwidth that is not used. For examples, you may specify two different QoS policies for different applications.
For Mail Sending Here we guarantee 30% of the traffic for Mail application. thus, 20% of LAN to WAN (upsteam) traffic is reserved for other uses and those applications’ bandwidths are guaranteed. For downstream traffic bandwidth, just the direction changes and the configuration is similar. That’s just a simple example for QoS application, for more please refer to FAE.
Virtual Server In TCP and UDP networks a port is a 16-bit number used to identify which application program (usually a server) incoming connections should be delivered to. Some ports have numbers that are pre-assigned to them by the IANA (the Internet Assigned Numbers Authority), and these are referred to as “well-known ports”. Servers follow the well-known port assignments so clients can locate them. If you wish to run a server on your network that can be accessed from the WAN (i.e.
Port Mapping Application: Select the service you wish to configure. Protocol: Automatic when you choose Application from list-box or select a protocol type which you want. External Port & Internal Port: Enter the public port number & range you wish to configure. Internal IP Address: Enter the IP address of a specific internal server to which requests from the specified port is forwarded. Add: Click to add a new virtual server rule. Click again and the next figure appears. Edit: Check the Rule No.
protocol is determined by the particular application. Most applications use TCP or UDP, however you can specify other protocols using the drop-down Protocol menu. Setting the protocol to “all” causes all incoming connection attempts using all protocols on all port numbers to be forwarded to the specified IP address. DMZ The DMZ Host is a local computer exposed to the Internet.
3. Click Delete to delete the one which you want to remove from the except list. Using port mapping does have security implications, since outside users are able to connect to PCs on your network.
Wake on LAN Wake on LAN (WOL, sometimes WoL) is an Ethernet computer networking standard that allows a computer to be turned on or woken up remotely by a network message. Select: Select MAC address of the computer that you want to wake up or turn on remotely. Add: After selecting, click Add then you can perform the Wake-up action. Edit/Delete: Click to edit or delete the selected MAC address. Ready: “Yes“ indicating the remote computer is ready for your waking up.
Time Schedule The Time Schedule supports up to 16 time slots which helps you to manage your Internet connection. In each time profile, you may schedule specific day(s) i.e. Monday through Sunday to restrict or allowing the usage of the Internet by users or applications. This Time Schedule correlates closely with router’s time, since router does not have a real time clock on board; it uses the Simple Network Time Protocol (SNTP) to get the current time from an SNTP server from the Internet.
Advanced Configuration options within the Advanced section are for users who wish to take advantage of the more advanced features of the router. Users who do not understand the features should not attempt to reconfigure their router, unless advised to do so by support staff. There are seven items within the Advanced section: Static Route, Static ARP, Dynamic DNS, Device Management, SIP_ALG, IGMP, SNMP Access Control, TR-069 client and Remote Access.
does not assign you a static IP address you can still use a domain name. This is especially useful for hosting servers via your 3G 4G-LTE connection, so that anyone wishing to connect to you may use your domain name, rather than having to use your dynamic IP address, which changes from time to time. This dynamic IP address is the WAN IP address of the router, which is assigned to you by your ISP.
Embedded Web Server HTTP Port: The port number of the router’s embedded web server (for web-based configuration uses. The default value is the standard HTTP port, 80. You may specify an alternative if, for example, you are running a web server on a PC within your LAN. For Example: User A changes HTTP port number to 100, specifies their own IP address of 192.168.1.55, and sets the logout time to be 100 minutes. The router only allows User A access from the IP address 192.168.1.
Components selection box. Step 4: Click OK to go back to the Add/Remove Programs Properties window. Click Next. Step 5: Restart the computer when prompted. Follow the steps below to install the UPnP in Windows XP. Step 1: Click Start and Control Panel. Step 2: Double-click Network Connections. Step 3: In the Network Connections window, click Advanced in the main menu and select Optional Networking Components …. The Windows Optional Networking Components Wizard window displays.
Step 5: In the Networking Services window, select the Universal Plug and Play check box. Step 6: Click OK to go back to the Windows Optional Networking Component Wizard window and click Next. Auto-discover Your UPnP-enabled Network Device Step 1: Click start and Control Panel. Double-click Network Connections. An icon displays under Internet Gateway. Step 2: Right-click the icon and select Properties.
Step 3: In the Internet Connection Properties window, click Settings to see the port mappings that were automatically created. Step 4: You may edit or delete the port mappings or click Add to manually add port mappings.
Step 5: Select Show icon in notification area when connected option and click OK. An icon displays in the system tray Step 6: Double-click on the icon to display your current Internet connection status.
Router without first finding out the IP address of the router. This helps if you do not know the router’s IP address. Follow the steps below to access web configuration. Step 1: Click Start and then Control Panel. Step 2: Double-click Network Connections. Step 3: Select My Network Places under Other Places. Step 4: An icon describing each UPnP-enabled device shows under Local Network. Step 5: Right-click on the icon of your Mobile Broadband Wireless-N Router and select Invoke.
SIP_ALG Select Enable to activate SIP ALG feature or Disabled to disable this feature. The Session Initiation Protocol (SIP) is an IETF-defined signaling protocol, widely used for controlling multimedia communication sessions such voice and video calls over Internet protocol (IP). The protocol can be used for creating, modifying and terminating two-party (unicast) or multiparty (multicast) sessions consisting of one or several media streams. It is a text-based Application Layer protocol.
SNMP Access Control Software on a PC within the LAN is required in order to utilize this function - Simple Network Management Protocol. SNMP V1 and V2 Read Community: Specify a name to be identified as the Read Community, and an IP address. This community string will be checked against the string entered in the configuration file. Once the string name is matched, user obtains this IP address will be able to view the data.
TR-069 Client TR069, (short for Technical Report 069) is a DSL Forum (which was later renamed as Broadband Forum) technical specification entitled CPE WAN Management Protocol (CWMP). It defines an application layer protocol for remote management of end-user devices. It defines an application layer protocol for remote management of end-user devices. As a bidirectional SOAP/HTTP based protocol it can provides the communication between customer premises equipment (CPE) and Auto Configuration Server (ACS).
Duration: Set how many minutes to allow management access from remote side. Zero means always on. Allowed Access IP Address Range Valid: Select Valid to allow remote management from these IP ranges. IP Address Range: Specify what IP address to be allowed to access device from remote side. Clink Add to insert management IP address list.
Be aware that the router is restricted to only one PC accessing the configuration web pages at a time. Once a PC has logged into the web interface, other PCs cannot get access until the current PC has logged out of the web interface. If the previous PC forgets to logout, the second PC can access the page after a user-defined period, by default 3 minutes. You can modify this value using the Advanced - Device Management section of the web interface.
Chapter 6: Troubleshooting If your Router is not functioning properly, you can refer first to this chapter for simple troubleshooting before contacting your service provider support. This can save you time and effort but if symptoms persist, consult your service provider. Problems starting up the router Problem Corrective Action None of the LEDs Check the connection between the adapter and the router. If the error are on when you persists, you may have a hardware problem.
