Model MC6 1
◆ Table of Contents Product Image.............................................................1 Table of Contents.......................................................2-5 Introduction................................................................6-9 Mode Selection.............................................................10 Mode 1-Thermostat.......... .........................................12 LCD Display............................................................
Hold Mode..............................................................17-18 Holiday Mode..........................................................19-20 Away Mode..............................................................21 Schedule..................................................................22-25 Optional Functions................................................26-29 Optional Features Table.........................................30-32 Feature Settings Clock Setting.................................
Standby Screen........................................................................35 Screen Lock..........................................................................36-37 Temperature Format..................................................................39 Temperature Limit......................................................................40 Defrost.......................................................................................41 Sensor Selection..........................................
Reset To Factory Settings.........................................................47 Installation...........................................................................48-51 Mode 2-Time Clock...................................................52 LCD Display........................................................................53-56 Boost........................................................................................56-57 Setting the Switching Times...............................................
◆Introduction What is a Programmable Thermostat? A programmable room thermostat is a device that combines the functions of both a room thermostat and timed heating controller into a single unit. The programmable thermostat is used to switch the heating system in your home on and off as needed. It works by controlling the temperature according to a series of programmed temperature settings that take effect at different times of your choosing.
different times of the day (and days of the week) to meet your particular needs. Adjusting a room thermostat to a higher setting will not make the room heat up more quickly. How quickly the room heats up depends on the design of the heating system and heat-loss of the building. For example, the size of boiler and radiators. Neither does the setting affect how quickly the room cools down.
temperature first, for example 18°C, and then adjust the temperature gradually up or down by one degree each day until you are comfortable with the temperature. The higher a temperature setting required will result in more energy and fuel cost. If your heating system uses radiators, there will usually be only one programmable room thermostat on each floor to control the house.
All types of thermostats need a free flow of air to sense the best temperature, so they must not be placed in a cupboard or covered by curtains or blocked by furniture. Radiant heat by the sun, shining directly onto the thermostat through a window and heat from nearby electric fires, televisions, wall or table lamps may prevent the thermostat from reading the correct average temperature in the room properly.
Mode Select MC6 can either be used as a Thermostat or a Time-clock. Thermostat Mode (Fully Programmable Mode) – Allows Time & Temperature Settings to be made. This allows the thermostat to be programmed for a specific temperature during a specific time. Time-clock Mode – Allows for Time ONLY setting to switch ON or OFF as desired. This Mode ignores any temperature requirement.
Follow these steps (Use your finger as the screen is Touch Sensitive) ★Press the icon ★Use the icon and enter Feature Settings. / to turn page to 4. Find ‘Work Mode’ Selection, click it and enter Selection Interface. ★Select ‘Heating Mode’ or ‘Timer Mode’ the thermostat will re-set and enter the desired Mode.
Mode 1-Thermostat 12
◆LCD Display 1. Wi-Fi indicator- Displayed when connected to a Wi-Fi Network 2. Hold: Temperature Hold. 3. Adjusting the optional settings. 4. Day Indicator & Clock 5. Away: Means the MC6-Timer is maintaining a lower temperature to give frost protection.
6. OPT (Optimum): Displayed ON/OFF of the ‘Optimum Start’ 7. Air Humidity: 8. Power ON/OFF 9. Holiday: Displayed when thermostat is in holiday mode. 10. Schedule: Programmable Operation. 11. Setup Button 12 & 13 Adjusting the Setting Temperature or turning a page. 14. Set-point Temperature display 15.
. Temperature reading is in Degrees ℃ or ℉ Display 17. Display shows “Heating” flame symbol (A flame on screen means heating is ON.
◆Operation of Main Display Hold The Temperature hold function allows you to manually override the current operating program and set a different temperature for a desired period. ★Press the ‘Hold’ and enter the setting interface.
set the desired Hold Temperature. (Temperature Range 5℃ -35℃). ★Press the Second/Third columns of Hour/Minute, use the icon / to set the desired “Hold Time” ★Press the icon to save and return to main display, or click ‘Cancel’ to delete the setting. You will see the ‘HOLD’ time remaining: **:** indication is displayed on screen. The time will count down for the set duration and then revert to the normal program setting.
Holiday The MC6 will maintain this temperature for the duration of the holiday and will then automatically return to the program mode on your return. ★Press the “Holiday” and enter setting interface.
★Press the column of Years/Month/Day, Use the icon / to set the Year/Month/Day values under Holiday End. ★Press the icon to save and return to main display. The display shows; ‘Holiday until’ **/** **:** OR press; ‘Cancel’ to delete the setting.
Away Mode ◆In ‘Away Mode’, The MC6 will only turn the Heating ON should the room temperature drop below the set Defrost Temperature (This is configured in the setup). If the heating is turned on in Away Mode, the Flame symbol will be displayed.
Schedule ★Press the icon and enter Feature Settings. ★Find the ”Schedule “ option. Press it and enter setting interface. There are four Options: Weekday/Weekend, 7Days, 24Hours, None ※Press the icon will turn to in the front of Weekday/Weekend, and it .
※Press the icon to save and return to main screen. ※Press the “Schedule” on the main screen. ※Press “Schedule” and enter “Edit” interface. ※On the Edit Page,“Weekday/Weekend”can be selected to edit. ※Press “Weekday” and enter editing interface.
(Each Time Period has Options) ※Morning: Press the First Column of “Time”, use the icon to set desired “Hour” Press the Second Column of “Time”, use the icon to set desired Minute.
Click the Third Column of “Temperature”, use the icon to set desired Temperature. For Example: The Setting Temperature is 20℃ Repeat these steps to set all periods.
◆Optional Functions Program Mode: Program Mode: MC6 thermostat provides three programming modes and also can be set to non-programmable thermostat Weekday / Weekend (5 + 2) Programming - Allows you to edit the 4 time periods for the weekday and 4 time periods for the weekend. 7 day programming mode - can be programmed every day for 4 time periods with comfortable temperature 24 hours mode -Every day can be edited 4 time periods with comfortable temperature.
thermostat is in Away Mode. The range is 7-17℃.The default is 7℃ and is suitable for most applications. Temperature Format: Selecting between ℃ and ℉. Switch Diff: This function allows you to increase the switching differential of the thermostat. The system defaults to 0.5 degrees, meaning that when the temperature is set to 20 degrees, the thermostat will start heating at 19.5 degrees and stop at 20 degrees. If the default value is 1 degree, start heating at 19 degrees, stop at 20 degrees.
Sensor Selection: You can select which sensor should be used. You can select between air temperature only, floor temperature, or both. When you enable both sensors, the floor sensor is used as a floor limiting sensor and is designed to prevent the floor from overheating. Floor Temp Limit: The function is available when the floor sensor is enabled. You can set a floor temperature limit between 20-45 degrees (default is 27 degrees).
Optimum Start Optimum Start will calculate how much time the heated space needs, to ensure the required Temperature you have set, at the Time you have set, is achieved (assuming the heating system has been installed to meet the energy requirements of the building). For example if you require 21degC at 8am, the thermostat will calculate how much time in advance, the system needs to operate to achieve this setting. This time is calculated by the thermostat in Minutes per 1DegC Room temperature rise.
◆Optional Features Table FEATURE SETTING Program Mode Weekday/Weekend(Default)/7 Days Programming/24 Hrs/None Defrost (Away Mode) 7℃-17℃(7℃ =Default) 30
Temperature Format Switch Diff ℃/℉(℃=Default) 0.5℃-3℃ (0.
Remote Air &Floor Sensor Floor Temp Limit 20℃-47℃ (28℃=Default) Optimum Start/Rate Minutes to raise temperature by 1 ℃ of Change Ambient Light ON/OFF Dimming 32
◆Feature Settings Clock Setting To set the clock, follow these steps. ★Press the icon ★Press and enter Feature Settings. The “Clock Setting” enter Setting Interface ★Press the column of Year/Month/Day, use the icon / to set the Year/Month/Day values. ★Press the column of “Time”, use the icon / to set Hours/ Minute.
★Press the icon to save and return to main screen. Backlight Setting ★Press the icon ★Press and enter Feature Settings. “Backlight” Selection and enter Backlight Setting. ★Ambient Light Dimming is in Mode: Automatically adjusts the backlight brightness. ★Ambient Light Dimming is in Mode: Manually adjust the backlight brightness.
★Use the icon ★Press the icon / to adjust to the desired brightness to save and return to main screen. Standby Screen ★Press the icon ★Press and enter Feature Settings. “Standby Screen” and enter Setting interface. ★There are Four Selections (3Min,10Min,Just Night, Never) to control the Standby Screen Time.
★For example, setting the standby time is for 10 minutes in the front of “10 Min” and it will turn to Press the icon . ★Press the icon to save and return to main screen. Screen Lock ★Touch (Press ★Press on) the icon and enter Feature Settings. “Screen Lock” and enter setting interface.
Lock Pin Options ★For example, Setting the Lock Pin is 5209 ※Press the First Column, use the icon / ※Press the Second Column, use the icon ※Press the Third Column, use the icon ※Press the Fourth Column, use the ★Press the icon / / / to set to 5 to set to 2 to set to 0 to set to 9 to save and return to main screen.
Note: To unlock the MC6 press .The display will show and you will need to enter the four digit pin number you set previously.
Temperature Format ★Press the icon and enter Feature Settings. ★Find the “Temp Format” option, Press interface. ★There are two Options ★Press the icon turn to it and enter setting / in the front of or ,and it will .
★Press the icon to save and return to main screen. Temperature Limit ★Press the icon and enter Feature Settings. ★Find the “Temp Limit ” option, Press it and enter setting interface.
Maximum Temperature to 6-35℃ ★Press the icon twice to save and return to main screen. Defrost The thermostat will automatically enter the Defrost Mode when the room temperature drops below the defrost temperature. ★Press the icon and enter Feature Settings.
interface. Temperature ★Use the icon ★Press the icon Options. / to adjust the temperature. twice to save and return to main screen.. Sensor Selection ★Press the icon and enter Feature Settings.
★Find the “Sensor Selection” option, Press it and entry in setting interface. ★Press the icon ★Press the icon of which sensor you required.
. Floor Temperature Limit ★Press the icon and enter Feature Settings. ★Find the “Floor Temp Limit” option, Press it and entry in setting interface. ★Use the icon ★Press the icon / to set the temperature. twice to save and return to main display.
Daylight Saving Time ★Press the icon ★Press and enter Feature Settings. “DST” and enter setting interface.
★Press the icon turn to in the front of “EU/U&C/A&Z” and it will . ★Press the icon twice to save and return to main screen. System Information ★Press the icon and enter Feature Settings.
Version Number: 2.0 ★Press the icon to Exit Reset to Factory Settings Warning: Reset will make you lose the current Settings and return to the factory Settings. ★Press the icon and enter Feature Settings.
★Press “ ”and enter setting interface. ★Press “Reset” to factory settings ★Press the icon to Exit Installation Install the thermostat at a height in accordance with the local Building Regulations. All electrical work must be carried out by a suitably qualified electrician.
Please read the instructions in order to better understand our products. Do not install in areas close to a heat source, which will affect its function. This MC6 thermostat is designed to be flush mounted and requires a 35mm electrical recessed flush mounted box within the wall. Step 1 Using a flat-blade screwdriver, loosen the screw from the bottom of the thermostat, and then separate the front half from the back-plate.
First place the front panel of the thermostat in a safe place. And then follow the wiring diagram on page 52 & 63 of this manual for the required connecting terminals. Step 3 Screw the thermostat back-plate onto the electrical recessed box in the wall Step 4 Once the back-plate is secure, re-fit the thermostat front panel to the back-plate and gently tighten the bottom retaining screw.
Max Switch Current: 16A LCD screen size: 3.5 Inch Touch: Capacitive touch Dimension: 96 * 86 * 42.
Mode 2-Time Clock 52
◆LCD Display 53
1. WiFi Indicator-Displayed when connected to a WiFi network 2. Away-Displayed when Away Mode is active. 3. Boost-Adjusting the optional setting. 4. Day Indicator & Clock 5. OPT (Optimum): Displayed ON/OFF of the “Optimum Start” 6. Air Humidity: 1) If humidity value less than 30%, the pointer will be in the Red area.
in the Green area. 3) If humidity value is more than 60%, the pointer will be in the Grey area. 7. Power ON/OFF 8. Holiday: Displayed when Time Clock is in holiday mode. 9. Schedule: Programmable Operation. 10. Setup Button 11. Room Temperature display 12.
13. Timer Status-Displays the current status of the timed output. Boost To boost the timed output ON follow these steps. ★Press the “Boost” on main screen & enter setting interface.
desired ★Press “Minute” and use the icon / to set the minutes desired. ★Press the icon to save and return to main screen. ★Boost he remaining time will now be displayed.
Setting the Switching Times To program the switching times, follow these steps ★Press the “Schedule” on main screen. ★Press “Weekday” and enter setting interface. Four Time Periods can be selected to program.(Each Period has ★Press “Hour” of Options) time and use the icon / to set the desired hour.
★Press “Minute” time and use the icon / to set the desired minutes. ★Press “Hour” of time and use the icon / time and use the icon / to set the desired hour. ★Press “Minute” to set the desired minute. Repeat these steps to set all periods.
◆Optional Features Table FEATURE SETTING Program Mode Weekday/Weekend(Default)/7 Days Programming/24 Hrs/None 60
Out Delay 0-15Minutes(0=Default) Ambient Light ON/OFF Dimming 61
FCC Caution: Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.