Digital Projector User Manual Home Entertainment Series l TK810 V1.
Warranty and Copyright information Limited warranty BenQ warrants this product against any defects in material and workmanship, under normal usage and storage. Proof of purchase date will be required with any warranty claim. In the event this product is found to be defective within the warranty period, BenQ's only obligation and your exclusive remedy shall be replacement of any defective parts (labor included).
Table of Contents Warranty and Copyright information ................................................................................ 2 Important safety instructions .............................................................................................. 4 Introduction .......................................................................................................................... 7 Shipping contents .............................................................................................
Important safety instructions Your projector is designed and tested to meet the latest standards for safety of information technology equipment. However, to ensure safe use of this product, it is important that you follow the instructions mentioned in this manual and marked on the product. 1. Please read this manual before you operate your projector. Save it for future reference. 2. Do not look straight at the projector lens during operation. The intense light beam may damage your eyes. 3.
13. Always place the projector on a level, 9. Never replace the lamp assembly or any horizontal surface during operation. electronic components unless the projector is unplugged. - Do not use if tilted at an angle of more than 10 degrees left to right, nor at angle of more than 15 degrees front to back. Using the projector when it is not fully horizontal may cause a malfunction of, or damage to, the lamp. 10. Do not place this product on an unstable cart, stand, or table. The product may fall, 14.
17. Do not place liquids near or on the projector. 20. Do not place this projector in any of the Liquids spilled into the projector may cause it following environments. to fail. If the projector does become wet, - Space that is poorly ventilated or confined. Allow at least 50 cm clearance from walls and free flow of air disconnect it from the power supply's power around the projector. outlet and call BenQ to have the projector - Locations where temperatures may become serviced.
Introduction Shipping contents Carefully unpack and verify that you have all of the items shown below. If any of these items are missing, please contact your place of purchase. Standard accessories Projector Remote control with batteries User manual CD Quick start guide and Warranty card* Power cord USB wireless dongle • The supplied accessories will be suitable for your region, and may differ from those illustrated. • *The warranty card is only supplied in some specific regions.
Projector exterior view 7 8 23 6 4 1 5 9 2 3 10 3 4 11 2 20 12 13 14 15 16 17 18 2 24 19 20 20 22 3 20 3 20 2 20 21 22 3 1. Lamp cover 13. USB Mini-B port (for firmware upgrades) 2. Projection lens 3. Adjuster feet 14. USB Type-A port (USB 3.0: 5V 1.5A media reader/drive, firmware download) 4. IR remote sensor 15. HDMI 1/ HDMI 2 input port (Version 2.0b) 5. External control panel (See Controls and functions on page 9.) 16. USB Type-A port (USB 2.0: 2.5A power supply) 6.
Controls and functions Projector & Remote control All the key presses described in this document are available on the remote control or projector. 5 1 2 1. OK Used to confirm the selection on the BenQ Launcher menu. 2. Turns the projector off and on after initial startup. 6 3. 3 7 4 Power Back Used to return to the previous layer. 4. Settings Enter Settings menu. 5. POWER indicator light/TEMPerature warning light/LAMP indicator light (See Indicators on page 51.) 6. Arrow keys ( , 8 2 7. 8.
12. Microphone 14. Receives voice command. Press this key to enter the BenQ Launcher home menu. 13. LED Indicator Flashes when the key is pressed or when doing 15. Bluetooth Remote Control Pairing. Press Home and Menu on the remote control at the same time for at least 3 seconds until the LED Indicator is flashing for pairing. If pairing is completed, then the LED Indicator will stop flashing. Home* Menu* Launches the Apps related settings when operating in All Apps.
Positioning your projector Choosing a location Before choosing an installation location for your projector, take the following factors into consideration: • Size and position of your screen • Electrical outlet location • Location and distance between the projector and the rest of your equipment You can install your projector in the following ways. 1. Front Table 2. Rear Table Select this location with the projector placed on the table in front of the screen.
Obtaining a preferred projected image size The distance from the projector lens to the screen, the zoom setting (if available), and the video format each factors in the projected image size. Projection dimensions 16:9 Screen diagonal Screen Center of lens H W Vertical Offset Projection distance • The screen aspect ratio is 16:9 and the projected picture is in a 16:9 aspect ratio Screen size Distance from screen (mm) Diagonal Min length H (mm) W (mm) 664 Max length (max. zoom) Average (min.
bracket. This will perform the secondary role of restraining the projector should its attachment to the mounting bracket become loose. • Ask your dealer to install the projector for you. Installing the projector on your own may cause it to fall and result in injury. • Take necessary procedures to prevent the projector from falling off such as during an earthquake. • The warranty doesn’t cover any product damage caused by mounting the projector with a non-BenQ brand projector mounting kit.
Operation Installing the USB wireless dongle Follow the illustrations below to install the USB wireless dongle. Make sure that the lamp cover is installed back after the USB wireless dongle is plugged. Do not turn the power on with the lamp cover open. 1 2 4 5 3 Starting up the projector 1. Plug the power cord. Turn on the power outlet switch (where fitted). The power indicator on the projector lights orange after power has been applied. 2. Plug the USB wireless dongle.
Step 1: Select Projector installation. For more information about projector position, see Choosing a location. Step 2: Select Language. Step 3: Configure the Remote Control Pairing Press Home and Menu on the remote control at the same time for at least 3 seconds until the LED Indicator is flashing for pairing. If pairing is completed, then the LED Indicator will stop flashing. Step 4: Adjust Vertical Keystone.
Step 6: Select Time Zone. Step 7: Read Privacy Policy and press OK. You’ve completed the setup wizard; you may now connect a device to the projector to project video. See Connection on page 22 for more information. • Please use the original accessories (e.g. power cord) to avoid possible dangers such as electric shock and fire. • If the projector is still hot from previous activity, it will run the cooling fan for approximately 90 seconds before energizing the lamp.