Datasheet

ManualsBrandsBeltrona ManualsAccus & Batteries3AA2200ESO Battery pack 3x AA Plug NiMH 3.6 V 1500 mAh

(Type)

：LS49AA2200P

Specifications of single cell

Note:

Nominal capacity, rated at 0.2C 20℃.

Average capacity, for reference only.

Weight and internal impedance are For reference.

Nominal voltage

1.2V

Capacity

0.5C Discharge

Minimum

116min

Typical

121min

Dimensions

Diameter

14.5

-0.7

Height

49.0

-1.0

Weight(Approximately)

gram

28.0

Internal Impedance At 1000 Hz

30m



(Max)

After Charge

Charge

Standard

220mA(0.1C)

16hrs

Rapid

1100mA(0.5C)

2.1hrs

Ambient

temperature

Charge

standard

℃

0℃ to 40℃

Rapid 0℃ to 40℃

Discharge

-20

℃

to 50

℃

Storage

-20

℃

to 30

℃

Number of cycles life curve

Nominal capacity (%)

Cycle life characteristics

℃

charge time (hours)

Charge: 0.1C

16hrs.

Typical characteristics

Standard charge

characteristics

PVC

(

Dimensions with tube

)

(mm)

Charge retention curves of Ni-MH cylindrical cell At

20℃ storage temperature

Capacity Reserve (%)

Rapid charge

Charge: 0.5C

2.1hrs.

Voltage (V)

Voltages (V)

charge time (hours)

Voltages (V)

Discharge capacity (%)

Discharge characteristics

℃

2 3 4 5 6 7 8 9 10 11 12

Time(month)

100

20°C

BELTRONA GmbH & Co. KG

electronic components

Schmeienstraße 50

D-72510 Stetten a.k.M.

Telefon +49 75 73 951 33 0

Telefax +49 75 73 951 33 99

www.beltrona.de

info@beltrona.de

BELRTUAA2200

1.2V 2200 mAh

1 / 8

Summary of content (8 pages)

PAGE 1
BELRTUAA2200 1.2V 2200 mAh Typical characteristics Standard charge characteristics Charge: 0.1C ×16hrs. (Type)：LS49AA2200P 0.5C 116min 121min mm 14.5-0.7 49.0-1.0 gram 28.0 30m(Max) Minimum Typical Diameter Dimensions Height Weight(Approximately) Internal Impedance At 1000 Hz Standard Rapid Charge Ambient temperature Charge standard After Charge 220mA(0.1C)×16hrs 1100mA(0.5C)×2.1hrs ℃ 0℃ to 40℃ Storage ℃ charge time (hours) Rapid charge Charge: 0.5C×2.1hrs.
PAGE 2
BELRTUAA2200 1.2V 2200 mAh 4. Standard according as IEC of test cycle life。 1. PREFACE Time (month) The specification is suitable for the performance of NI-MH rechargeable battery produced by the SHENZHEN FBTECH CO., LTD. 2. MODEL AA2200mAh 1.2V 3. APPEARANCE There shall be no such details as discoloration or electrolyte leakage or 0 voltage. 4. RATINGS Description Nominal Voltage Typical Capacity Nominal Capacity Minimum Capacity Standard Charge Unit Specification V 1.
PAGE 3
BELRTUAA2200 1.2V 2200 mAh 5. PERFORMANCE Before proceed the following tests, the cells should be discharged at 0.2C to 1.0V cutoff. Unless otherwise stated, tests should be done within one month of delivery under the following conditions: Ambient temperature: Relative Humidity: 20℃±5℃ 65±20% Note Standard Charge/Discharge Conditions: Charge: Discharge: Test Capacity High Rate Discharge (2.0C) Low Temperature Discharge Overcharge 440mA(0.2C) to 1.
PAGE 4
BELRTUAA2200 1.2V 2200 mAh Humidity N/A External Short Circuit N/A Safety Device Operation N/A Free falling(drop) N/A No leakage No fire and explosion Standard charged, stand for 14 days at 33 ±3℃ and 80±5% of relative humidity no No explosion △V<0.02V/cell △Ri<5%/cell After standard charge, short-circuit the cell at 20℃±5℃ until the cell temperature returns to ambient temperature.(cross section of the wire or connector should be more than 0.75mm2) Forced discharge at 0.
PAGE 5
BELRTUAA2200 1.2V 2200 mAh 6. PRECAUTIONS TO ENSURE THE SAFETY ON BANDING BATTERY 1. Batteries should be charged prior to use. 2. .When using a new battery for the first time or after long term storage, please fully charge the battery before use. 3. For charging methods please reference to our technical handbook. 4. Use the correct charger for Ni-Cd or Ni-MH batteries. 5. Do not reverse charge batteries. 6. Do not short circuit batteries, permanent damage to batteries may result. 7.
PAGE 6
BELRTUAA2200 1.2V 2200 mAh When connecting a battery pack to a charger, ensure correct polarity. 15. If find any noise, excessive temperature or leakage from a battery, please stop its use. 16. When the battery is hot, please do not touch it and handle it, until it has cooled down. 17. Do not remove the outer sleeve from a battery pack nor cut into its housing. 18. When find battery power down during use, please switch off the device to avoid overdischarge. 19.
PAGE 7
BELRTUAA2200 1.2V 2200 mAh 7. : IEC61951-2 ED3.0 . 1 0.1CtA for 16 h 2 to 48 0.25 CtA for 3 h 10 min 49 0.25 CtA for 3 h 10 min 50 0.1 CtA for 16 h  100,150,200,250,300,350,400and 450  None None None 1h to 4h 0.25 CtA for 2 h 20 min2) 0.25 CtA for 2 h 20 min2) 0.25 CtA to 1.0V 0.2C5A to 1.0V1) . Append: IEC61951-2 ED3.0 Endurance in cycles Before the endurance in cycles test, the cell shall be discharged at 0.2 1tA to a final voltage of 1.0V/sell.
PAGE 8
BELRTUAA2200 1.2V 2200 mAh 8. ENVIRONMENTAL PROTECTION REQUIREMENT 8.1 It is hereby certified by FBTECH that there is neither RoHS (EU Directive 2002/95/EC, 2011/65/EU, 2015/863) restricted substance nor such use, for materials to be used for unit parts, for packing/packaging materials, and for additives and the like in the manufacturing processes. 8.2 Battery Cells restricted substance conform to the requirements of the Battery Directive (EU Directive 2006/66/EC,2013/56/EU) 8.