Installation & Assembly

ManualsBrandsBesa Lighting ManualsLightingGeo 1-Light Flush Mount

FIXTURE INSTALLATION GUIDE

Model B0001wet, B0002wet, B0003wet, B0004wet

(Outdoor Wall Sconces 120V)

B0001wet,B0002wet,B0003wet,B0004wet, Rev.3 8-10

CAUTION: Turn off power to electrical box before installing

6695 Taylor Rd. Blacklick, OH 43004

www.besalighting.com

1. Disconnect power to outlet box at main electric box.

2. Fasten the mounting strap (A) to the outlet box using

machine screws (B) which should be found in the box.

3. Turn the threaded nipple (C) into the center hole in the

mounting strap.

4. Attach the branch circuit ground wire (I) to the green

screw on the mounting strap.

5. Hold the fixture canopy (E) close to the outlet box and

connect the fixture wires to the house supply wires

(black to black and white to white). Tighten securely

with wire nuts (D). Carefully push wires and wire nuts

back into the box.

6. Place the fixture canopy against the wall over the outlet

box oriented with the drainhole down of the canopy,

so that the threaded nipple protrudes through the hole on

the canopy. Place the cap nut (F) onto the threaded nipple

and tighten securely.`

7. Partially install the retaining screws (H) into the canopy.

8. IMPORTANT: IN ORDER TO COMPLY WITH ESTABLISHED ELECTRICAL CODE, THE INSTALLER MUST SEAL

THE AREA AROUND THE FIXTURE CANOPY, BETWEEN THE CANOPY AND THE WALL, WITH A TYPE OF

CAULKING COMPOUND SUCH AS SILICONE RUBBER TO PROVIDE A WATERTIGHT SEAL IN ACCORDANCE

WITH THE DIFFERING SURFACE TEXTURES OF THE WALL.

9. With the power still off, insert bulb of not more than the recommended wattage.

10. Place the glass/metal frame unit to the canopy (E). Seat the

neck of glass with metal frame (G) fully into the canopy (see

Fig.A ). Then secure by tightening the set screw (H) to be sure

the glass/metal frame is fully seated into the canopy.

DO NOT OVERTIGHTEN THE RETAINING SCREWS, MAY CAUSE

DAMAGE TO GLASS.

11. Restore the power.

Fig. A

(H)

Screw

Canopy

Glass/

Metal

Frame

(E)

(G)

Drainhole down

GLASS INSTALLATION

All electrical connections and the installation of this fixture must be in agreement with local codes, ordinances or

the NEC (National Electric Code) or CEC (Canadian Electrical Code). Do not connect this fixture to an electrical system

that does not provide a means for equipment grounding.

Summary of content (3 pages)

PAGE 1
FIXTURE INSTALLATION GUIDE Model B0001wet, B0002wet, B0003wet, B0004wet (Outdoor Wall Sconces 120V) 6695 Taylor Rd. Blacklick, OH 43004 www.besalighting.com B0001wet,B0002wet,B0003wet,B0004wet, Rev.3 8-10 CAUTION: Turn off power to electrical box before installing D 1. Disconnect power to outlet box at main electric box. 2. Fasten the mounting strap (A) to the outlet box using machine screws (B) which should be found in the box. H 3.
PAGE 2
FIXTURE INSTALLATION GUIDE Models using B0005 or B0006 Backplate (Exterior Wall Sconce 120V) 6695 Taylor Rd. Blacklick, OH 43004 www.besalighting.com B0005,B0006, Rev.3 8-10 CAUTION: Turn off power to electrical box before installing 1. Disconnect power to outlet box at main electric box. G 2. Fasten the mounting strap (A) to the outlet box using machine screws (B) which should be found in the box. D 3. Turn the threaded nipple (C) into the center hole in the mounting strap. B F 4.
PAGE 3
FIXTURE INSTALLATION GUIDE Models using B0008 or B0009 Backplate (Exterior Wall Sconce 120V) 6695 Taylor Rd. Blacklick, OH 43004 www.besalighting.com B0008,B0009_Rev.4 7-12 CAUTION: Turn off power to electrical box before installing 1. Disconnect power to outlet box at main electric box. G 2. Fasten the mounting strap (A) to the outlet box using machine screws (B) which should be found in the box. D 3. Turn the threaded nipple (C) into the center hole in the mounting strap. B 4.