User Manual

4-Way HDMI
®
Switch with Wireless Remote
Quick Installation Guide
4-Way HDMI
®
Switch with Wireless Remote
Quick Installation Guide
Package Contents
• 4-Way HDMI Switch • Remote Control
• Infrared Extender/Receiver • Quick Install Guide
IMPORTANT NOTE: POWER SUPPLY
When an HDMI cable is used with an HDMI device, this Switch will be powered by
the 5V that always runs from a standard HDMI device through the cable.
If this Switch is connected to a non-HDMI device or connected to a long HDMI
cable, there is a port on the Switch that will accept the necessary power supply.
This power supply is not included and must be purchased separately.
Introduction
Congratulations and thank you for purchasing the Belkin 4-Way HDMI Switch
with Wireless Remote.
This product allows you to connect and switch among four separate HD video
sources and use only one HDMI connection on your HDTV. This allows easy
switching between devices such as HD gaming systems, Blu-ray
®
players, and
HD set-top boxes with a wireless remote. There is also an intelligent switching
function, which detects the device that is powered on and automatically switches
to that device.
Benefits
• Connect and switch among four HD video sources using only one HDMI
connection on your HDTV
• Supports 480i, 480p, 720i, 720p, 1080i, and 1080p video resolutions
• Supports 3D signals
• Select connected devices from the IR remote control (supplied) or via the
front-panel “Input Select” button
• LED indicator shows current source device
Installation
1. Place the 4-Way HDMI Switch away from heat, moisture, and sources of
electromagnetic or radio frequency interference.
2. Connect HD source devices into the ports marked “Input 1, 2, or 3”
3. Connect the HDMI switchbox to the HDTV through the port marked “Output”
4. Plug the IR remote sensor through the small, round port on the side of the
HDMI switchbox market “IR.”
5. Place the IR sensor in a visible place near the front of the product with clear
access to remote control commands (length = 50cm)
6. When the power of the HD source is turned on, the
HDMI Switch will automatically select that input to begin normal operation.
Remote Control
1. Press the “Input Select” button repeatedly until the desired input is selected.
2. Each press progresses to the next input in turn (i.e., 1-2-3, then back to 1).
3. The current input is identified by the lighted LED indicator on the front panel.
© 2012 Belkin International, Inc. All rights
reserved. All trade names are registered
trademarks of respective manufacturers
listed. HDMI is a trademark or registered
trademark of HDMI Licensing LLC in the
United States and other countries.
AV10117uk • 8830-10234 Rev. A00
Belkin.com
Belkin Ltd.
Express Business Park
Shipton Way, Rushden
NN10 6GL, United Kingdom
Belkin B.V.
Tupolevlaan 1
1119 NW Schiphol-Rijk
Netherlands
Belkin International, Inc.
12045 E. Waterfront Drive
Playa Vista, CA 90094, USA
Output Video HDMI 1.3b
Maximum Single
Link Range
1920x1080p
Frequency Range 50/60Hz
Video Amplifier Bandwidth 2.5Gbps/250MHz
Video Screen Resolutions 480i, 480p, 720i, 720p, 1080i, 1080p
Operating Temperature 0° C to +70° C
Operating Humidity 10% to 85% RH (no condensation)
Storage Temperature -10° C to +80° C
Storage Humidity 5% to 90% RH (no condensation)
External Power Supply No external power needed
IR Receiver 3.5mm stereo jack; 50cm cable length
Dimensions (L x W x H) 80mm x 58mm x 17mm
Warranty Limited Lifetime Warranty
Input DC Power 5 Volts
Power Consumption 5 Watts (max.)
Specifications
Four-Way
HDMI
®
Switch
Full HD
Blu-ray
®
Player
HD Gaming Console
Laptop
HD Cable/Satellite Box
Optional Power Supply