User's Manual

ManualsBrandsBellmate Holdings ManualsElectronicsWireless Controller

T631W-2TX Operation Instruction

M Specification

1. Temperature display range: 0-40 ℃(32-99℉)

2. Temperature control range: 7-32℃(44-90℉)

3. Accuracy: ±1℉(at 68 ℉)

4. Power source: 2X AA 1.5V BATTERY

5. Load Rating: 1.5 Amp maximum

6. Static current: ≤ MA(DC3V)

7. Reading temperature current: ≤0.25MA(DC3V)

8. Backlight on current: ≤MA(DC3V)

9. Blue backlight

10. RF frequency: 916MHZ.

M T631W-2 TX:

When thermostat is connected with power, it will show full display and stay in

continuous transmission mode

normal mode.

M TEMPERATURE SETTING

Press “+”or “-“ to set temperature.

FAN SETTING

(it’s test mode), press “+”/”-“ key to enter into

1. In LOW position: GL is continuously on.

2. In HIGH position: GH is continuously on.

3. In AUTO position: it follows system to turn on or turn off.

M SYSTEM SWITCH SETTING

1. COOL: it runs in cool mode. When cooling is on, it will display “ON”.

2. OFF: system will not work.

3. HEAT: it runs in heat mode. When 1

heating is on, it will display “ON”. When 2nd

heating is on, it will display “+1”.

M Technical Setting

1. HEAT SWING SETTING

In HEAT mode, hold down “+” and “-”key for 3 seconds to flash “04” (factory default 0.4).

Press “+” or “-” key to set heat swing range from 02 to 20 (0.2 - 2.0) degree. It will

automatically confirm and exit in 15 seconds if no further key pressing.

2. COOL SWING SETTING

In cool mode, hold down “+” and “-”key for 3 seconds to flash “05” (factory default 05).

Press “+” or “-” key to set cool swing range from 0.2 to 2.0 (0.2 - 2.0) degree. It will

automatically confirm and exist in 15 seconds if no further key pressing.

Summary of content (4 pages)

PAGE 1
T631W-2TX Operation Instruction M Specification 1. Temperature display range: 0-40 ℃(32-99℉) 2. Temperature control range: 7-32℃(44-90℉) 3. Accuracy: ±1℉(at 68 ℉) 4. Power source: 2X AA 1.5V BATTERY 5. Load Rating: 1.5 Amp maximum 6. Static current: ≤ MA(DC3V) 7. Reading temperature current: ≤0.25MA(DC3V) 8. Backlight on current: ≤MA(DC3V) 9. Blue backlight 10. RF frequency: 916MHZ.
PAGE 2
3. CALIBRATION SETTING In OFF mode, hold down “+” and “-”key for 3 seconds to display “CA” and flash “0” (factory default 0). Press “+” or “-” key to set calibration range from -4 to 4 degree. It will automatically confirm and exit in 15 seconds if no further key pressing. 4. B/O (for HEAT/COOL) SETTING Last step don’t confirm, hold down “+” and “-”key at the same time to display “CO” and flash “b” (factory default b). Press “+” or “-” key to select b or o.
PAGE 3
M RESET 1. Press “RESET” key once (on the PCB board) to reset thermostat. 2. Hold down “+” key, then press “RESET” key (on PCB) once to resume factory defaults. M T631W-2 RX SPECIFICATION 1. Power source: (1) 24V AC (18- 30V) 2. RF frequency: 916MHZ. M T631W-2 TX and RX COMMUNICATION 1. Hold T631W-2RX key for 3 seconds, blue LED will flash. 2. Let T631W-2TX enter into learning status (step 8 on Technical setting), then hold “+” key for 3 seconds.
PAGE 4
Statement according to FCC part 15.19: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Statement according to FCC part 15.105: NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.