Dishwasher User’s Manual Installation Manual DDN25401X DDN25402W DDN25402X DDT25401B DDT25401W DDT25401X DDT36430X DDT36430XIH DDT38530BX DDT38530X DDT38530XIH DDT38530XWS DDT38532X DDT38532XIH DDT39432CF DDT39432X DDT39432XIH DDT39434CF DDT39434X DDT39434XIH DIN25401 DIT25401 DIT38530 DIT38532 DIT39432 DIT39434 DUT25401B DUT25401W DUT25401X DUT36420W DUT36420X DUT36520W DUT36520X DUT36522W DUT36522X USA Document Number : 15 9889 0100_BEKO_USA/ 24-08-21.
To prevent accidents, which could cause serious injury or death, as well as machine damage read these instructions before installation and / or use. INTRODUCTION 1. IMPORTANT SAFETY INSTRUCTIONS 1 1 2. TOOLS WHICH MAY BE NEEDED 3. MATERIALS WHICH MAY BE NEEDED 4. MATERIALS SUPPLIED 3 3 4 5. DISHWASHER SPECIFICATIONS 5 6. ENCLOSURE PREPARATION 7 1.1 INSPECT THE DISHWASHER 4.1 PARTS SUPPLIED 4.2 MANUAL BAG 4.3 DISHWASHER PARTS BAG 1 4.4 DISHWASHER PARTS BAG 2 4.
INTRODUCTION NOTICE : Please read this installation manual and particularly the safety instructions completely and carefully. They will save you time and effort and help to ensure optimum dishwasher performance. Read these installation instructions completely before installing and follow them carefully. Save these installation instructions and pass them on to any future user. Be sure to observe all listed warnings and cautions. Look particularly for the icons with exclamation marks inside.
• • • • • • • If the dishwasher is installed in a location that experiences freezing temperatures (e.g. in a vacation home, cabin, etc.), you must drain all the water from the dishwasher’s interior. Water system ruptures that occur as a result of freezing are not covered by warranty. Dishwasher must be secured to adjacent cabinetry using the brackets provided. Failure to do this may cause damage to property or bodily injury.
2. TOOLS WHICH MAY BE NEEDED 3. MATERIALS WHICH MAY BE NEEDED (Additional materials may be required to comply with local codes) Hot Water Supply Line - Minimum 3/8” O.D. copper tubing or metal braided dishwasher supply line. Elbow with 3/4” FHT(female threaded) for dishwasher side, and sized to fit your water supply line (copper tubing/compression fitting, or braided hose) on the other side. Dishwasher connection is 3/4” male. UL listed conduit connector or strain relief.
4. MATERIALS SUPPLIED 4.1 PARTS SUPPLIED Parts for your dishwasher will come in several plastic bags. Check your parts bags shown to make sure you have all the parts as listed to the left. 4.2 MANUAL BAG The dishwasher comes with a manual bag containing: • User manual, • Installation manual 4.3 DISHWASHER PARTS BAG 1 x4 x2 This dishwasher bag comes with the following parts: a. Side Trim Strips (Left) b. Side Trim Strips (Right) d. Screws Ø 1/8” x 5/8” (Ø 3.5 mm x 14 mm) e. Mounting Bracket Left f.
5.
5.1 TECHNICAL FEATURES Permissible water pressure Electrical connection Total power Heater power 4.35 - 145 psi (0.3 - 10 bars) 120 V (volts), 12 A (amps), 60Hz (hertz) 1400 W (watts) 1100 W (watts) NOTICE : Because we continually strive to improve our products, we may change our specifications and design without prior notice. This device corresponds to the following directives: UL 749 Household Dishwasher directive.
6. ENCLOSURE PREPARATION 6.1 ELECTRICAL PREPARATION WARNING The dishwasher is designed for an electrical supply of 120 V, 60 Hz, AC, connected to a dishwasher-dedicated, properly grounded electrical circuit with a fuse or breaker rated for 15 amperes. 6.
d) ? 8 USA
j (Depends on model) + 50 max 50 (+50mm) WARNING Dishwasher must be secured to adjacent cabinetry using the mounting brackets provided. Failure to do this may cause damage to property or bodily injury.
Place the two mounting brackets into the top corners of the dishwasher. Fix the mounting brackets (A) to the top corners of the dishwasher, with the screws supplied. Bend sides of mounting brackets (B) in order to fix from sides (if necessary). 6.3 ADJUSTING HEIGHT If the height of the enclosure is 337/8” to 357/8” (861 mm - 911mm) adjust supports as shown in the figure. Supplied (4) Adjust the front foot level with the adjusting wrench to balance and raise the dishwasher to the enclosure height.
6.4 INSTALLING THE SIDE TRIM STRIPS Remove the adhesive tape (Figure A). Place the trim strips on the front edge of the side walls (Figure B). NOTICE : • Make sure you use the correct trim strip since there is a left and right side strip. The flexible material should be facing forward (Figure B). 6.5 PREPARING THE WATER CONNECTION (A) Install an easily accessible shut-off valve (not supplied) in the water supply line.
WARNING Installation should be performed by a qualified installer. Work by unqualified persons could be dangerous and may void the warranty. If the dishwasher is installed in a location that experiences freezing temperatures (e.g. in a vacation home, cabin etc.), you must drain all the water from the dishwasher’s interior. Water system ruptures that occur as a result of freezing are not covered by warranty. 6.
6.6.1 UNDER THE SINK DRAIN (ALTERNATIVE) • • • • Due to the local bu�ld�ng code requ�rements, some d�shwasher �nstallat�ons requ�re hook�ng up d�scharge hose to an a�r gap located next to the s�nk �n k�tchens. S�nce the connect�on d�ameter �s d�fferent than standard d�scharge hose connect�ons, please use the connector p�ece prov�ded w�th the mach�ne w�th �nstruct�ons �llustrated. 6.6.
6.7 STEAM PROTECTION FOIL Steam will form inside the dishwasher during operation. At the end of the cycle, when the dishwasher door is opened, it is required to use a steam protection foil to prevent any steam from collecting on the underside of the counter top. 6.6.2 FITTING THE PROTECTION FOIL Before applying the steam protection foil to the underside of the countertop, clean the area with a damp cloth (as shown in Figure A). Once the area dries, apply the steam protection foil.
7. PLACEMENT OF DISHWASHER INTO THE OPENING Now place the dishwasher into the opening and get ready to connect all hoses and electrical connections. CAUTION Make sure all hoses are pulled through the side opening of the cabinet, no hoses are kinked and all slack is taken out as shown in the above figure. 7.1 DRAIN HOSE CONNECTION, WATER SUPPLY & ELECTRICAL CONNECTIONS 7.1.1 DRAIN HOSE CONNECTION Connect the drain hose to the drain plumbing. 1.
7.1.2 WATER SUPPLY CONNECTION Water supply may be connected to the dishwasher in one of two ways: • With metal braided hose. • With copper tubing. • • CAUTION • • • • Hot water supply line: Use minimum 3/8” O.D. copper tubing or metal braided dishwasher supply line. Temperatures required for soldering and sweating will damage the dishwasher’s water inlet valve so if any such operation is needed, keep the heat source min. 77/8” (200mm) away from the dishwasher’s water inlet valve.
WARNING Improper connection of the equipmentgrounding conductor can result in a risk of electric shock. Check with a qualified electrician or service representative if you are in doubt whether the appliance is properly grounded. Do not modify the plug provided with the appliance, if it will not fit the outlet, have a proper outlet installed by a qualified electrician.
7.2 READJUSTING FOOT LEVELS Now that the dishwasher is in the cabinet you must readjust the feet to bring the dishwasher up to the required height and attach it underneath the countertop. 1. Readjust the front foot levels with adjusting wrench to balance the dishwasher and raise it up under the countertop, make sure the unit is level. 2. Readjust the rear foot levels with a screwdriver to balance the dishwasher and raise it to the required height using the brackets supplied. 3.
TALL TUB MODELS ONLY Open the fixing part on the Toe Kick(p). (A) Place it on the slots, which are on the brackets fixed before, and adjust the height (max. 40 mm). (B) Close the fixing part on the Toe Kick.
7.
TALL TUB MODELS y 21 USA
7.5 PREPARING THE TIMBER DOOR X o) X =? s) = = = = Mid. Point Mid.
7.
7.9 INSTALLING THE TIMBER DOOR 4 1 3 2 7.
7.11 FIXING THE TIMBER DOOR (yy) Ø 4 x 43mm 12 34 5 1 23 45 7.12 ADJUSTING THE KICK PLATE 25 USA • Check whether the bottom of the door hits the toe kick of the kitchen cabinet (A). • If the door hits the toe kick cut the necessary section out of the toe kick (B). • Apply silicon or sealant to the cut edge of the kitchen cabinet toe kick or paint so it does not absorb moisture.
4 ~ 1500 ~ 1800 ~ 2000 min 300 min 500 max 1000 1 1 2 2 1 1 26 2 USA min 300 2 min 120 max 1000 3 min 500 max 1000 7.
8. INSTALLER CHECKLIST Your installer must have completed and checked the following: • The dishwasher is square and level. • The dishwasher is fastened securely to the cabinetry. • The dishwasher door opens and closes freely. The dishwasher door must close without hitting any cabinetry or counter top. • The inlet water supply is turned on and checked for leaks. • The drain hose has been connected and checked for leaks. There must be no kinks or obstructions in the drain hose.
