User Manual

ManualsBrandsBeijing Noitom Technology ManualsElectronicsPerception Neuron Studio

Description

E01-NYT-02 is a

100m W i ndustrial-grade w ireless t ransceiver i ntegrated data t ransmission module w ith

high speed (maximum air speed is up to 2Mbps) and high stability working in 2.4GHz frequency. The module

uses NORDIC original nRF24L01P RF chip and RFX2401C power amplifier chip, built-in LNA with receiving

sensitivity increased by 10dBm and works in the 2.402GHz ~ 2.482G

Hz ISM band.It has

small harmonics, small channel crosstalk , ultra-

small

size.

All ar e M urata

original B level material, it is the

industrial

standard

model.

Electrical characteristics

NO. Parameter

name Parameter values Abstract

1 RF chip nRF

24L01P Nordic

2 O

frequency 2.402GHz~2.482GHz

Adjusta

ble，1MHz step by step

3 Supply Voltage 1.8~

3.6VDC Voltage higher than 3.6Vwill

damage the module permanently

Communic

ation level 0.7VCC~5V

VCC means the module’s

supply voltage

5 Air rate 250k~2Mbps

3 levels adjustable(250kbps、

1Mbps、2Mbps)

6 Turn off

current 1.0uA Set nRF4L01P as power

down，CE as low level

7 Sending current 150Ma@dBm Power supply must be more

than 250mA

8 Receiving

current 23mA CE=1

9 Communica

tion

Interface

SPI The maximum rate is up to

10Mbps

10 RSSI s

upport Not support Only supports simple

packet-loss statistics

11 Receiving

sensitivity -94dBm@250kps See the chip manual for details

12 O

tion

temperature

-40~+85℃

Industrial grade

13 Storage

temperature

-40~+125℃

Industrial grade

14 O

tion

humidity 10%~90%RH No condensation

good spectrum characteristics,

Summary of content (6 pages)

PAGE 1
Description E01-NYT-02 is a 100m W i ndustrial-grade w ireless t ransceiver i ntegrated data t ransmission module w ith high speed (maximum air speed is up to 2Mbps) and high stability working in 2.4GHz frequency. The module uses NORDIC original nRF24L01P RF chip and RFX2401C power amplifier chip, built-in LNA with receiving sensitivity increased by 10dBm and works in the 2.402GHz ~ 2.482GHz ISM band.It has good spectrum characteristics, small harmonics, small channel crosstalk , ultra- small size.
PAGE 2
Pin Description
PAGE 3
Regulatory Module Integration Instructions 2.2 List of applicable FCC rules This device complies with part 15.249 of the FCC Rules. According to the definition of mobile and fixed device is described in Part 2.1091(b), this device is a mobile device. 2.3 Summarize the specific operational use conditions This module can be used in household electrical appliances as well as lighting equipments. The input voltage to the module should be nominally 3.3V VDC ,typical value 3.
PAGE 4
2.8 Label and compliance information The outside of final products that contains this module device must display a label referring to the enclosed module. This exterior label can use wording such as: “Contains Transmitter Module FCC ID: 2ABTR- E01-NYT-02 ”,or “Contains FCC ID: 2ABTR- E01-NYT-02 ”, Any similar wording that expresses the same meaning may be used. 2.
PAGE 5
all the applicable individual technical rules as well as to the general conditions of operation in Sections 15.5, 15.15, and 15.29 to not cause interference. The operator of the host product will be obligated to stop operating the device until the interference has been corrected 2.
PAGE 6
Operating the host product When testing the host product, all the transmitters must be operating.The transmitters can be enabled by using publicly-available drivers and turned on, so the transmitters are active. In certain conditions it might be appropriate to use a technology-specific call box (test set) where accessory devices or drivers are not available. When testing for emissions from the unintentional radiator, the transmitter shall be placed in the receive mode or idle mode, if possible.