RFID MODULE Mifare Reader / Writer SL032 User Manual Version 3.
StrongLink SL032 V3.1 CONTENT 1. MAIN FEATURES ................................................................................. 3 2. PINNING INFORMATION .................................................................. 4 3. BAUD RATE SETTING .......................................................................... 5 4. COMMUNICATION PROTOCOL........................................................ 5 4-1. COMMUNICATION SETTING .................................................................... 5 4-2.
StrongLink SL032 V3.1 1. MAIN FEATURES *This picture may not be exactly the same as real object. • Tags supported: Mifare 1k, Mifare 4k, Mifare UltraLight, Mifare UltraLight C, NTAG203, DESFire, DESFire EV1 and Mifare Plus 2K/4K • Built-in antenna • UART interface, baud rate 9,600 ~ 115,200 bps • 2.7 ~ 3.6V VDC operating, I/O pins are 5V tolerant • Work current less than 45mA @3.
StrongLink SL032 V3.1 2. PINNING INFORMATION PIN SYMBOL TYPE 1 2 3 4 VDD IN TXD RXD PWR Input Output Input 5 OUT Output 6 7 8 9 10 GND NC NC NC NC PWR DESCRIPTION Power supply, 2.7 to 3.6VDC Falling edge wake up SL032 from power down mode Serial output port Serial input port Tag auto-detection signal low level indicating tag in high level indicating tag out Ground Attention: Pin IN must be connected HIGH voltage when working, so SL032 can enter power down mode properly.
StrongLink SL032 V3.1 3. BAUD RATE SETTING R6 & R7 are used for setting baud rate as follows sheet Assembled R6 no yes no R7 no no yes yes yes Baud rate bps 9,600 19,200 57,600 115,200 ( default ) 4. COMMUNICATION PROTOCOL 4-1. Communication Setting The communication protocol is byte oriented. Both sending and receiving bytes are in hexadecimal format. The communication parameters are as follows, Baud rate: 9,600 ~ 115,200 bps Data: 8 bits Stop: 1 bit Parity: None Flow control: None 4-2.
StrongLink SL032 V3.1 4-3.
StrongLink 0x12 0x13 0x14 SL032 V3.1 MFP WritePerso fail MFP CommitPerso fail Ulralight c authenticate fail http://www.stronglink-rfid.
StrongLink SL032 V3.1 4-4. Command List 4-4-1.
StrongLink SL032 V3.1 4-4-3. Read a data block 0xBA Len 0x03 Block Checksum Block: The block number to be read, 1 byte Response: 0xBD Len 0x03 Status Data Checksum Status: 0x00: Operation succeed 0x04: Read fail 0x0D: Not authenticate 0xF0: Checksum error Data: Block data returned if operation succeeds, 16 bytes. 4-4-4. Write a data block 0xBA Len 0x04 Block Data Checksum Block: The block number to be written, 1 byte. Data: The data to write, 16 bytes.
StrongLink SL032 V3.1 0x05: Write fail 0x06: Unable to read after write 0x0D: Not authenticate 0xF0: Checksum error Value: Value written if the operation succeeds, 4 bytes. 4-4-7. Write master key (key A) 0xBA Len 0x07 Sector Key Checksum Sector: The sector number to be written, 1 byte.
StrongLink SL032 V3.1 0xF0: Checksum error Value: The value after decrement if the operation succeeds, 4 bytes 4-4-10.
StrongLink 4-4-13. Download Key 0xBA Len 0x12 Sector Type Key Sector: 0 - 39 Type: Key type (0xAA: KeyA, 0xBB: KeyB) Key: 6 bytes, stored in SL032 Response: 0xBD Len 0x12 Status Checksum Status: 0x00: Operation succeed 0x08: Address overflow 0xF0: Checksum error SL032 V3.1 Checksum 4-4-14.
StrongLink SL032 V3.1 4-4-17. LED Control 0xBA Len 0x40 Data Checksum Data: 0x00: LED off 0x01: LED on Return: 0xBD Len 0x40 Status Checksum Status: 0x00: Operation succeed 0xF0: Checksum error http://www.stronglink-rfid.
StrongLink SL032 V3.1 4-4-18. Power Down 0xBA Len 0x50 Checksum Response: 0xBD Len 0x50 Status Checksum Status: 0x00: Operation succeed 0xF0: Checksum error 4-4-19. 3Des Authentication(Utralight C) 0xBA Len 0x60 Key Checksum Key: 16 bytes Response: 0xBD Len 0x60 Status Checksum Status: 0x00: Operation succeed 0x14: Authenticate failed 0xF0: Checksum error 4-4-20.
StrongLink 0xF0: SL032 V3.1 Checksum error 4-4-22. Commit Perso 0xBA Len 0x81 Checksum This command commit the Write Perso and switch the card to security level 1(SL1 card) or level 3(SL3 card).
StrongLink SL032 V3.1 5. DIFFERENCES FROM PREVIOUS VERSION Although we make efforts on the compatibility between the new SL032 V3.1and the old SL032, there are still some differences you need to know. 1. New SL032 has the auto-detection function which can close automatically when there is a DESFire or MifarePlus L0/L2/L3 card coming into the detection range. By the way, we also offer you the Turn On/Off Auto-detection command. 2.
Federal Communications Commission (FCC) Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
OEM Integration Instructions： This device is intended only for OEM integrators under the following conditions: The module can be used to installation in other host. The antenna must be installed such that 20 cm is maintained between the antenna and users, and the transmitter module may not be co-located with any other transmit or antenna. The module shall be only used with the integral antenna(s) that has been originally tested and certified with this module.
