User's Manual

4
5
6
2
3
WXM29
The XLR Microphone Wireless System adopts UHF frequency band
transmission, which has the characteristics of long transmission distance,
strong anti-interference ability, low delay and clear sound quality. Compatible
with a variety of pickups. The working status is intuitive, and easy to use.
Note: Please read and follow all warnings carefully before use, and keep this
manual for subsequent use.
microphone music input switching
Transmitter
Connect microphoneConnect microp hone
48V power supply.
Up for audio input; down for mic input
Green light when powered on
Type-c charging port, input voltage DC5 V 1A
Type-c charging port, input voltage DC5 V 1A
When connecting the Condenser
microphone, you need to press twice, the n
long press for 10 seconds to 48V mode
(48V will be displayed on the screen)
(1)Hold to turn on;long press to turn off
(2)Change frequency:short press tw ice with
powered on. 25 frequencies in total.
4
5
2
3
4
5
2
3
Input port to connect amplifier
Display connection, battery life and f requency
Hold to turn on;Long press to turn off
Red
Green
Blue
Low power
Volume
Battery life
Audio equipment with XLR port can be connected to this product, including
mixers, multimedia speakers, power amplifiers, etc.
Mixing console
PA
Trans mitter can not
be turned on
Receiver can not be
turned on
No sound
Small sound
Intermittent sound
Howling, screaming
1
(1)Charge first, then check whether the t ransmitter charging indicator ligh t is on.
(2)Press and hold the power switch for 2 sec onds to power on, short p ress
cannot power on.
(1)Charge first, then check whether the t ransmitter charging indicator ligh t is on.
(2)Press and hold the power switch for 2 sec onds to power on, short p ress
cannot power on.
(1)Check whether the volume of the micro phone and the audio dev ice has
(2)Check whether the transmitter and r eceiver are successfully connected ;
(3)The amplifier which connect the rece iver may need to set the in put mode,
been turned on;
the microphone information will be dis played if the connect ion is successful.
please refer to the manual of the amplifier f or setting;
(1)Check whether the switch button of th e transmitter is in the appropriate
(2)Tu rn up the volume of the out put device.
position. If the transmitter is connec ted to the microphone input, it should be
adjusted to the microphone position,
(1)Shorten the distance between the tr ansmitter and the receiver, the visual
(2)Change frequency;
distance does not exceed 50M, and the tran smission distance w ill be shortened
when there are obstacles in the middle;
(1)Reduce the volume of the amplifier or mi crophone;
(2)Do not place the microphone too close t o the speaker.
2
3
4
5
6
Receiving frequency: U Band Frequency stability: <0.002%
Sensitivity: 2mV Interference frequency ratio > 90dB
Image interference ratio: >88dB Signal to noise ratio: >95dB
Audio output: 800mV-1.4V
Working range: Standard condit ions 30 to 50 m
Receive channel: 1
Supply Voltage: DC 5V
Antenna: universal antenna
Carrier frequency: U Band Frequency stability: <0.002%
Trans mit power: 10mW
Current consumption: <25mA
Harmonic: <Main wave 40dB
Standard: Fixed frequency
Battery: lithium battery
Antenna: built-in
Dynamic Range: >95dB
System distortion(<1%，1K Hertz modul ation)
Frequency response: 50Hz-18KHz(+ 3dB)
1X Transmitter
1X Receiver
1X XLR to 6.35mm adapter
1X charging cable
1X User Manual