Fill Angle o Angle Increase o ON OFF The starting angle of infill pattern Fill Angle increase after each layer Angle Increase = 30o Layer 1 Layer 2 Layer 3 Final Pattern Layer 3 Final Pattern Layer 3 Final Pattern Angle Increase = 45o Layer 1 Layer 2 Angle Increase = 90o Layer 1 Support Angle 1 Support Angle 2 Profile/Fill Overlap Bottom Overlap o o N/A N/A Layer 2 Angle of support infill Angle of sparse support infill Overlap ratio between Perimeter and Infill Overlap ratio between Peri
3.Special Special Options Fill Mode N/A mm Tolerance mm Fuse Gap Hole Shrink (only applied to vertical shrink effect) mm Max. Radius Ratio N/A Max Shrink N/A Entity ID Profile Inner Profile Top Bottom Infill Support Support Hatch Raft Fill = Perimeter+infill+top/bottom Shell = Perimeter+top/bottom (no infill) Vase = Perimeter only (no infill, no top/bottom) +0.1 = X and Y plane both increase 0.1mm in size Radius for small gap to be fused.
Raft Raft Base Jump mm/s mm/s mm/s Print speed of raft layers Print speed of first layer of raft Speed of jumps (non- printing movements of extruder) Temperature Temperature Tune ℃ Profile Tune Infill Tune ℃ Support Tune ℃ Raft Tune ℃ Support Peel Set increase/decrease of nozzle temperature when printing Perimeters Set increase/decrease of nozzle temperature when printing Infill Set increase/decrease of nozzle temperature when printing Support Set increase/decrease of nozzle temperature when print
Platform Preheat Preheat platform for max.15 minutes before printing starts. Within 15 minutes, printing will start as soon as target temp reach. De-initialize the printer when current print job finishs. When De-initialized, the printer consume less power and produce lower noise.
Print End Layer Start Layer End Profile Start Profile End Infill Start Infill End Support Start Support End Path Start Path End location for customized functions. Accepted Gcodes: Mat Lib (Material Library) Filament Type Material ID Manufacturer Fila. Dia.
Part Sub-setting Save Mesh Basic Info Add Child Model Delete Model Add Child Profile Model Print Profile Save Mesh Delete Model Add Child Model Model Print Profile Add Child Profile Link to Main Setting Link to Main Setting Save the model to .UP3 format Delete the model from the part list Add a child model, please refer to “Part Optimization” Click to edit the print profile for the model, settings changed only apply to this model and will not be affecting other models on the list.
Setting child profile is same setting of main profile. However some settings are not available in child profiles, eg. Layer thickenss. Child profile allow user to adjust print speed, temperature, extrusion scale, infill density, and etc for a particular vertical section of the part 2. Optimize on X-Y plane Use child model could allow user to optimize the part on another dimension. 1. Click “+” button add child model. a cylinder is added as a child model for the cube. 2.
7. Wand - the Printer Hosting Software UP Studio 3.0 is a package that includes two softwares; UP Studio now become an independent slicer and the printer hosting functions were spin off into a new software called “Wand” UP Studio 3.0 only handle modeling slicing and all printer communication, operation and maintenance functions are moved to Wand. Therefore when after slicing, user need to save the sliced data (.tsk) to hard drive and then use Wand to send the .tsk file to the printer. 7.
3. X-Y axes Control 4. Z-axis Control 5. Extruder Settings 6. Maintenance 7. Printer Info :current axial coordinates. Platform Map, click the squares to move the print head to corresponding X-Y location on the platform. Red square( ) indicate current location Z axis indicator: black dot indicate current Z location of print head.
7.4 Ethernet Connection Find a Ethernet cable. Insert the connector into the LAN socket on the back of your UP300D, and a LAN icon will appear on the touchscreen. To edit the Ethernet Network Settings in UP Studio: Open Up Studio in you computer, and go to Settings, find the printer under Printer section, then click Information button to make further changes.
7.6 Wi-Fi Connection To connect your UP300D, you can set it up through UP Studio on your computer or use the touchscreen on the UP300D. Use the UP Studio on the computer: 1, Connect your UP300D with a USB cable to your computer, 2. Open UP Studio on your computer, go to Settings, choose Printer. 3. The connected UP300D will appeared with a green tick on top, click More (circled in the red). 4, Click the down drop down menu, and then select the desired Wi-Fi network to connect.
If you cannot find your UP300D in the printer list, click Refresh. 7, An icon of your UP300D will appear in the Printer section, Click the icon, a green check mark representing your UP300D is connected via Wi-Fi successfully will appear on top of the UP300D icon. Using the touchscreen on the UP300D to setup the Wifi connection: Go to Config, click Network Settings. Select network name on the list, type in password if required, and press return.
