BL-M6158NS1 SPEC
BL-M6158NS1 SPEC Content 1. General Description ...................................................................................................................................3 2. Product Model Information ....................................................................................................................3 3. WIFI Specification .......................................................................................................................................3 3.1 WIFI features ......
BL-M6158NS1 SPEC 1. General Description BL-M6158NS1 wireless SDIO module is designed base on SV6158. It operates at 2.4~2.4835GHz supports IEEE802.11/b/g/n 1T1R, wireless data rate can reach up to 150Mbps. The SDIO interface complies with SDIO 1.1/2.0 and SPI. It supports external antenna, which adapts different kinds of work environment. It’seasy and convenient to connect wireless network. 2. Product Model Information Model Number BL-M6158NS1 FCC ID 2AN2O-RSW03 IC 23317-RSW03 3.
BL-M6158NS1 SPEC 3.2 WIFI RF Performance Feature Description Standard IEEE 802.11 b/g/n 802.11b: 1, 2, 5.5, 11Mbps; 802.11g: 6, 9, 12, 18, 24, 36, 48, 54Mbps; Data Rate 802.11n (HT20): MCS0~MCS7(1T1R_SISO) 6.5~72.2Mbps; 802.11n (HT40): MCS0~MCS7(1T1R_SISO) 13.5~150Mbps; IEEE 802.11b mode: CCK, DQPSK, DBPSK Modulation mode IEEE 802.11g mode: 64QAM, 16QAM, QPSK, BPSK IEEE 802.
BL-M6158NS1 SPEC 3.3 Block Diagram 3.4 Dimension 12.0*12.0*1.8mm (LxWxH) ,Tolerance: +/-0.
BL-M6158NS1 SPEC 3.5 PIN Assignment Pin # Name Type Description 1 GND P Ground 2 RF I/O WLAN RF pad/2.
BL-M6158NS1 SPEC 4 NC / NC 5 GPIO12 I/O Strapping Purpose I/O Pins 6 NC / NC 7 NC / NC 8 NC / NC 9 VDD P VDD3.3V power supply 10 NC / NC 11 NC / NC 12 LDO_EN I Reset signal to power down IC 13 WAKE_UP_HOST I/O General Purpose I/O Pins 14 SD_D2 I/O SDIO data 2 15 SD_D3 I/O SDIO data 3t 16 SD_CMD I/O SDIO command 17 SD_CLK I SDIO clock 18 SD_D0 I/O SDIO data 0 19 SD_D1 I/O SDIO data 1 20 GND P Ground 21 NC / NC 22 VDDIO P VDDIO3.
BL-M6158NS1 SPEC I: input O: output P: power 3.
BL-M6158NS1 SPEC 4. Antenna Specification 4.1 Antenna lists Max No. Type Band(s) 1 PCB antenna 2.4GHz - 2.5GHz 3.7 2 PCB antenna 2.4GHz - 2.5GHz 3.3 roborock S6 3 PCB antenna 2.4GHz - 2.5GHz 4.2 roborock S4 4 PCB antenna 2.4GHz - 2.5GHz 3.7 roborock S5 Max 5 PCB antenna 2.4GHz - 2.5GHz 3.7 S5 Max Peak Gain(dBi) Host Model S501-01, S511-01, S551-01 4.
BL-M6158NS1 SPEC 4.3 Antenna design requirements a) RF-line need 50Ω single line impedance; b) Antenna is 2.4G WiFi Frequency band MIFA type Board antenna c) Antenna length, width, shape(s) as follows,Company:mm; d) PCB thickness is 1.
BL-M6158NS1 SPEC 5. FCC and IC Warning This device complies with Part 15 of the FCC Rules / Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
BL-M6158NS1 SPEC To satisfy FCC / IC RF exposure requirements, a separation distance of 20 cm or more should be maintained between the antenna of this device and persons during device operation. To ensure compliance, operations at closer than this distance is not recommended. Les antennes installées doivent être situées de facon à ce que la population ne puisse y être exposée à une distance de moin de 20 cm.