USER GUIDE X series mobile medical alert system Rating 5VDC 1A
H O W TO C H A R G E B E L L E IMPORTANT: Fully charge Belle before first use. ® Plug in the charging cradle and place Belle into the cradle as shown. Typical charging time is 2-3 hours. The light flashes red every 5 seconds while charging and is solid red when Belle is fully charged. NOTE: Battery life will vary based on settings selected by your dealer. Please contact your dealer with any questions. Only charge as needed. Wear your device as often as possible to be protected.
speaker call button X series microphones blue call light / red battery light Red battery light While charging, the light will flash red every 5 seconds until the device is fully charged. Once fully charged, the light will be solid red. If the battery is low, the light will slowly flash red when off the charging cradle. Blue call light During an SOS call, the light will be solid blue.
H O W TO C A L L F O R H E L P how to call for help 1. Press and hold the call button until the light turns blue. 2. After a short delay, you will hear a voice message and then tones or ringing. 3. The specialist will answer the call. 4. The specialist can send emergency personnel or loved ones to help you. If your Belle® does not connect properly, please contact your dealer immediately. Fall detection is an optional feature.
R E P L A C E L A N YA R D W I T H B E LT C L I P 1. Remove the lanyard by pressing the small tab upward to release the clip. 2. Pull the lanyard and clip away from the Belle® device. 3. Press the belt clip onto the back of Belle as shown until it clicks. 1 2 3 C L E A N I N G B E L L E W E E K LY We recommend that you clean Belle weekly to ensure proper charging.
howBYtoUSING callTHIS forDEVICE, helpYOU ACKNOWLEDGE AND A Coverage: This product requires that there be adequate cellular coverage to work properly. It is important to test the device to know if it works in your area. Remember that your environmental and topographical conditions may also affect your coverage. If you experience coverage issues, please contact your dealer immediately. Charging: Battery life will vary based on settings selected by your dealer. Please contact your dealer with any questions.
EDGE AND ACCEPT THE FOLLOWING INFORMATION. Fall Detection: Fall detection is an optional service for Belle® and uses patented algorithms to detect falls. If a fall is detected, you will be connected to specialists who can dispatch emergency services if needed. You will be able to tell specialists if you do not need assistance. We cannot guarantee that the service will always accurately determine a fall. It is advised that you always press the button if you need help.
ANY AND ALL LOCATION-BASED INFORMATION IS MADE AVAILABLE FOR INFORMATIONAL AND PLANNING PURPOSES ONLY AND IS NOT INTENDED TO BE RELIED UPON IN SITUATIONS WHERE PRECISE LOCATION INFORMATION IS NEEDED OR WHERE ERRONEOUS, INACCURATE, TIMEDELAYED OR INCOMPLETE LOCATION OR MAP DATA MAY LEAD TO DEATH, PERSONAL INJURY, OR PROPERTY OR ENVIRONMENTAL DAMAGE.
FCC This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user‘s authority to operate the equipment.
—Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. IC This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: 1.
Cet appareil contient des émetteurs / récepteurs exemptés de licence conformes aux RSS (RSS) d’Innovation, Sciences et Développement économique Canada. Le fonctionnement est soumis aux deux conditions suivantes: 1. Cet appareil ne doit pas causer d’interférences. 2. Cet appareil doit accepter toutes les interférences, y compris celles susceptibles de provoquer un fonctionnement indésirable. CAN ICES-3(B)/NMB-3(B) Manufacturer: Freeus, LLC www.freeus.com support@freeus.
X series