Federal Communications Commission (FCC) Statement This Equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference 10 radio communications.
Unpacking the Package Chapter 1 Unpacking the Package Check following rems. If they are missing or damaged, consult your place of purchase immediately. Overview 211c color monitor User's manual Ne @ Power cord 15-pin D-SUB Macintosh adapter signal cable #5 Locate the model name and the serial number labeled on the back | of your monitor. Write down the related information of your monitor and dealer in the space on page iii for future reference.
Chapter 1 Features Super-fine Dot Pitch With 0.26mm super-fine dot pitch and anti-static coating, Overview 2c color monitors offer strikingly sharp and high resolution image up to 1600 x 1200, Wide Range Auto Scan Horizontal frequency ranges from kHz to 107KHz to support 1600 x 1600 @ 91st-z resolution. Flicker Free design for vertical frequency of up to 160Hz. i Key Pressing the i key, the monitor will automatically (Fuzzy Auto calibrating) adjust displays size and position to the optimum.
re) Unpacking the Package Power Management ee The Rawer management of this monitor complies with these VASE power saving modes: Mode Power Horizontal Vertical LED Consumption __ Synge Sync On Normal On On Green Stand-by < BW Off On Amber Suspend < EW Off off Amber Off <35W Off Off Amber Blinking Override Normal Off off Green | Factory Preset Timings ) Resolution Vertical Frequency Horizontal Frequency (Hz) (KHz) 640 x 400 70 3147 640 x 480 60 3147 640 x 480 75 37.50 800 x 600 75 46.88 1024 x 768 75 50.
Chapter 2 Chapter 2 Installing the Monitor This monitor is equipped with an autosuggestion universal compatible power supply for voltage ranges AC, 50~60Hz.. Please confirm the line voltage resignation at the rear panel of the manor before connecting the machine, Power cord 1) Make sure that the system power is turned off. 2) Please refer to the instructions below to connect the signal cable through D-SUB or BNC. 3) Connect the power cord to the monitor and attach it to power source.
— Installing the Mani tor (Connecting the Signal Cable ) Your Overview lick provides both D-SUB and BNC signal connectors. The D-SUB or BNC signals can automatically be detected by its microprocessor. = Connecting through D-SUB signal connector Temp 0 Lom 1) Make sure that the system power is turned off 2) Connect the computer end of the D-SUB cable to the 15-pin output connector on the video board of your computer.
Chapter 2 (Connecting to An Apple J) If you connect the monster to an Apple Macintosh through a D-Sub cable, you need to 2dd the Macintosh adapter to connect the video signal port of your computer and the monitor signal cable, Before connecting the adapter please refer to the user's guide of the adapter to set the switches of the adapter.
rear stalling the Monitor 1) Make sure that the system power is turned off, 2) Connect the computer end of the BNC cable to the output connector on the video board of your computer, 3) Cornet the monster end of the BNC cable to the BNC receptacle on the back of the monitor, Connecting through BNC Signal Connector Li (Bos Edd bo BNC ic
Chapter Chapter 3 A Look at the Control Panel Menu key : enters or changes Main menus. There are three main menus. Enter key : enters sub-menus or selects ems. Exit key : goes back to main menus {auto save), or leaves OSD. A & v key : scrolls the light colored bar up or down and represents HOT KEY for brightness adjustment. «| & WP key : scrolls the light colored bar left or right and represents HOT KEY for contrast adjustment. ¢ hey: is used for Fuzzy Automatic calibration adjustment.
A look at the Making Adjustments ) ¢ éey (Fuzzy Auto Calibration ) Just push the ¢ deg then the monitor will automatically adjust display's size and position to the optimum, No re-configuration or adjustment is needed when a user changes display mode. The ¢ deg function is different from "Reset" function. Reset” function for display’ geometry, size and position only works under the factory preset timings {please see page 3).
Chapter 3 IT OSD Operation Press Menu key to enter (change) Mari menus (there are three main menus} Press A or WF keys to scroll it colored bar to desired items. Press Enter key to enter sub-menus. Press key to do the adjustments. If the sub-menu contains multiple items. Press A or WF keys to scroll fight colored bar to desired items. Then press «for Ie key to adjust as required. Press Exit key to save and return to main menus.
A Look at the — | Campanella “dos » Luminescence PN Contrast and Brightness adjustments OSD Manager @0 Contrast adjusts the difference between the light and dark areas. Xt Brightness adjusts the brightness of the display. OO) Size & Position Display size and position adjustment i or O50 Manager 1 Hor. Position Hor. Size Ver. Position Ver.
Chapter 3 E] Hor, Position adjusts the horizontal position of the display. == Hor. Size adjusts the width of the display. = Ver. Position adjusts the vertical position of the display. [3] Ver. Size adjusts the vertical height of the display [of Geometry Advanced geometry adjustments 3 1a A DR BOD Pincushion controls the straightness of the vertical edges of the display.
A Look at the ~~ _ =] OSD Position OSD position adjustments adjusts the OSD menu position up. adjusts the GSD menu position down. adjusts the OSD menu position left, adjusts the OSD menu position right. Degassed Manual Degassed.
Chapter 3 Main Meany 2 Color Control OSD Manager Color Adjustment C1 9300K 6500K 5500K T7100K 11500K This main menu is defined as color weight adjustment, C1 ~ C5 are color storage areas, which are factory preset but can also be modified by user. The preset information as follows Factory Default Color Temperature Ci 9300K <2 6500K C3 5500K C4 160K Cs {1500K Scroll the fight colored bar to desired color temperature, then press Exit to save the setting and leave OSD.
A Look at the i OSD Manager 1 | C1 8300K C1 | RO wee) 100 100 cs 785 B 0 seem 100 75 »od Ra set to Default This sub-menu adjusts RGB (Red, Green, Blue) color weight. Press or 'W keys to scroll light colored bar to desired items then press € or » key to do the adjustments.
Chapter 3 N f= Convergence Horizontal & Vertical Convergence adjustment OSD Manager . 1 H3 Hor. Convergence = Var, Convergence FH Hor. Convergence: adjusts Horizontal Convergence = Ver. Convergence: adjusts Vertical Convergence Convergence is tre monitor's ability to precisely Ruminate specific phosphors and line therm up properly in order to produce pure color. Displayed characters and images may appear fuzzy or have tinges of red, green, or blue if the electron beams do not converge correctly.
A Look at the J Moire Horizontal & Vertical Moire adjustment OSD Manager Horizontal Moire Vertical Moire = bed “a | E=3 Vertical Moire: adjusts vertical Moire Moire refers to an interference pattern of dark wavy lines on the screen, It is an interference henchmen caused by the relationship between the phosphor layout and the imaging signal. In fact, i is often considered an indication of good focus level, 1&5 It is especially noticeable when using a light-gray or every-other dot pattern.
Chapter 3 I pac] Language Select 08D Manager Putsch English Parasol Francis totalitarian GREECE The sub-menu is defined as language selection and there are five languages to choose from, 5. D-Sub «4» BNC Input connector select, OSD Manager There are two kinds of input connectors for Overview 21. One is a BNC connector, the chert is a DB-15. The milch is capable of automatically detecting the type of connector used (either BNC or DB-15).
A Look at the 1 __ Control Panel £3 Purity Co lour purity adjustment OSD Manager E32 puny To adjust Purity, choose a fll white picture and adjust to gat a pure white picture at the corner of the screen mage. [CI] Display Mode Current resolution, horizontal and vertical frequency status presentation. Display Mods 1024 X 768 Ou kos H.F 59.
Chapter 3 Timing Setting By making adjustments to your video card settings, you can set the timing and the refresh rate according to your preferences. The monitor wil automatically save the settings.
A Look at the Control Panel Pin Assignments D-SUB Connectors Signal Pin No Separate Composite | Sync-on-green | Red Red Red 2 Green Green Green + SYNC 3 Blue Blue Blue GND GND GND 6 R-END R-END R-END 7 DONG G-END G-END 8 B-END B-END 8-END 9 PCSV(For DDC) PCSY{For DDC) PC5V(For DDC) 0 END-SYNC END-SYNC END-SYNC 1 GND GND GND 12 DOC Data DDC Data DDC Data 3 H-SYNC HA-SYNC Not Used i V-SYNC Not Used Not Used 15 DBC Clock DDC Clock DOC Clack
Chapter 4 BNC Connectors ©0006 @/Sync R HH+V Pin Signal Assignment separate composite sync-on-green 8 Blue Blue Blue SYNC Green Green Green + SYNC R Red Red Red Hilly H-SYNC H-SYNC NC V V-SYNC
A Look at the —31 Control Panel Chapter Troubleshooting Make sure that your monitor is properly installed. If you have encountered any trouble n using this product, for hardware installation problems, see Chapter 2, Installing the Monitor. if the problems persist, check this chapter for possible solutions. If you cannot find Overview 2H ¢ on the Windows 95 monitor fist, you wooed have to update the Windows 95 setup information for Overview ic.
Chapter 4 § If the characters look dark, the picture is too small, too large or not centered efc. ® Adjust related settings. See Chapter 3, A Look at the Control Panel, § If colors are impure. ® Check signal cable connector pins. If pins are bent or missing, consult your dealer Adjust the Purity setting See Chapter 3, A Look at the Control Panel. Maintenance X Do not expose the monitor to direct sunlight or heat. X Do not spit liquid on the monitor. X Donor attempt to open the monitor.
Specifications Chapter 5 Specifications Picture Size diagonal AG Pitch 026mm dot pitch Surface Transmission Maximum Viewable Size 20” (LCM) diagonal Video Input 15-pin, mini D-SUB Connector Connector Bandwidth 230MHz Display Area 380mm (MH) x 285mm(V) (Preset) 408mm(H) x 206mm(V) (Full Scan) Power Supply(Universal)| Input voltage VAC, 50-60 Hz (Universal compatible) Power consumption 150 Watts max/ 165 Watts max.