F89ETSM13-W2 SPEC
F89ETSM13-W2 SPEC Content 1. General Description ...................................................................................................................................3 2. Product Model Information ....................................................................................................................3 3. WIFI Specification .......................................................................................................................................3 3.1 WIFI feature ......
F89ETSM13-W2 SPEC 1. General Description The F89ETSM13-W2 is a highly integrated single-chip 802.11n Wireless LAN (WLAN) network SDIO interface (SDIO 1.1/ 2.0/ 3.0 compliant) controller. It is a WLAN MAC, a 1T1R capable WLAN baseband, and WLAN RF in a single chip. It provides a complete solution for a high throughput performance integrated wireless LAN device. 2. Product Model Information Model Number F89ETSM13-W2 FCC ID 2AN2O-RSW01 IC 23317-RSW01 3. WIFI Specification 3.
F89ETSM13-W2 SPEC 3.2 WIFI RF Performance Feature Description Standard IEEE 802.11 b/g/n 802.11 b: 11, 5.5, 2, 1 Mbps 802.11 /g: 54, 48, 36, 24, 18, 12, 9, 6 Mbps Data Rate 802.11 n: MCS 0 to 7 for HT20MHz:65 Mbps MCS 0 to 7 for HT40MHz:150 Mbps IEEE 802.11b mode: CCK, DQPSK, DBPSK Modulation mode IEEE 802.11g mode: 64QAM, 16QAM, QPSK, BPSK IEEE 802.11n mode : 64QAM, 16QAM, QPSK, BPSK Ad-hoc Mode(Peer-to-Peer) Network Architecture Infrastructure mode Scatter Net Frequency Range 2.4GHz band: 2.
F89ETSM13-W2 SPEC 3.3 Block Diagram 3.3V Antenna SDIO/GSPI PA 2.4GHz HOST Interface CLK 3.4 Dimension Unit ±0.
F89ETSM13-W2 SPEC 3.5 PIN Assignment Pin # Name Description 1 GND GND 2 RF RF OUTPUT 3 GND GND 4~8 NC NC 9 VBAT 3.3 or 4.
F89ETSM13-W2 SPEC 20 GND GND 21 NC NC 22 VDIO 1.8~3.3V 23~30 NC NC 31 GND GND 32 NC NC 33 GND GND 34~35 NC NC 36 GND GND 37~40 NC NC 41 GND GND 42~44 NC NC 3.
F89ETSM13-W2 SPEC 石头世纪科技有限公司 内部文档 8
F89ETSM13-W2 SPEC 4. Antenna Specification 4.1 Antenna List Max No. Type Band(s) 1 PCB antenna 2.4GHz - 2.5GHz 3.7 2 PCB antenna 2.4GHz - 2.5GHz 3.3 roborock S6 3 PCB antenna 2.4GHz - 2.5GHz 4.2 roborock S4 4 PCB antenna 2.4GHz - 2.5GHz 3.7 roborock S5 Max 5 PCB antenna 2.4GHz - 2.5GHz 3.7 S5 Max Peak Gain(dBi) Host Model S501-01, S511-01, S551-01 4.
F89ETSM13-W2 SPEC 4.3 Antenna design requirements: 1) RF-line need 50Ω single line impedance; 2) Antenna is 2.4G WiFi Frequency band MIFA type Board antenna 3) Antenna length, width, shape(s) as follows,Company:mm; 4) PCB thickness is 1.
F89ETSM13-W2 SPEC 5. FCC and IC Warning This device complies with Part 15 of the FCC Rules / Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
F89ETSM13-W2 SPEC To satisfy FCC / IC RF exposure requirements, a separation distance of 20 cm or more should be maintained between the antenna of this device and persons during device operation. To ensure compliance, operations at closer than this distance is not recommended. Les antennes installées doivent être situées de facon à ce que la population ne puisse y être exposée à une distance de moin de 20 cm.