Instruction manual T162A SERIES Smart Toilet
※ Please read this manual thoroughly before using the product. ※ Please do not hesitate to contact us if you have any questions in the installation or usage. ※ Please keep this manual available for future maintenance or reference.
Contents Safety precautions........................................................................ 1 Components.................................................................................. 4 Specification................................................................................. 5 Functions introduction ................................................................ 6 Parts name .................................................................................... 7 Product drawing ...............
Safety precautions To prevent damage to the unit and possible injury to users, please follow the safety warnings. Please be sure to carefully read through the user's manual before installation. Keep the user's manual after installation to refer to for troubleshooting advice. Symbols and meanings WARNING Could result in serious injury or death. The following symbols are used to indicate important safety precautions when using the product. Prohibited. Pay close attention; caution.
WARNING Stop using the product immediately if you observe: Smoke Unusual sound or odor Leakage, breakage or other damage Blocked toilet pan Continued use under these conditions could cause electrical shock, injury, or water leakage. Do not clean the smart bidet with heavy chemical cleaning agents such as paint thinner, gasoline, putty powder, nylon brush, etc. Otherwise, it could trigger a chemical reaction, cause leakage, damage to the product or personal injury.
WARNING Make sure the product is installed in a well-ventilated area. Excess humidity and moisture could cause electrical shock or fire. Disconnect the power supply before removing this product from the toilet to prevent electrical shock or fire. To prevent electrical shock or fire, disconnect the power supply before cleaning the product and do not apply water directly to it. Do no expose the product to direct sunlight.
Components SMART TOILET REMOTE CONTROL REMOTE CONTROL HOLDER USER'S MANUAL User's Manual REMOTE EXPANSION SCREW GROUP (EACH 2pcs) DOUBLE-FACED ADHESIVE TAPE SEALING RING INLET VALVE FLOW RESTRICTOR -4-
Specifications Rated voltage 100-130V~ Power cord length Water volume Cleaning Rear wash Bidet wash Swing Massage Water volume /nozzle position Water temperature range Drying Seat Water supply temperature Dimension Oscillating cleaning forward and backward Two options: press once for interval cleaning, press twice for continuous cleaning 3 levels adjustment About 68°F-107°F(4 levels adjustment) Temperature limit circuit, thermostat, thermal fuse Safety device Bimetallic thermostat, thermal fu
Functions introduction Washing function Rear wash Cleaning posterior. Bidet wash Cleaning feminine body. Water flow adjustment Adjust water flow rate. Spray position adjustment Massage cleaning Swing cleaning Comfort functions Adjust nozzle position to expand cleaning scope. The nozzle spray variable intensity water column to massage. Swing back and forth to cleansing most area. Seat heated Heat seat and keep temperature. Temperature adjustment Adjust temperature of water,seat or drying.
Parts name Lid Seat Rear wash hole Bidet wash hole Power-off flush connector Drying baffle Nozzle baffle Knob Nozzle Ceramic toilet sor sen Power indicator Foot sensing Seat temp status indicator Flushing status indicator Water temp indicator Seat temp indicator Water temp indicator Seat temp indicator -7-
Product drawings About 465mm(18.3 in) About 400mm(15.7 in) About 680mm( 26.8 in) Power and water connection tip Connect to grounded outlet Caution electricity! GFCI outlet ※ If the power cord is not long enough, please do not use a extension cord. ※ Only for reference. Bathroom sizes and configurations may vary.
Installation precaution (1)Don’t install our product in the room with more than 90%RH humidity (relative humidity). It is suggested to separate dry space from moist one, such as installing shower rooms or shower curtains. (2)Only the specified power supply can be used. (Other power sources may cause product failure or damage). (3)Please do not supply water or power before finishing installation. (4)Please use wires and waterproof sockets suitable for the power of this product.
Product installation 1. Install the water inlet valve Clean the ground and dry the water before installation. Mark the central lines of the draining outlet, and install the inlet valve on the wall. Connect to grounded outlet Caution electric shock! GFCI outlet 150mm(5.9 in) >500mm(19.7 in) (1 mm 0 30 1.8 in) Drain outlet 2. Mark the curve of ceramics 305 mm (12. 0 in ) center mark line Align the drain hole of ceramic with the central line.
Product installation 3.Toilet installation(Method 1) ① Sealing ring installation Gently tilt the toilet sideways until it rests on the side surface. Install the sealing ring evenly along the outlet, and the small end of the sealing ring facing the toilet. Glue the edge of toilet bottom with glass cement, place the toilet base along the outline and position the toilet base.
Product installation 4.Toilet installation(Method 2) ① Remove the bidet seat Remove the fixing screws of the toilet; remove the connecting pipes and wires of the toilet, separate the bidet seat from the toilet. Decoration panel Screw Washer Fixed hole ② Sealing ring installation Place the sealing ring on to the flange.
Product installation ③ Ceramic installation Glue the edge of toilet bottom with glass cement. Line up the toilet base over the flage screws. Place the toilet base and secure the flange bolts. Glue the edge of toilet bottom with glass cement, place the toilet base along the outline and position the toilet base. ④ Bidet seat installation Attach the connecting pipes and wires of the toilet, adjust the bidet seat to match the toilet, use the screws to fix the bidet seat on the toilet.
Product installation 5. Connection of water inlet valve Connect the water inlet braided pipe to the water inlet angle valve; if the water pressure is high, you can install a flow restrictor or adjust the position of the angle valve to achieve the best flushing effect. NOTE: Clean the floor and tools, do not use the toilet immediately, it takes 48 hours to cure and keep the toilet dry. G1/2 Fow restrictor NOTE: If the water pressure is less than 0.24Mpa(static pressure),remove the flow restrictor .
Instructions for remote control Installation Method 1: ① Install the remote control fixing panel with a magnet on the remote control fixed seat and lock tightly. Note: Pay attention to the polarity when installing the magnet. Place the larger side of the magnet hole outside the fixed panel and enclose the small hole surface inside the fixed panel, as shown in the below figure 1. ② Put the double sided tape on the remote control fixed seat. ③ Clean dust, grease, water droplets on the walls and wipe them clean.
Remote control panel overview Signal window Signal light Rear Stop REAR Minus STOP BIDET Bidet Flush Plus FLUSH Water temp Flow FLOW Seat temp SEAT Dry DRY TEMP POSITION Nozzle position Massage MASSAGE SWING Swing User 1 USER1 USER2 User 2 Lid open/close ECO Seat open/close Remote control alignment: After the product is connected to the power supply, the remote control alignment operation can be carried out within 1 minute from the buzzer call.
STOP Using instructions Press the button, all functions off. REAR Press the button, rear spray function turns on, auto off after 2 mins or off by pressing the stop button. Function will stop if user leaves. BIDET Press the button, bidet/front spray function turns on, auto off after 2 mins or off by pressing the stop button. Function will stop if user leaves. FLOW ADJUSTMENT FLOW Under rear/bidet wash mode, the water flow is settled on normal level( initial level is in the medium ).
Flush DRY USER1 USER2 FLUSH Using instructions Press "flush" button to activate flushing. DRY Press the button, dry function on after sounded.(Default level is 3.Press plus button will increase warm dry temp.Press minus button will decrease warm dry temp,total 5 levels. and corresponding indicator will on under different level)Auto off after 2 mins or off by pressing the stop button. Function will stop if user leaves.
Knob function description Knob function description No need to reset the stepless knob after use Backward Press ● ● ● ● ● ● ● ● ● Forward Sitting Bidet wash: Knob forward, spray bar extend, bidet wash works about 2 minutes. Rear wash: Knob backward, spray bar extend, rear wash works about 2 minutes. Nozzle position: Under bidet/rear wash,knob forward or backward to adjust nozzle position. Stop: Under bidet/rear wash,press the knob to stop current working function.
Cleaning Maintenance and cleaning of lid and seat. 1. Disconnect the power, turn off tee valve. 2. In case of using a mixture of washing agent and water as well as any available solution for seat cleaning, use soft and wet sponge or cloth to clean the seat. Use a soft towel to make the seat dry, or let it dry naturally. ※The product is an electric appliance. Be careful not to allow water to get inside or leave detergent in the gap between the top unit and the bowl unit.
Measures for special cases When the toilet can't be flushed automatically due to power interruption. USB TPYE-C When the power is off, connect to the USB TPYE-C with a power bank to achieve the power off flushing. When the toilet can't be flushed automatically due to water interruption. ① Flush away the sewage in the toilet by a special basin for taking in water. ② After water flushing, water level is lowered and water is added to avoid stink.
Phenomenon The product out of work Rear cleaning Bidet cleaning Dry Trouble shooting Reasons Measures Whether the power supply is plugged in. Insert the plug or detect the power socket. The leakage protector is disconnected. Insert the plug the power socket, press reset button on the plug. Power failure. Wait until the power is restored. Has a water failure occurred? Press the “stop”button and wait until the water The wand extends but water does not come failure is over. out.
Phenomenon The dry temperature is not enough. Trouble shooting Reasons Lower dry temperature is set. Measures Use the remote control to adjust dry temperature. The toilet does not flush Water is not available from the water supply. Use a bucket full of water to flush. when the button is pressed. Check the tee valve. The water supply valve is not fully open. The water supply valve is not fully open. Check the tee valve. Clean the filter. The water filter is clogged.
Product Maintenance Service Sheet The selling store Province Maintenance content Product code City Purchase date Dealer ( signature ): Free maintain regulation: 1、Free maintenance is provided when you use it properly in accordance with instructions and under warranty. 2、Please contact the dealer or the company if the fault occurs under warranty. 3、The following situations is chargeable for maintenance under warranty: ① Faults or damages caused by the improper operation, repair or reinstall.
Bestter (Xiamen) Technology Inc Address:No 601,Tonghong Road,Tong'an Industrial .